Barco Xlm Hd30 Owners Manual

1. Packaging and Dimensions
Front view
210
669
810
598
15
327
636
Image 1-3
Front view
To p v i e w
27,546827,5
1130
Image 1-4
To p v i e w
1.6 Free download of Projector Toolset
About Projector Toolset
Projector Toolset is a software tool to set up, configure, manage and control Barco projectors.
R59770014 XLM HD30 25/05/2009
7 

1. Packaging and Dimensions
The concept of this Projector Toolset software is modular. The basic package can be extended with several optional device plug-in
modules, now and in the future available.
The Projector Toolset software works with configurations that can be loaded. Within a configuration, different snapshots can be take.
A snapshot represents a current state of a configuration and can be reloaded to return to this typical state. These terms will be used
through the complete software.
Projector...

2. Installation Guidelines
2. INSTALLATION GUIDELINES
Overview
• General guidelines
• Restricted Access Location
• Projector configuration
• Safety Area around projector
• Lenses
• Mounting the lamp house
• Transporting the projector
• Battery Insertion in the Remote Control
• Battery insertion in the Rugged remote control
• Charging the batteries of the rugged remote control
• Stacking Two Projectors
• Rigging points and clamps
2.1 General guidelines
WARNING:Before installing the projector, readfirst the...

2. Installation Guidelines
Special Care for Laser Beams
Special care should be used when DLP projectors are used in the same room as performant laser equipment. Direct or indirect hitting
of a laser beam on to the lens can severely damage the Digital MicroMirror Devices™ in which case there is a loss of warranty
Which screen type ?
There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear
projection applications.
Screens are rated by...

2. Installation Guidelines
2.3 Projector configuration
Which configuration can be used ?
The projector can be installed to project images in four different configurations:
• Front/table
• Rear/table
• Front/ceiling
• Rear/ceiling
Positioning the projector
The projector should be installed perpendicular with the screen on a distance PD and water leveled in both directions. The mounting
positions in the following images are shown for a nominal lens position.
PD
B
SH
(4)
SH
SW
(5)
A
CD = SH/2 + B - ACD
(5)
SW...

2. Installation Guidelines
PDB
SH
SH
SW
(3)
SW
(4)
A(4)
(3) (2) (1)
CD
Image 2-3
Front-ceiling configuration
(1) Side view
(2) Top view
(3) Back view
(4) Ceiling
CD distance between projector and ceiling
PD Projector distance, distance between screen and projector
SW Screen width (image width)
SH Screen height (image height)
12
R59770014 XLM HD30 25/05/2009 

2. Installation Guidelines
2.4 Safety Area around projector
Safety area
A
A
A B
B
Image 2-4
Air inlet - outlet
A Air inlet
B Air outlet
Due to the airflow, the following free area is recommended :
• Lens side :
- within Light beam : within 2 meter no combustible materials.
- air inlet : 0.5 meter free area
• Backside : within 1 meter no combustible materials.
• Left and right side : 0.5 meter
2.5 Lenses
Overview
• Lenses
• Lens formulas
• Lens installation
2.5.1 Lenses
Available lenses
Lenses
Order...

2. Installation Guidelines
2.5.2 Lens formulas
Formulas
Lenses
Formulas
XLD (1.45-1.8:1) PDmin=1.45 x SW
PD
max=1.80 x SW
XLD (1.8-2.4:1) PDmin=1.80 x SW
PD
max=2.40 x SW
XLD (2.2-3.0:1) PDmin=2.22 x SW
PD
max=2.98 x SW
XLD (2.8-5.5:1) PDmin=2.84 x SW
PD
max=5.50 x SW
XLD (5.5-8.5:1) PDmin=5.50 x SW
PD
max=8.50 x SW
Due to production tolerances the real distances can differ by 2% from these calculated values.
For critical situations (fixed installs that use the lens at one of its extreme zoom positions)...

2. Installation Guidelines
Image 2-6
Mounting lens
For cleaning the lens, see Cleaning the lens, page 128.
2.6 Mounting the lamp house
CAUTION:Never transport the projector with the lamp casing installed. The lamp casing should always been
transported in a vertical way to avoid damaging the lamp.
WARNING:Never attempt to disassemble the lamp from its housing or to dispose of it other than by returning
it to Barco. Due to its high internal pressure, the lamp may explode in either hot or cold state....

2. Installation Guidelines
7. Secure the correct position by turning in both spring lock screws.
8. While the side cover is open, check the manometer. The manometer is situate on the top right of the lamp house compartment.
(image 2-9)
The pressure should be ± 1 bar. When lower than 0.5 bar, a corrective action should be taken by qualified service personnel.
9. Hook on the side cover and close the 3 quarter turn fastener studs a quarter turn clockwise.
Image 2-7
Removing side cover
Image 2-8
Lamp...