Barco Slm R12+ Owners Manual

							5. Getting Started
5. GETTING STARTED
5.1 RCU & Local keypad
How controlling the projector ?
The projector can be controlled by the local keypad or by the remote control unit.
Location of the local keypad ?
The local keypad is located on the input side of the projector.
Remote control functions.
This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely. This
remote control is used for source selection, control, adaptation andset up. It includes automatic storing of picture controls (Bright-
ness, Sharpness...) and settings.
Other functions of the remote control are :
• switching between stand by and operational mode.
• switching to pause (blanked picture, full power for immediate restarting)
• direct access to all connected sources.
5.2 Terminology overview
Overview
The following table gives an overview of the different functionalities of the keys.
COLOR PHASE SHARPNTINT
BRIGHTN
STANDBY
ENTER
TEXTEXIT
PAUSE
2
14 3 5680
9
7CONTRAST
7 9 8 105 12 13 144
-+
-
+
-
+
-
+ -
+
0
9
78
6
5
4
3
2 1
ENTER
14
13
12
9
8
1
2
3
4
5
7
15
32a
PAUSE
-
+PHASE
FREEZ
10
11TEXTEXIT
ADJ
STBY
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
HELP?6
Image 5-1
Local keypad & RCU
R5976654 SLM R12+ 27/01/200547 
						

							5. Getting Started
1Barco keyselection key, to get direct access to the lens adjustment menus.
2ADJADJUST key, to enter or exit the adjustment mode.
3Address key(recessed key), to enter the address of the projector (between 0 and 9). Press the
recessed address key with a pencil, followed by pressing one digit button between
0and9.
4STDYstand-by button, to start projector when the power switch is switched on and to switch
off the projector without switching off the power switch.
5PA U S Eto stop projection for a short time, press ’PAUSE’. The image disappears but full power
is retained for immediate restarting.
6Helpn line help information (not yet available)
7Digit buttonsdirect input selection
8Picture controlsuse these buttons to obtain the desired picture analog level.
9PHASEused to remove the instability of the image.
10TEXTwhen adjusting one of the image, e.g. controls during a meeting, the displayed bar
scale can be removed by pressing ’TEXT’ key first. To re-display the bar scale on the
screen, press ’TEXT’ key again. When TEXT is ’off’, no adjustment menu’s will be
displayed on the screen when entering the adjustment mode.
11FREEZpress to freeze the projected image.
12ENTERto start up the adjustment mode or to confirm an adjustment or selection in the
adjustment mode.
13EXITto leave the adjustment mode or to scroll upwards when in the adjustment mode.
14Cursor keys(on RCU) or ’+’ and ’-’ keys (cursor keys) on the local keypad : to make menu selections
when in the adjustment mode or to zoom/focus when the direct access is active.
Comparison between the cursor keys and the use of the ’+’ and ’-’ keys on the local
keypad : RCU = local keypad
cursor key up = ’+’ key up
cursor key down = ’-’ key down
cursor key right = ’+’ key right
cursor key left = ’-’ key left
Use the ’+’ and ’-’ keys (cursor keys) : toincrease or decrease the analog level of the
image controls when they are first selected.
15RC Operating indicationlights up when a button on the remote control is pressed. (This is a visual indicator to
check the operation of the remote control)
Table 5-1
5.3 Operating the projector
5.3.1 Switching on
How to switch on.
1. Press the power switch to switch on the projector.
- When ’0’ is visible, the projector is switched off.
- When ’1’ is visible, the projector is switched on.
The projector starts i standby mode.
Starting image projection.
1. PressStand bykey once on the local keypad or on the remote control.
48
R5976654 SLM R12+ 27/01/2005 
						

							5. Getting Started
The projector mode indication lamp will be green
-+
-
+
-+
-
+ -
+
09786
5
4
3
2 1
ENTER
32a
PAUSE-
+PHASE
FREEZTEXTEXIT
ADJ
STBY
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRASTHELP?
COLOR PHASE SHARPNTINT
BRIGHTN
STANDBY
ENTER
TEXTEXIT
PAUSE
2
14 3 5680
9
7CONTRAST
A
Image 5-2Or,
Press a digit button to select an input source.
Lamp Run time indication
see chapter 4. Connections, Switching on, page 33
Lamp Light output indication
see chapter 4. Connections, Switching on, page 33
Lamp Z-axis indication
see chapter 4. Connections, Switching on, page 33
5.3.2 Switching to standby
Howtoswitchtostandby?
1. PressStandbyto switch the projector to standby.
Switching to Standby. When the projector is running and you want to go to standby, press the standby key for
2 seconds until the message ’Saving data, please wait’ is displayed. Do not press any longer on the standby
key otherwise the projector will restart.
5.3.3 Switching off
How to switch off the projector?
1. Press firstStandby.
2. Let cool down the projector until the fans stop blowing, at least 15 min.
3. Switch off the projector with the power switch.
5.3.4 Temperature error DMD
Overview
When the temperature of one of the DMD is too low or too high theprojector will be switched automatically to standby. Before
switching to standby, the following message appears for 3 seconds on the screen : ’DMD out of operating temperature range.
Automatic shutdown is activated.’.
A ’-t’ appears on the LED display to indicate the user that the projector is switched to standby due to DMD temperature problems.
Operating temperature range of the DMD : +10°C and +35°C.
R5976654 SLM R12+ 27/01/2005
49 
						

							5. Getting Started
ERROR
DMD out of operating
temperature
range
Automatic shutdown is
activated
Menu 5-1
5.4 Quick Set Up Adjustments
Overview
• Quick Language Change
• Quick Lens Adjustment
• Quick On Screen Color change
5.4.1 Quick Language Change
What can be done?
Only if different on screen languages are available, these can be changed in quick way by following the next procedure.
How to change
1. PressENTERto start up the adjustment mode.
2. Press the cursor key↑or↓to highlightService.
ADJUSTMENT MODE
Select a path from below :
RANDOM ACCESS
INSTALLATION
SERVICE
Select with↑or↓
then 
 to return
Menu 5-2
When password protected, your password will be asked. (more explanation about access by password can be found in Chapter
’Start up the Adjustment mode’.
3. PressENTERto display the Service mode menu.
4. Push the cursor key↑or↓to highlightChange Language. If not visible in the menu, highlight firstMoreand pressENTERto
display a second service menu. Select thenChange Language.
SERVICE
IDENTIFICATION
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJ. ADDRESS
SERIAL COMMUNICATION
NETWORK
LAMP
DIMMING
MORE...
Select with↑or↓
then 
 to return
Menu 5-3
5. PressENTERto display thelanguage selectionmenu.
50
R5976654 SLM R12+ 27/01/2005 
						

							5. Getting Started
6. Push the cursor key↑or↓to highlight the desired language.
CHANGE LANGUAGE
ENGLISH
Select with↑or↓
then 
 to return
Menu 5-4
Note:For the moment, only English is available.
5.4.2 Quick Lens Adjustment
Quick zoom/focus adjustment
1. Press the Selection key*, Barco key.
The zoom/focus menu will be displayed.
LENS ADJUSTMENT ZOOM/FOCUS
ZOOM with     or     ,
FOCUS with       or 
 to shift
 to return
Image 5-3
2. Push the cursor key↑or↓to zoom and←or→to focus the image.
3. When finished, pressEXITkey to return orENTERto continue to the shift adjustment.
Press the selection key * to switch to another pattern. Different patterns are available.
Quick shift adjustment
1. Press the Selection key*, Barco key.
The zoom/focus menu will be displayed (image 5-3).
2. PressENTER.
The shift menu will be displayed.
LENS ADJUSTMENT SHIFT
SHIFT with     or     ,       or 
 to zoom/focus
 to return
Image 5-4
3. Push the cursor key↑or↓to shift the image up or down and←or→to shift the image left or right.
4. When finished, pressEXITkey to return orENTERto continue to zoom/focus.
R5976654 SLM R12+ 27/01/2005
51 
						

							5. Getting Started
Press the selection key * to switch to another pattern. Different patterns are available.
5.4.3 Quick On Screen Color change
What can be done ?
For quick change of the on-screen color of the highlighted items.
The highlighted items on the menus can be displayed in red, green or yellow.
How to change ?
1. PressENTERto start up the adjustment mode.
2. Push the cursor key↑or↓to highlightInstallation.
ADJUSTMENT MODE
Select a path from below :
RANDOM ACCESS
INSTALLATION
SERVICE
Select with↑or↓
then 
 to return
Menu 5-5
3. PressENTERto select.
4. Push the cursor key↑or↓to highlightOSD.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
SOURCE SWITCHING
NO SIGNAL
CONTRAST ENHANCEMENT
CONVERGENCE
CONFIGURATION
LENS
QUICK ACCESS KEYS
OSD
INTERNAL PATTERNS
Select with↑or↓
then 
 to return
Menu 5-6
5. PressENTERto select.
The OSD menu will be displayed.
OSD
HIGHLIGHT ITEM COLOR [red]
MENU POSITION [Default]
Select with↑or↓
then 
 to return
Menu 5-7
6. Push the cursor key↑or↓to highlightHighlighteditemcolor.
7. PressENTERto toggle between red, green and yellow.
52
R5976654 SLM R12+ 27/01/2005 
						

							5. Getting Started
5.5 Using the RCU
Pointing to the reflective screen
1. Point the front of the RCU to the reflective screen surface.
Ceiling
ScreenIR sensor
RCU
Image 5-5
Hardwired Remote Input
1. Plug one end of the remote cable in the connector on the bottom of the RCU.
2. Plug the other end in the connector in the front panel of the projector labelledRC.
OUT IN OnR9840450
HD SDI DIGITAL MODULE
OUT IN On9840110
SDI DIGITAL INPUT
COMM PORT10/(100) BASE-T
RS232/422 OUT
RS232/422 INIR-Receiver Diagnostic Code
Green Operation
Red Stand-by
IR Sync OK
Hardwired
remote
CTRL 1 Hardwired
remote
CTRL 2 Two way
hardwired
remote
CTRL 3
OnOn
OnOn
RCU
DVI INPUT
DVI INPUT
DVI OUTPUT High Bandwidth  5 CABLE INPUT
High Bandwidth  5 CABLE INPUTRGBH/C V
RGBH/C V
Image 5-6
R5976654 SLM R12+ 27/01/200553 
						

							5. Getting Started
Hardwired to the XLR input
1. Plug one end of the remote cable in the connector on the bottom of the RCU
2. Plug the other end in the connector in the front panel of the projector labelledHardwired CTRL2.
OUT IN OnR9840450
HD SDI DIGITAL MODULE
OUT IN On9840110
SDI DIGITAL INPUT
COMM PORT10/(100)BASE-T
RS232/422 OUT
RS232/422 INIR-Receiver Diagnostic Code
Green Operation
Red Stand-by
IR Sync OK
Hardwired
remote
CTRL 1 Hardwired
remote
CTRL 2 Two way
hardwired
remote
CTRL 3
OnOn
OnOn
RCU
Pins XLR plug
1 Ground
2 Signal
3 Ground
DVI INPUT
DVI INPUT
DVI OUTPUT High Bandwidth  5 CABLE INPUT
High Bandwidth  5 CABLE INPUTRGBH/C V
RGBH/C V
Image 5-7
Directly to one of the IR sensors
When using the wireless remote control, make sure you are within the effective operating distance (30m, 100ft in a straight line). The
remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the remote
control unit and the projector IR sensor.
54
R5976654 SLM R12+ 27/01/2005 
						

							5. Getting Started
A DDRADJ EXITSTBY MUTE TEXT
B RIGHTNES S-
+
-+
-+
-
+S HA RPNES S -+TINT
COL ORCONTRAST 
FREEZ09786 5
4
3
2 1
ENTER
RCU
Front of projector
IR sensor
A DDRADJ EXITSTBY MUTE TEXT
B RIGHTNES S-
+
-+
-+
-
+S HA RPNES S -+TINT
COL ORCONTRAST 
FREEZ09786 54 32 1
ENTER
RCU
Rear of projector
IR sensor
Table
45ø 45ø45ø 45ø
Side of projector
ADDRADJ EXITSTBYMU TE TEXT
BRIGHTNESS-
+
-+
-+
-
+S HA RPNES S -+TINT
COL ORCONTRAST 
FREEZ09786 54 32 1
ENTER
RCU
45ø 45ø
Image 5-8
5.6 Projector Address
5.6.1 Controlling the projector
Projector address
Address installed in the projector to be individually controlled.
Common address
Default address. Projector will always execute the command coming from a RCU programmed with that common
address.
Why a projector address ?
As more than one projector can be installed in a room, the separate projector should be separately addressable with an RCU or
computer. There for each projector has its own address.
Set up an individual Projector Address.
The set up of a projector address can be done via the software. See ’Change projector address’ in chapter ’Service mode’.
Projector controlling.
Every projector requires an individual address between 0 and 255 which can be set in the Service mode.
Whentheaddressisset,theprojectorcanbecontrollednow:
• RCU for addresses between 0 and 9.
• computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between 0 and 255.
Common Address
Every projector has a common address ’0’ or ’1’. The choice between ’0’ and ’1’ can be selected in the Service mode.
R5976654 SLM R12+ 27/01/2005
55 
						

							5. Getting Started
5.6.2 Displaying and Programming addresses
Displaying the Projector Address on the Screen.
1. PressAddresskey (recessed key on the RCU) with a pencil.
The projector’s address will be displayed in a ’Text box’
To continue using the RCU with that specific address, it is necessary to enter the same address with the
digit buttons (address between 0 and 9) within 5 seconds after pushing the address key. For example : if the
Address key displays projector address 003, then press 3 digit button on the RCU to set the RCU’s address
to match the projector’s address. Do not press 003 digits. This will address the remote control to ’0’ and
control all projectors in the room. If the address is not entered within 5 seconds, the RCU returns to its default
address (zero address) and control all projectors in the room.
How to Program an Address into the RCU?
1. Press theAddresskey (recessed key on the RCU) with a pencil.
2. Enter the address with the digit buttons within 5 seconds after pushing the address key.
Note:That address can be any digit between 0 and 9.
5.7 Controlling the Projector
Input Selection
Key in the corresponding slot number with the digit keys on the RCU. The selected source will be displayed.
Picture Controls
When an image control is pressed, a text box with a bar scale, icon and function name of the control, e.g. ’brightness...’ appears on
the screen (only if text is ON). See example screen. The length of the bar scale and the value of the numeric indication indicate the
current memorized setting for this source. The bar scale changes as the control stick on the RCU is pressed or the + or - buttons
on the local keypad.
BrightnessA correct ’brightness’ setting isimportant for good image reproduction.
Use the + button for a higher brightness.
Use the - button for a lower brightness.
ContrastA correct ’contrast’ setting is important for good image reproduction. Adjust the contrast to the level
you prefer, according to room lighting conditions.
Use the + button for a higher contrast.
Use the - button for lower contrast.
ColorColor saturation is only active for Video and S-Video. Adjust the color intensity of the picture.
Use the + button for richer colors.
Use the - button for lighter colors.
TintTint is only active for Video and S-Video when using the NTSC 4.43 or NTSC 3.58 system.
Use the + button
Use the - button.
Sharpnessno sharpness available
PhaseUse the arrow buttons to adjust the phase.
The Pause Key
When the Pause key is pressed, the image projection is stopped, a black screen will be displayed and the projector remains with full
power for immediate restart. The sound is not interrupted. The display on front of the projector will show a P.
To restart the image :
•PressPausekey.
•PressEXITkey
• Select a source number.
56
R5976654 SLM R12+ 27/01/2005