Barco Slm R12+ Owners Manual

							3. Installation Guidelines
3.9 Stacking Projectors
What is possible?
Up to 3 projectors can be stacked on each other without using extra tools or accessories.
How to stack?
Handle as follow:
1. Put the second projector on the first one so that base plate of the second projector matches with the rigging socket of the first
projector.
Image 3-23
Stacking two projectors
2. Turn the rigging sockets of the second projector counter clockwise until they are free to move up and down.
Image 3-24
Closing the rigging sockets
3. Secure the projectors on each other by bringing the free part of the second projector into the socket of the first projector and turn
a quarter clockwise while pushing downwards until it clicks in.
4. For ceiling mounted configurations, pull on the hook (A) with the cable of the lowest projector.
R5976654 SLM R12+ 27/01/2005
27 
						

							3. Installation Guidelines
A
Image 3-25
Mounting the security chain
5. Guide hook and cable around the carry handle and guide it around the carry handle of the upper projector.
Image 3-26
Mounting the security hook
6. Hook it in the foreseen hole B in the base plate of the upper projector.
28
R5976654 SLM R12+ 27/01/2005 
						

							3. Installation Guidelines
CB
B
Image 3-27
Mounting the security hook (detail)
How to open a secured rigging point?
1. Push the ring (A) of the first projector downwards and hold it in that position.
A
B
Image 3-28
Opening the rigging sockets
2. Turn the locked part (B) of the second projector a quarter counter clockwise and move it upwards.
R5976654 SLM R12+ 27/01/2005
29 
						

							3. Installation Guidelines
3.10 Rigging points and Accessories
Clamps
Slots are made in the carry handle frame for easy inserting the overlockers and for easy adjusting the clamps position so that this
position matches with the rigging points.
Consult a professional structural engineer prior to suspending the ceiling mount from a structure not intended for that use. Always
ensure the working load limit of the structure supporting the projector.
Image 3-29
Mounting the clampsImage 3-30
Mounting the clamps
WARNING:When mounting the projector to the ceiling or to a rigging system, always mount security chains.
How to mount the clamps?
To fix the clamps to the U-profile, follow the next procedure :
1. Measure the distance, center tube as reference, between the two used support bars of a truss.
2. Slide the clamps holders (2 per profile) on its place in the U-profile according the measured distance and secure this position.
Image 3-31
Mounting the clamp — detail
3. Turn the overlockers in the holes of the clamp holder.
The overlocker can turn around.
How to mount the Overlockers to the truss?
To mount the overlocker to the truss, handle as follow :
1. Open the fixation handle.
30
R5976654 SLM R12+ 27/01/2005 
						

							3. Installation Guidelines
Image 3-32
Opening the rigging clamp
2. Hook the clamp around the tube.
The trigger automatically shuts the clamp.
3. Close the fixation handle and secure it by turning the hand screw.
Image 3-33
Closing the rigging clamp
R5976654 SLM R12+ 27/01/200531 
						

							3. Installation Guidelines
32R5976654 SLM R12+ 27/01/2005 
						

							4. Connections
4. CONNECTIONS
Overview
• Power connection
• Switching on
• Switching to standby
• Switching off
• Input Source Connections
• Communication Connections
4.1 Power connection
AC Power cord connection
Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector
at the left of the projector. The power input is 230 VAC.
Fuses
The projector is protected with an automatic circuit breaker of 15A which is built in into the power switch.
4.2 Switching on
How to switch on.
1. Press the power switch to switch on the projector.
- When ’0’ is visible, the projector is switched off.
- When ’1’ is visible, the projector is switched on
The projector starts in standby mode. The projector indication lamp is red.
Starting image projection.
1. PressStand bykey once on the local keypad or on the remote control.
The projector mode indication lamp will be green
-+
-
+
-+
-
+ -
+
09786
5
4
3
2 1
ENTER
32a
PAUSE-
+PHASE
FREEZTEXTEXIT
ADJ
STBY
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRASTHELP?
COLOR PHASE SHARPNTINT
BRIGHTN
STANDBY
ENTER
TEXTEXIT
PAUSE
2
14 3 5680
9
7CONTRAST
A
Image 4-1
Standby indication
Or,
Press a digit button to select an input source.
R5976654 SLM R12+ 27/01/2005
33 
						

							4. Connections
Lamp run time indication while running
When the total run time of the lamp is 30 hours less then 1000, the following warning message will be displayed for 1 minute. This
warning message will be repeated every 30 minutes. PressEXITto remove the message before the minute is over.
Remaining
Lamp run time
20h
Image 4-2
When the total run time of the lamp is 1000 hours or more, the following warning message, with the exact run time is displayed on
the screen.
WARNING
Lamp run time is x hours
operating the lamp longer
than x hours may damage
the projector.
Please replace the lamp
 to continue
Menu 4-1
Lamp run time is 1000 hours. Operating the lamp longer than maximum runtime hours may damage the projector. Please replace
the lamp.
WhenENTERis pressed to go on, the warning will be repeated every 30 min.
The total lifetime of the lamp for a safe operation is 1000 hours max. Do not use it longer. Always replace with a same type of lamp.
Call a BARCO authorized service technician for lamp replacement.
CAUTION:Using a lamp for more than 1000 hours is dangerous as the lamp could explode.
Lamp Light Output Indication
When starting up and the center lumens measurement is lower than 50 % of its initial value, the lamp light output warning will be
displayed. PressENTERto continue. The message will not be repeated during operation.
WARNING
Lamp run time is X hours
The light output of the lamp
is less
than 50% of its initial value.
It is advisable to replace the
lamp
before damage occurs.
 to confirm
Menu 4-2
When the ’Constant Light Output’ (CLO) options is installed, the light output message will appear on the screen when the light output
is reduced with 33% from its initial value.
This message will be repeated every hour.
Lamp Z-axis indication
When starting up and the run time is 100 hours or 250 hours a Z-axis warning will be displayed. This warning will advise to adjust the
Z-axis of the lamp to obtain maximum light output. PressENTERto continue. The message will not be repeated during operation.
WARNING
Lamp run time is X hours.
It is advisable to
adjust the Z-axis
of the lamp to
obtain maximum
light output
(see owner’s manual)
 to confirm
Menu 4-3
34R5976654 SLM R12+ 27/01/2005 
						

							4. Connections
4.3 Switching to standby
Howtoswitchtostandby?
1. PressStandbyto switch the projector to standby.
4.4 Switching off
How to switch off the projector?
1. Press firstStandby.
2. Let cool down the projector until the fans stop blowing, at least 15 min.
3. Switch off the projector with the power switch.
4.5 Input Source Connections
4.5.1 Input Facilities
Overview input facilities
OUT IN OnR9840450
HD SDI DIGITAL MODULE
OUT IN On9840110
SDI DIGITAL INPUT
COMM PORT10/(100)base-T
RS232/422 OUT
RS232/422 INIR-Receiver Diagnostic Code
Green Operation
Red Stand-by
IR Sync OK
Hardwired
remote
CTRL 1 Hardwired
remote
CTRL 2 Two way
hardwired
remote
CTRL 3
1234
OnOn
OnOn
DVI INPUT
DVI INPUT
DVI OUTPUT High Bandwidth  5 CABLE INPUT
High Bandwidth  5 CABLE INPUTRGBH/C V
RGBH/C V
Image 4-3
Input facilities
Input numberType of input
1Fixed input, 5 cable input or DVI input and DVI output
2Fixed input, 5 cable input or DVI input
3&4Variable inputs
Two digital inputs available.
• SDI input (R9840110)
• HD SDI Digital input (R9840450)
Digital Video Decoder (R9841170)
4.5.2 Inputs via RCVDS05
Overview
When using a RCVDS05, the input configuration must be as follows:
R5976654 SLM R12+ 27/01/2005
35 
						

							4. Connections
slot 1
RGB/Component
slot 2 Video
slot 3 not used
slot 4 not used
When using a RCVDS05, it is recommended to use a 5-cable output module in the RCVDS. The outputs of this module has to be
connected to slot 1 of the projector. To switch the projector in the 5-cable mode see Fixed slot (slot 1 & 2), page 37.
4.5.3 Input module insertion
How to insert an input module?
Toinsertamoduleinoneofthefreeslots,handleasfollow:
1. Power down the projector and disconnect the power cord from the wall outlet.
2. Remove the dummy plate covering the chosen input slot by turning out both screws.
3. Slide the input module in the free slot. Insure the module is seated correctly in the guide grooves.
4. Press on both handles of the input module until the module plug seats in the connector of the projector.
OUT IN OnR9840450
HD SDI DIGITAL MODULE
OUT IN On9840110
SDI DIGITAL INPUT
COMM PORT10/(100)BASE-T
RS232/422 OUT
RS232/422 INIR-Receiver Diagnostic Code
Green Operation
Red Stand-by
IR Sync OK
Hardwired
remote
CTRL 1 Hardwired
remote
CTRL 2 Two way
hardwired
remote
CTRL 3
DVI INPUT
DVI INPUTDVI OUTPUT High Bandwidth  5 CABLE INPUT
High Bandwidth  5 CABLE INPUT RGBH/C V
RGBV H/C
Image 4-4
5. Secure the input module by tightening both retaining screws.
6. Reconnect the power cord to the wall outlet and switch on the projector.
How to select the new installed module?
The new installed module can be selected with the digit buttons on the RCU or the local keypad.
36
R5976654 SLM R12+ 27/01/2005