Barco Slm R12+ Owners Manual

							7. Random Access Adjustment Mode
Example
Horizontal resolution source : 1600 pixels
horizontal resolution projector 1 & 2 : 1024 pixels
Overlap : 100 pixels
Total horizontal screen size in pixels : 1948 pixels
Pact projector 1 = [(1024 / 1948)] x 1600 = 841 pixels
Pact projector 2 = [(1024 / 1948)] x 1600 = 841 pixels
Pstart projector 2 = Pstart projector 1 + (1600 – 841)
7.5.6 ScenergiX overlap zone (vertical scenergix)
Definitions
Image 7-11
Scenergix overlap zone vertical
Overlap : number of pixels that overlap
Vertical resolution of 1 projector : 768 for Graphics versions, 1024 for Reality versions, 1050 for SXGA projectors.
Total vertical screen resolution : [(Vertical resolution of 1 projector) x 2] minus (overlap)
Vertical Resolution source : number of active lines of the source
Adjustment of Active lines (Lact) of the first projector
1. Go to File –> Edit menu of first projector.
2. Enter value for vertical act (= Lact) as follows :
Lact = [(vert.. resolution of 1 projector)/(Total Vert. screen resolution)] x (Verti. resolution source)
3. Vertical start (= Lstart) remains the same.
Adjustment of Active lines (Lact) of second projector
1. Go to File –> Edit menu of second projector.
2. Enter value for vertical act (= Lact) as follows :
Lact = [(Vert.. resolution of 1 projector)/(Total vert. screen resolution)] x (vert. resolution source)
3. Vertical start (= Lstart) = original start + [(Vert. resolution source) minus (newly calculated Lact)]
Example
Vertical resolution source : 1200 lines
Vertical resolution projector 1 & 2: 768 lines
Overlap : 50 lines
Total vertical screen size : 1486 lines
Lact projector 1 = (768 / 1486) x 1200 = 620 lines
Lact projector 2 = (768 / 1486/) x 1200 = 620 lines
R5976654 SLM R12+ 27/01/2005
87 
						

							7. Random Access Adjustment Mode
Lstart projector 2 = Lstart projector 1 + (1200 – 620)
7.5.7 ScenergiX size adjustment
What can be done with the ScenergiX size menu?
Within this menu the width of the blending zone is set up.
How to adjust the size?
Only accessible when the status is in the ON position.
1. Push the cursor key↑or↓to highlight one of the four size adjustments, Top, Bottom, Left or Right.
SCENERGIX
STATUS [ON]
- size -
TOP
BOTTOM
LEFT
RIGHT
- black level -
LEVEL
Select with↑or↓
then 
 to return
Menu 7-51
2. PressENTERto select.
A pattern with the different areas will be displayed.
Image 7-12
Width selections
3. Use the cursor keys to move the border of the overlap area to the desired position (value between 0 and 255).
Set first the width of the first projector and repeat for the second one.
88
R5976654 SLM R12+ 27/01/2005 
						

							7. Random Access Adjustment Mode
Image 7-13
Width set up for projector 1
Image 7-14
Width set up for projector 2
7.5.8 Adjusting the black level of the images
Why
For dark images, the overlap zone will be brighter then the rest of the images. Therefore we can rise the black level of the remaining
image (excluding the overlap zone).
How to adjust?
1. Push the cursor key↑or↓to highlightLevel.
SCENERGIX
STATUS [ON]
- size -
TOP
BOTTOM
LEFT
RIGHT
- black level -
LEVEL
Select with↑or↓
then 
 to return
Menu 7-52
2. PressENTERto activate.
3. Adjust the black level of area A until the black level of area A, B and C are equal.
R5976654 SLM R12+ 27/01/2005
89 
						

							7. Random Access Adjustment Mode
ACB
12
13
11R
G
BRGB
Image 1Image 2
Image 7-15
Black level adjustment
7.6 Picture in Picture (PiP)
Overview
• Introduction to PiP
• Picture in Picture activation
• Picture in Picture source
• Position of Picture in Picture window
• Set up of the Quick Selection
7.6.1 Introduction to PiP
PiP
PiP stands for Picture in Picture and allows to display multiple windows containing each of them an image. The
windows may be of the video or data type.
What are the different possibilities within the PiP mode ?
The input section of the SLM projector allows a combinations of different input signals which may be projected in the 2 windows of
the PiP screen. The PiP window can be placed in one of the four corners of the main window.
90
R5976654 SLM R12+ 27/01/2005 
						

							7. Random Access Adjustment Mode
Image 7-16
Possible position for PiP
7.6.2 Picture in Picture activation
How to activate PIP?
1. Push the cursor key↑or↓to highlightPIP.
RANDOM ACCESS
ADJUSTMENT MODE
FILE SERVICE
PICTURE TUNING
GEOMETRY
SCENERGIX
PIP
SAVE CHANGES
Select with↑or↓
then 
 to return
Menu 7-53
2. PressENTERto select.
The PIP menu will be displayed.
PIP
STATUS [ON]
SOURCE 01
POSITION [Top-Left]
QUICK SELECT [OFF]
Select with↑or↓
then 
 to return
Menu 7-54
3. Push the cursor key↑or↓to highlightStatus.
4. PressENTERto toggle between ON and OFF.
ONPIP is active
OFFPIP is not active
R5976654 SLM R12+ 27/01/2005
91 
						

							7. Random Access Adjustment Mode
7.6.3 Picture in Picture source
Which source displayed in PiP
1. Push the cursor key↑or↓to highlightSource.
PIP
STATUS [ON]
SOURCE 01
POSITION [Top-Left]
QUICK SELECT [OFF]
Select with↑or↓
then 
 to return
Menu 7-55
2. PressENTERto select.
3. Enter the source number with the remote control. Start always with 0.
7.6.4 Position of Picture in Picture window
What can be done?
The PiP window can be placed in on of the four corners of the main window.
How to position?
1. Push the cursor key↑or↓to highlightPosition.
PIP
STATUS [ON]
SOURCE 01
POSITION [Top-Left]
QUICK SELECT [OFF]
Select with↑or↓
then 
 to return
Menu 7-56
2. PressENTERto toggle betweenTop-Left,Top-Right,Bottom-LeftorBottom-Right.
7.6.5 Set up of the Quick Selection
What is possible?
When the quick selection is active, the source inside the PiP window can be switched to another source by entering on the RCU or
local keypad first 0 followed immediately by the source number. E.g. for source 2 in the PiP window, enter 02 on the RCU.
How to set
1. Push the cursor key↑or↓to highlightQuick Select.
PIP
STATUS [ON]
SOURCE 01
POSITION [Top-Left]
QUICK SELECT [OFF]
Select with↑or↓
then 
 to return
Menu 7-57
2. PressENTERto toggle between [OFF] and [].
OFF : no quick selection allowed.
 : quick selection allowed by using 0 before the source number.
92
R5976654 SLM R12+ 27/01/2005 
						

							7. Random Access Adjustment Mode
7.7 Save Changes
What can be done
The system saves automatically the changes every x minutes. When you want to save it quicker, use the save changes option.
How to save
1. Push the cursor key↑or↓to highlightSave Changes.
RANDOM ACCESS
ADJUSTMENT MODE
FILE SERVICE
PICTURE TUNING
GEOMETRY
SCENERGIX
PIP
SAVE CHANGES
Select with↑or↓
then 
 to return
Menu 7-58
2. PressENTERto save the actual settings in the active file.
A message will be displayed to wait a few second while the system is saving the data.
Message
Saving data
please wait
Menu 7-59
R5976654 SLM R12+ 27/01/200593 
						

							7. Random Access Adjustment Mode
94R5976654 SLM R12+ 27/01/2005 
						

							8. Installation Mode
8. INSTALLATION MODE
Overview
• Start up of the Installation mode
• Input Slots
• 800 peripheral
• Source Switching
•NoSignal
• Contrast Enhancement
• Convergence
• Configuration
• Lens Adjustment
• Quick Access Keys
•OSD
• Internal Patterns
8.1 Start up of the Installation mode
Start up
1. Push the cursor key↑or↓to highlightInstallation.
ADJUSTMENT MODE
Select a path from below :
RANDOM ACCESS
INSTALLATION
SERVICE
Select with↑or↓
then 
 to return
Menu 8-1
2. PressENTER.
The Installation mode menu will be displayed.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
SOURCE SWITCHING
NO SIGNAL
CONTRAST ENHANCEMENT
CONVERGENCE
CONFIGURATION
LENS
QUICK ACCESS KEYS
OSD
INTERNAL PATTERNS
Select with↑or↓
then 
 to return
Menu 8-2
8.2 Input Slots
What can be done ?
The input configuration of the variable inputs is shown in theInput slotsmenu.
R5976654 SLM R12+ 27/01/2005
95 
						

							8. Installation Mode
To view or the change the input configuration.
1. Push the cursor key↑or↓to highlightInput Slots.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
SOURCE SWITCHING
NO SIGNAL
CONTRAST ENHANCEMENT
CONVERGENCE
CONFIGURATION
LENS
QUICK ACCESS KEYS
OSD
INTERNAL PATTERNS
Select with↑or↓
then 
 to return
Menu 8-3
2. PressENTERto select.
The input slots menu will be displayed.
INPUT SLOTS
Slot Module type [config]
1. RGB-SS [CV]
2. RGB-SOG
3. SDI
4. SDI
______________
1. DVI OUTPUT [DVI input]
Select with↑or↓
then 
 to return
Menu 8-4
Possible results for the fixed input slots (1&2).
SourceIndication
Video or S-VideoVideo
S-video
RGB analogRGB-SS[CV] : separate sync is composite video on H/C input
RGB-SS[cS or HS&VS]: separate sync is composite sync or horizontal and vertical sync
RGB-SOG : sync on green
Component VideoComponent video - SS : Component video with separate sync
Component video - SOY : Component video with sync on Y
Component video - 3LSS : Component video with 3 level separate sync.
Component video - 3LSOY : Component video with 3 level syns on Y.
RGB analog with
tri-level-syncRGB-SS[3LSS] : RGB with separate Tri level sync.
RGB3L-SOG[3LSOY]: RGB with Tri-level sync on green.
DVIDVI
Possible results for input 3 and 4
SDISerial digital input
HD SDIhigh definition digital input
Digital Video DecoderVIDEO[VIDEO]
VIDEO[S-VIDEO]
VIDEO[YUV]
What if a switcher is connected to the projector ?
If a RCVDS (switched on) or VS05 is connected to the projector, it will be also indicated on the menu by adding +800 peripheral.
96
R5976654 SLM R12+ 27/01/2005