Barco Slm R12+ Owners Manual

							8. Installation Mode
If no 800 peripheral indication is made on the menu, there are still two possibilities, no RCVDS or VS05 connected or RCVDS is
switched off.
When a 800 peripheral is connected to the projector, the input slots are not accessible with the cursor key to toggle their function.
8.3 800 peripheral
Overview
• Defining the output module of the RCVDS05.
• Defining the Infrared Communication protocol
• CLO using Comm 800
8.3.1 Defining the output module of the RCVDS05.
Which module are available?
When a RCVDS05 is connected to the projector, the type of outputmodule of this RCVDS05 has to be defined in the 800 peripheral
menu.
• standard output module
• 5 cable output module
Defining the output module
To define the output module:
1. Push the cursor key↑or↓to highlight800 Peripheral.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
SOURCE SWITCHING
NO SIGNAL
CONTRAST ENHANCEMENT
CONVERGENCE
CONFIGURATION
LENS
QUICK ACCESS KEYS
OSD
INTERNAL PATTERNS
Select with↑or↓
then 
 to return
Menu 8-5
2. PressENTERto select.
3. Push the cursor key↑or↓to highlightOutput module.
800 PERIPHERAL
OUTPUT MODULE [STANDARD]
CLO USING COMM800 [YES]
INFRARED [PPM]
Select with↑or↓
then 
 to return
Menu 8-6
8.3.2 Defining the Infrared Communication protocol
Which protocols are available?
When a peripheral is connected to the ’Comm Port’, the communication can be in PPM or RC5.
The type of communication can be set to :
•PPM
• RC5
R5976654 SLM R12+ 27/01/2005
97 
						

							8. Installation Mode
Defining the communication protocol.
1. Push the cursor key↑or↓to highlight800 Peripheral.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
SOURCE SWITCHING
NO SIGNAL
CONTRAST ENHANCEMENT
CONVERGENCE
CONFIGURATION
LENS
QUICK ACCESS KEYS
OSD
INTERNAL PATTERNS
Select with↑or↓
then 
 to return
Menu 8-7
2. PressENTERto select.
3. Push the cursor key↑or↓to highlightInfrared.
800 PERIPHERAL
OUTPUT MODULE [STANDARD]
CLO USING COMM800 [YES]
INFRARED [PPM]
Select with↑or↓
then 
 to return
Menu 8-8
4. PressENTERto select.
5. PressENTERto toggle between [PPM] or [RC5].
8.3.3 CLO using Comm 800
What can be done?
CLO can be activated in a linked system setup using the COM800 Protocol + Ports.
By using the COM800 Protocol + Ports, the RS232 Ports can be used for a RS232 linked setup, CLO is received
through the COM800 Ports, general RS232 commands are received through the RS232 Ports.
How to change the COM800 Protocol Activation?
1. Push the cursor key↑or↓to highlightCLO using COM800: [NO].
800 PERIPHERAL
OUTPUT MODULE [STANDARD]
CLO USING COMM800 [YES]
INFRARED [PPM]
Select with↑or↓
then 
 to return
Menu 8-9
2. PressENTERto toggle between [NO] or [YES].
[No]
CLO will not use Comm800 protocol
[Yes]
CLO will use Comm800 protocol
98
R5976654 SLM R12+ 27/01/2005 
						

							8. Installation Mode
8.4 Source Switching
Switching from one source to another.
To minimize undesired effects when switching from one source to another one can use the Seamless switching mode, beside Seam-
less switching there is a choice between several effects which render the transitions more enjoyable.
How to select a switching mode
1. Push the cursor key↑or↓to highlightSource Switching.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
SOURCE SWITCHING
NO SIGNAL
CONTRAST ENHANCEMENT
CONVERGENCE
CONFIGURATION
LENS
QUICK ACCESS KEYS
OSD
INTERNAL PATTERNS
Select with↑or↓
then 
 to return
Menu 8-10
2. PressENTERto select.
The seamless source switching menu will be displayed.
SEAMLESS
SOURCE SWITCHING
EFFECT [NO TRANSITION]
 to toggle
 to return.
Menu 8-11
3. PressENTERto toggle between [NO TRANSITION], [FADE], ...
OFF no effect installed.
RANDOM TRANSITION source switching will happens with an effect, random chosen between the available effects.
Image 8-1
Example of seamless switching with Fade effect.
When an effect is selected within seamless source switching, wait until the effect is terminated before switch-
ing to another source (± 2 seconds).
8.5 No Signal
Overview
• Changing the Background Color
• Changing the Shutdown Setting
• Changing the Shutdown Time
R5976654 SLM R12+ 27/01/2005
99 
						

							8. Installation Mode
8.5.1 Changing the Background Color
How to change ?
1. Push the cursor key↑or↓to highlightNo signal.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
SOURCE SWITCHING
NO SIGNAL
CONTRAST ENHANCEMENT
CONVERGENCE
CONFIGURATION
LENS
QUICK ACCESS KEYS
OSD
INTERNAL PATTERNS
Select with↑or↓
then 
 to return
Menu 8-12
2. PressENTERto select.
The no signal menu will be displayed.
NO SIGNAL
COLOR [Blue]
SHUTDOWN [off]
Shutdown time: 5 min
Select with↑or↓
then 
 to return
Menu 8-13
3. Push the cursor key↑or↓to highlightColor.menu 8-13
4. PressENTERto toggle between [blue] or [black].
8.5.2 Changing the Shutdown Setting
How to change ?
1. Push the cursor key↑or↓to highlightNo Signal.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
SOURCE SWITCHING
NO SIGNAL
CONTRAST ENHANCEMENT
CONVERGENCE
CONFIGURATION
LENS
QUICK ACCESS KEYS
OSD
INTERNAL PATTERNS
Select with↑or↓
then 
 to return
Menu 8-14
2. PressENTERto select.
The no signal menu will be displayed.
NO SIGNAL
COLOR [Blue]
SHUTDOWN [off]
Shutdown time: 5 min
Select with↑or↓
then 
 to return
Menu 8-15
3. Push the cursor key↑or↓to highlightShutdown.menu 8-15
100
R5976654 SLM R12+ 27/01/2005 
						

							8. Installation Mode
4. PressENTERto toggle between [On] or [Off].
8.5.3 Changing the Shutdown Time
Range
The shutdown time can be set between 5 min. and 60 min.
How to change ?
To set up the shutdown time, handle as follow:
1. Push the cursor key↑or↓to highlightNo Signal.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
SOURCE SWITCHING
NO SIGNAL
CONTRAST ENHANCEMENT
CONVERGENCE
CONFIGURATION
LENS
QUICK ACCESS KEYS
OSD
INTERNAL PATTERNS
Select with↑or↓
then 
 to return
Menu 8-16
2. PressENTERto select.
The no signal menu will be displayed.
NO SIGNAL
COLOR [Blue]
SHUTDOWN [off]
Shutdown time: 5 min
Select with↑or↓
then 
 to return
Menu 8-17
3. Push the cursor key↑or↓to highlightShutdown Time.menu 8-17
4. Push the cursor key↑or↓to change the digits.
Or,
Enter the digits directly with the digit keys on the RCU.
8.6 Contrast Enhancement
Purpose
Increases contrast for all video and data sources.
Contrast enhancement will reduce the light output of the projector.
R5976654 SLM R12+ 27/01/2005101 
						

							8. Installation Mode
To change the Contrast Enhancement value
1. Push the cursor key↑or↓to highlightContrast Enhancement.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
SOURCE SWITCHING
NO SIGNAL
CONTRAST ENHANCEMENT
CONVERGENCE
CONFIGURATION
LENS
QUICK ACCESS KEYS
OSD
INTERNAL PATTERNS
Select with↑or↓
then 
 to return
Menu 8-18
2. PressENTERto select.
The contrast enhancement menu will be displayed.
CONTRAST ENHANCEMENT
NORMAL CONTRAST
HIGH CONTRAST
Select with↑or↓
then 
 to return
Menu 8-19
3. Push the cursor key↑or↓to highlight the desired contrast enhancement, normal or high.
4. PressENTERto select.
A timer will countdown from 45 seconds to 0. During this time, no action maybe undertaken. The projector is switching the
contrast setting and has to recalculate the internal settings.
CONTRAST ENHANCEMENT
NORMAL CONTRAST
HIGH CONTRAST
Remaining time : 44 sec
Select with↑or↓
then 
 to return
Menu 8-20
8.7 Convergence
What can be done?
The convergence of the displayed image can be adjusted only by a qualified service technician.
How to start up?
1. Push the cursor key↑or↓to highlightConvergence.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
SOURCE SWITCHING
NO SIGNAL
CONTRAST ENHANCEMENT
CONVERGENCE
CONFIGURATION
LENS
QUICK ACCESS KEYS
OSD
INTERNAL PATTERNS
Select with↑or↓
then 
 to return
Menu 8-21
102R5976654 SLM R12+ 27/01/2005 
						

							8. Installation Mode
2. PressENTERto select.
The following message will be displayed : “Convergence is reserved to qualified service personnel.”
WARNING
CONVERGENCE
is reserved to
qualified
service personnel
 to accept
 to return
Menu 8-22
8.8 Configuration
What can be done?
The way of physical installation of the projector can be defined to the projector.
The following installation configurations are possible:
• front/table
• front/ceiling
• rear/table
• rear/table
Set up the Correct Configuration
1. Push the cursor key↑or↓to highlightConfiguration.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
SOURCE SWITCHING
NO SIGNAL
CONTRAST ENHANCEMENT
CONVERGENCE
CONFIGURATION
LENS
QUICK ACCESS KEYS
OSD
INTERNAL PATTERNS
Select with↑or↓
then 
 to return
Menu 8-23
2. PressENTERto select.
The configuration menu will be displayed.
For more information, see Installation Guidelines .
8.9 Lens Adjustment
What can be done ?
All lens adjustments are motorized and can be adjusted with the RCU.
The following items can be adjusted:
• zoom/focus
•shift
• Options : same zoom/focus for all files, yes or no.
R5976654 SLM R12+ 27/01/2005
103 
						

							8. Installation Mode
How to start up.
1. Push the cursor key↑or↓to highlightLens.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
SOURCE SWITCHING
NO SIGNAL
CONTRAST ENHANCEMENT
CONVERGENCE
CONFIGURATION
LENS
QUICK ACCESS KEYS
OSD
INTERNAL PATTERNS
Select with↑or↓
then 
 to return
Menu 8-24
2. PressENTERto select.
The lens menu will be displayed.
LENS ADJUSTMENT
ZOOM/FOCUS
SHIFT
OPTIONS
Select with↑or↓
then 
 to return
Menu 8-25
How to Zoom/Focus ?
1. Push the cursor key↑or↓to select Zoom/Focus.
LENS ADJUSTMENT
ZOOM/FOCUS
SHIFT
OPTIONS
Select with↑or↓
then 
 to return
Menu 8-26
2. Push the cursor key↑or↓to zoom and←or→to focus the image.see Quick Set Up Adjustments, page 50
3. When finished, pressEXITto return to the lens adjustment menu or pressENTERto go to the shift function.
Press the selection key * to switch to another pattern. Different patterns are available.
How to shift the image?
1. When on the Zoom/Focus menu, pressENTERto switch to the shift menu or
2. When on the Lens Adjustment menu, Push the cursor key↑or↓to highlightShiftand press ENTER to display the shift menu.
LENS ADJUSTMENT
ZOOM/FOCUS
SHIFT
OPTIONS
Select with↑or↓
then 
 to return
Menu 8-27
104R5976654 SLM R12+ 27/01/2005 
						

							8. Installation Mode
3. Push the cursor key↑or↓to shift the image up or down and←or→to shift the image left or right.
4. When finished, pressEXITto go to the lens adjustment menu or pressENTERto go to the zoom/focus function.
Press the selection key * to switch to another pattern. Different patterns are available.
Options
The zoom/focus and shift can be set the same for all files.
1. Push the cursor key↑or↓to highlightOptions.
LENS ADJUSTMENT
ZOOM/FOCUS
SHIFT
OPTIONS
Select with↑or↓
then 
 to return
Menu 8-28
2. PressENTERto select.
The Lens Options menu will be displayed.
LENS OPTIONS
Use the same
zoom and focus
of the lens
for all files?
[No]
 to toggle
 to return.
Menu 8-29
3. PressENTERto toggle between ’Yes’ or ’No’.
[Yes]
all lens settings will be the same for all files
[No]
different lens settings for all files
Default setting : [Yes]
When in the ’No’ position, the lens memory is using incremental motors which have an accuracy of 1 to 2
steps. This has no implication for zoom, but focus might demand some fine-tuning when switching from one
source to another.
8.10 Quick Access Keys
What can be done?
It is possible to get an overview of the programmed functions of the different function keys (only accessible with an adapted RCU).
R5976654 SLM R12+ 27/01/2005
105 
						

							8. Installation Mode
How to get an overview.
1. Push the cursor key↑or↓to highlightQuick Access Keys.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
SOURCE SWITCHING
NO SIGNAL
CONTRAST ENHANCEMENT
CONVERGENCE
CONFIGURATION
LENS
QUICK ACCESS KEYS
OSD
INTERNAL PATTERNS
Select with↑or↓
then 
 to return
Menu 8-30
2. PressENTERto select.
The Quick Access Overview menu will be displayed.
QUICK ACCESS KEYS
 :
 :
 :
 :
 :
 : LENS ADJUSTMENTS
 : PiP SOURCE
CLEAR ALL
Select with↑or↓
then 
 to return.
Menu 8-31
 starts up the lens adjustment functions
 0 keys is used as prefix when selecting a PiP source. E.g. 0 + 2 will select source 2 as PiP source while only 2 will select
source 2 as main source.
No functions are preprogrammed.
8.11 OSD
Overview
• Color Settings
• Menu Position
8.11.1 Color Settings
How to change
1. Push the cursor key↑or↓to highlightOSD.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
SOURCE SWITCHING
NO SIGNAL
CONTRAST ENHANCEMENT
CONVERGENCE
CONFIGURATION
LENS
QUICK ACCESS KEYS
OSD
INTERNAL PATTERNS
Select with↑or↓
then 
 to return
Menu 8-32
2. PressENTERto select.
106
R5976654 SLM R12+ 27/01/2005