Barco Slm R12+ Owners Manual

							3. Installation Guidelines
3.5.1 Access to the Lamp Unit.
What has to be done
To access the lamp casing, a side panel has to be removed.
Necessary tools
A flatblade screwdriver of 5 mm
Removingthesidepanel
1. Turn with a screwdriver the side panel lockscrew (A) a quarter turn counter clockwise.
A
Image 3-7
Unlocking the side cover
2. Pull the right side of the panel towards you and next to the rightto remove.
AB
Image 3-8
Lamp cover removal
3.5.2 Installation of the new Lamp Unit.
What has to be done
First remove the lock nut oneach spacer screw and next slide the lamp unit into the projector frame.
Necessary tools
Flatblade screwdriver of 5mm or Nut driver 8mm
R5976654 SLM R12+ 27/01/2005
17 
						

							3. Installation Guidelines
Installing the lamp unit
1. Remove the lock nut (B) on the 3 spacer screws (A).
B
A
Image 3-9
2. Line up the lamp unit guides (A) with the guides on the projector base (B) and push the unit into the frame until it fits.
B
A
Image 3-10
Lamp unit mounting
3. Secure the position of the lamp unit with the 3 spacer screws.
18
R5976654 SLM R12+ 27/01/2005 
						

							3. Installation Guidelines
A
A
A
Image 3-11
Lamp unit fixation
3.5.3 Reinstalling the Side Panel
What has to be done
After the new lamp unit has been installed, the side panel has to be remounted.
Necessary tools
A flatblade screwdriver of 5 mm
Reinstalling the side panel
1. Move the cover guides under the back cover and push the front of the cover against the projector frame lining up the cover lock
screw with the speed nut (A) on the frame.
Image 3-12
Mounting the side cover
Image 3-13
Closing the side cover
2. Turn with a screwdriver the side panel lock screw (B) a quarter turn clockwise to lock.
R5976654 SLM R12+ 27/01/2005
19 
						

							3. Installation Guidelines
B
Image 3-14
Locking side panel
3.6 Realignment of the lamp in its reflector
WARNING:As the projector has to be opened, this procedure has to be performed by qualified service tech-
nician.
Why
With higher run times, the light output of the lamp will decrease, which results in a lower light output on the screen. This light output
decrease can be compensated by readjusting the position of the lamp.
A suggestion dialog box will be displayed when the projector is restarted after 100 hours and 250 hours. OnceENTERis pressed
when that box is open, this box will not be displayed again till the next alert point is reached.
Suggestion
Lamp runtime is
105 hours
It is advisable to
adjust the Z-axis
of the lamp to
obtain maximum
light output
(see owners manual)
 to confirm
Menu 3-1
The user can now adjust the Z-axis by following the next procedure.
How to readjust.
1. On the side of the inputs, turn the captive screw a quarter counter clockwise.
2. Flip the cover to the left side and take off.
20
R5976654 SLM R12+ 27/01/2005 
						

							3. Installation Guidelines
Image 3-15
Lamp adjustment access
3. Start up the adjustment mode and selectService.
ADJUSTMENT MODE
Select a path from below :
RANDOM ACCESS
INSTALLATION
SERVICE
Select with↑or↓
then 
 to return
Menu 3-2
4. Select Lamp. The Z-axis value indication (lamp menu in service mode) will be helpful while turning screw B .
SERVICE
IDENTIFICATION
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJ. ADDRESS
SERIAL COMMUNICATION
NETWORK
LAMP
DIMMING
MORE...
Select with↑or↓
then 
 to return
Menu 3-3
LAMP
Constant Light output [OFF]
Using [RS port]
Mode [NORMAL]
Serial number : R101111
Article number : R9840xxx
Run time : 10 hours
Remaining run time : 490
hours
Number of strikes : 10
Z_AXIS : 100
Select with↑or↓
then 
 to return.
Menu 3-4
5. Loosen the lock nut A, securing the position of the adjustable screw (B), on the back of the lamp casing (nutdriver 10).
R5976654 SLM R12+ 27/01/2005
21 
						

							3. Installation Guidelines
A
Image 3-16
Lamp Z-Axis alignment (Former lamp house)
B
A
Image 3-17
Lamp Z-Axis alignment (Universal lamp house)
6. Slowly turn the screw B (image 3-16, , image 3-17, using an Allenkeyof3mm,alittleclockwiseuntilthemaximumvalueofthe
Z-AXIS indication in the lamp menu is reached.
7. Tighten the lock nut on the adjustable screw to secure its position (nutdriver 10).
CAUTION:Never turn the other screws ! These are factory aligned.
22R5976654 SLM R12+ 27/01/2005 
						

							3. Installation Guidelines
3.7 Lenses
Overview
• Lenses
• Lens selection
• Lens formulas
• Lens Installation
• Cleaning the lens
3.7.1 Lenses
Available lenses
TLD(1.6–2.0:1)R9840670
TLD(2.0–2.8:1)R9840680
TLD(2.8–5.0:1)R9840690
TLD(1.2:1)R9840770
TLD(0.8:1)R9840900
TLD(5.0–8.0:1)R9840910
TLD HB(0.8:1)R9842040
TLD HB(1.6–2.0:1)R9842060
TLD HB(2.0–2.8:1)R9842080
TLD HB(2.8–5.0:1)R9842100
TLD HB(5.0–8.0:1)R9842120
3.7.2 Lens selection
How to select ?
1. Determine the required screen width.
2. Determine the approximate position of the projector in the projection room with regard to the screen and measure the projector-
screen distance (PD).
3. Use the lens formulas to find the best corresponding PD with regard to the measured projector-screen distance for the required
screen width.
3.7.3 Lens formulas
Formulas for the standard TLD HB lenses
Metric formulas (meter)Inch formulas (inch)
TLD HB(0.8:1)PD=0.77xSW+0.05PD=0.77SW+1.97
TLD HB(1.2:1)PD=1.11xSW-0.01PD=1.11xSW-0.39
TLD HB(1.6–2.0:1)PDmin=1.47xSW-0.09
PD
max=1.85xSW-0.13
PDmin=1.47xSW-3.54
PD
max=1.85xSW-5.12
TLD HB(2.0–2.8:1)PDmin=1.85xSW-0.17
PD
max=2.62xSW-0.24
PDmin=1.85xSW-6.69
PD
max=2.62xSW-9.45
TLD HB(2.8–5.0:1)PDmin=2.58xSW-0.16
PD
max=4.71xSW-0.38
PDmin=2.58xSW-6.30
PD
max=4.71xSW-14.96
TLD HB(5.0–8.0:1)PDmin=4.52xSW-0.01
PD
max=7.53xSW-0.29
PDmin=4.52xSW-0.39
PD
max=7.53xSW-11.42
R5976654 SLM R12+ 27/01/200523 
						

							3. Installation Guidelines
Formulas for TLD lenses
Metric formulas (meter)Inch formulas (inch)
TLD(0.8:1)PD=0.77xSW+0.05PD=0.77SW+1.97
TLD(1.2:1)PD=1.11xSW-0.01PD=1.11xSW-0.39
TLD(1.6–2.0:1)PDmin=1.47xSW-0.09
PD
max=1.85xSW-0.13
PDmin=1.47xSW-3.54
PD
max=1.85xSW-5.12
TLD(2.0–2.8:1)PDmin=1.85xSW-0.17
PD
max=2.62xSW-0.24
PDmin=1.85xSW-6.69
PD
max=2.62xSW-9.45
TLD(2.8–5.0:1)PDmin=2.58xSW-0.16
PD
max=4.71xSW-0.38
PDmin=2.58xSW-6.30
PD
max=4.71xSW-14.96
TLD(5.0–8.0:1)PDmin=4.52xSW-0.01
PD
max=7.53xSW-0.29
PDmin=4.52xSW-0.39
PD
max=7.53xSW-11.42
3.7.4 Lens Installation
How to install ?
Follow the next procedure:
1. Remove the foam rubber in the opening of the lens holder.
2. Take the lens assembly out of its packing material and remove the lens caps on both sides.
3. Move the handle (A) of the lens anchor system to the right.
Image 3-18
Lens installation
4. Push the lens, motors at the top, in the lens block gap horizontally, lining up the motor connector on the lens with the connector
on the lens block (B), until the lens clicks in the lens anchor system.
24
R5976654 SLM R12+ 27/01/2005 
						

							3. Installation Guidelines
Image 3-19
Mounted Lens
Caution:On a table mounted projector, hold the projector when pushing the lens into the lens blockto avoid sliding off from
the table.
3.7.5 Cleaning the lens
To minimize the possibility of damaging the optical coating or scratching exposed lens surface, we have de-
veloped recommendations for cleaning the lens. FIRST, we recommend you try to remove any material from
the lens by blowing it off with clean, dry deionized air. DO NOT use any liquid to clean the lenses.
Necessary tools
To r a y s e eTMcloth (delivered together with the lens kit). Order number : R379058.
Howtocleanthelens?
Proceed as follow :
1. Always wipe lenses with a CLEAN Toraysee
TMcloth.
2. Always wipe lenses in a single direction.
Warning:Do not wipe back and forwards across the lens surface as thistends to grind dirt into the coating.
3. Do not leave cleaning cloth in either an open room or lab coat pocket, as doing so can contaminate the cloth.
4. If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a dirty cloth.
WARNING:Do not use fabric softener when washing the cleaning cloth or softener sheets when drying the
cloth.
Do not use liquid cleaners on the cloth as doing so will contaminate the cloth.
CAUTION:Other lenses can also be cleaned safely with this TorayseeTMcloth.
3.8 Battery Installation in the RCU
How is the battery delivered ?
The battery for the RCU is not yet installed on delivery, to save the battery life time, and is placed in the upper compartment (B)
inside the RCU (image 3-20).
Howtoplugin!
1. Press the battery cover (A) lock (1) inwards and simultaneously lift up the cover (2) for removal.
R5976654 SLM R12+ 27/01/2005
25 
						

							3. Installation Guidelines
1 2
A
B
Image 3-20
Battery cover removal
2. Plug in the battery (9 V battery - type E-block or equivalent) onto the battery contact plate (A).
A
B
Image 3-21
Battery connection
3. Place the battery into the lower compartment (B) (image 3-21).
4. Insert the pins of the battery cover (A) into the slots on the bottom of battery back cover and close the cover by pushing downwards
(B) until it clicks.
AB
Image 3-22
Battery cover mount
5. A card, containing a button preset overview, can be inserted behind the plastic windowpane on the battery cover.
26
R5976654 SLM R12+ 27/01/2005