Barco Slm R12+ Owners Manual

5. Getting Started
5. GETTING STARTED
5.1 RCU & Local keypad
How controlling the projector ?
The projector can be controlled by the local keypad or by the remote control unit.
Location of the local keypad ?
The local keypad is located on the input side of the projector.
Remote control functions.
This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely. This
remote control is used for source selection, control, adaptation andset up. It...

5. Getting Started
1Barco keyselection key, to get direct access to the lens adjustment menus.
2ADJADJUST key, to enter or exit the adjustment mode.
3Address key(recessed key), to enter the address of the projector (between 0 and 9). Press the
recessed address key with a pencil, followed by pressing one digit button between
0and9.
4STDYstand-by button, to start projector when the power switch is switched on and to switch
off the projector without switching off the power switch.
5PA U S Eto stop...

5. Getting Started
The projector mode indication lamp will be green
-+
-
+
-+
-
+ -
+
09786
5
4
3
2 1
ENTER
32a
PAUSE-
+PHASE
FREEZTEXTEXIT
ADJ
STBY
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRASTHELP?
COLOR PHASE SHARPNTINT
BRIGHTN
STANDBY
ENTER
TEXTEXIT
PAUSE
2
14 3 5680
9
7CONTRAST
A
Image 5-2Or,
Press a digit button to select an input source.
Lamp Run time indication
see chapter 4. Connections, Switching on, page 33
Lamp Light output indication
see chapter 4. Connections, Switching on, page 33
Lamp Z-axis...

5. Getting Started
ERROR
DMD out of operating
temperature
range
Automatic shutdown is
activated
Menu 5-1
5.4 Quick Set Up Adjustments
Overview
• Quick Language Change
• Quick Lens Adjustment
• Quick On Screen Color change
5.4.1 Quick Language Change
What can be done?
Only if different on screen languages are available, these can be changed in quick way by following the next procedure.
How to change
1. PressENTERto start up the adjustment mode.
2. Press the cursor key↑or↓to highlightService.
ADJUSTMENT...

5. Getting Started
6. Push the cursor key↑or↓to highlight the desired language.
CHANGE LANGUAGE
ENGLISH
Select with↑or↓
then 
 to return
Menu 5-4
Note:For the moment, only English is available.
5.4.2 Quick Lens Adjustment
Quick zoom/focus adjustment
1. Press the Selection key*, Barco key.
The zoom/focus menu will be displayed.
LENS ADJUSTMENT ZOOM/FOCUS
ZOOM with     or     ,
FOCUS with       or 
 to shift
 to return
Image 5-3
2. Push the cursor key↑or↓to zoom and←or→to focus the image.
3. When finished,...

5. Getting Started
Press the selection key * to switch to another pattern. Different patterns are available.
5.4.3 Quick On Screen Color change
What can be done ?
For quick change of the on-screen color of the highlighted items.
The highlighted items on the menus can be displayed in red, green or yellow.
How to change ?
1. PressENTERto start up the adjustment mode.
2. Push the cursor key↑or↓to highlightInstallation.
ADJUSTMENT MODE
Select a path from below :
RANDOM ACCESS
INSTALLATION
SERVICE
Select...

5. Getting Started
5.5 Using the RCU
Pointing to the reflective screen
1. Point the front of the RCU to the reflective screen surface.
Ceiling
ScreenIR sensor
RCU
Image 5-5
Hardwired Remote Input
1. Plug one end of the remote cable in the connector on the bottom of the RCU.
2. Plug the other end in the connector in the front panel of the projector labelledRC.
OUT IN OnR9840450
HD SDI DIGITAL MODULE
OUT IN On9840110
SDI DIGITAL INPUT
COMM PORT10/(100) BASE-T
RS232/422 OUT
RS232/422 INIR-Receiver...

5. Getting Started
Hardwired to the XLR input
1. Plug one end of the remote cable in the connector on the bottom of the RCU
2. Plug the other end in the connector in the front panel of the projector labelledHardwired CTRL2.
OUT IN OnR9840450
HD SDI DIGITAL MODULE
OUT IN On9840110
SDI DIGITAL INPUT
COMM PORT10/(100)BASE-T
RS232/422 OUT
RS232/422 INIR-Receiver Diagnostic Code
Green Operation
Red Stand-by
IR Sync OK
Hardwired
remote
CTRL 1 Hardwired
remote
CTRL 2 Two way
hardwired
remote
CTRL 3
OnOn
OnOn...

5. Getting Started
A DDRADJ EXITSTBY MUTE TEXT
B RIGHTNES S-
+
-+
-+
-
+S HA RPNES S -+TINT
COL ORCONTRAST 
FREEZ09786 5
4
3
2 1
ENTER
RCU
Front of projector
IR sensor
A DDRADJ EXITSTBY MUTE TEXT
B RIGHTNES S-
+
-+
-+
-
+S HA RPNES S -+TINT
COL ORCONTRAST 
FREEZ09786 54 32 1
ENTER
RCU
Rear of projector
IR sensor
Table
45ø 45ø45ø 45ø
Side of projector
ADDRADJ EXITSTBYMU TE TEXT
BRIGHTNESS-
+
-+
-+
-
+S HA RPNES S -+TINT
COL ORCONTRAST 
FREEZ09786 54 32 1
ENTER
RCU
45ø 45ø
Image 5-8
5.6 Projector Address...

5. Getting Started
5.6.2 Displaying and Programming addresses
Displaying the Projector Address on the Screen.
1. PressAddresskey (recessed key on the RCU) with a pencil.
The projector’s address will be displayed in a ’Text box’
To continue using the RCU with that specific address, it is necessary to enter the same address with the
digit buttons (address between 0 and 9) within 5 seconds after pushing the address key. For example : if the
Address key displays projector address 003, then press 3 digit...