Barco Slm R12+ Owners Manual

3. Installation Guidelines
3.9 Stacking Projectors
What is possible?
Up to 3 projectors can be stacked on each other without using extra tools or accessories.
How to stack?
Handle as follow:
1. Put the second projector on the first one so that base plate of the second projector matches with the rigging socket of the first
projector.
Image 3-23
Stacking two projectors
2. Turn the rigging sockets of the second projector counter clockwise until they are free to move up and down.
Image 3-24
Closing the...

3. Installation Guidelines
A
Image 3-25
Mounting the security chain
5. Guide hook and cable around the carry handle and guide it around the carry handle of the upper projector.
Image 3-26
Mounting the security hook
6. Hook it in the foreseen hole B in the base plate of the upper projector.
28
R5976654 SLM R12+ 27/01/2005 

3. Installation Guidelines
CB
B
Image 3-27
Mounting the security hook (detail)
How to open a secured rigging point?
1. Push the ring (A) of the first projector downwards and hold it in that position.
A
B
Image 3-28
Opening the rigging sockets
2. Turn the locked part (B) of the second projector a quarter counter clockwise and move it upwards.
R5976654 SLM R12+ 27/01/2005
29 

3. Installation Guidelines
3.10 Rigging points and Accessories
Clamps
Slots are made in the carry handle frame for easy inserting the overlockers and for easy adjusting the clamps position so that this
position matches with the rigging points.
Consult a professional structural engineer prior to suspending the ceiling mount from a structure not intended for that use. Always
ensure the working load limit of the structure supporting the projector.
Image 3-29
Mounting the clampsImage 3-30
Mounting the...

3. Installation Guidelines
Image 3-32
Opening the rigging clamp
2. Hook the clamp around the tube.
The trigger automatically shuts the clamp.
3. Close the fixation handle and secure it by turning the hand screw.
Image 3-33
Closing the rigging clamp
R5976654 SLM R12+ 27/01/200531 

3. Installation Guidelines
32R5976654 SLM R12+ 27/01/2005 

4. Connections
4. CONNECTIONS
Overview
• Power connection
• Switching on
• Switching to standby
• Switching off
• Input Source Connections
• Communication Connections
4.1 Power connection
AC Power cord connection
Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector
at the left of the projector. The power input is 230 VAC.
Fuses
The projector is protected with an automatic circuit breaker of 15A which is built in into the power...

4. Connections
Lamp run time indication while running
When the total run time of the lamp is 30 hours less then 1000, the following warning message will be displayed for 1 minute. This
warning message will be repeated every 30 minutes. PressEXITto remove the message before the minute is over.
Remaining
Lamp run time
20h
Image 4-2
When the total run time of the lamp is 1000 hours or more, the following warning message, with the exact run time is displayed on
the screen.
WARNING
Lamp run time is x hours...

4. Connections
4.3 Switching to standby
Howtoswitchtostandby?
1. PressStandbyto switch the projector to standby.
4.4 Switching off
How to switch off the projector?
1. Press firstStandby.
2. Let cool down the projector until the fans stop blowing, at least 15 min.
3. Switch off the projector with the power switch.
4.5 Input Source Connections
4.5.1 Input Facilities
Overview input facilities
OUT IN OnR9840450
HD SDI DIGITAL MODULE
OUT IN On9840110
SDI DIGITAL INPUT
COMM PORT10/(100)base-T
RS232/422 OUT...

4. Connections
slot 1
RGB/Component
slot 2 Video
slot 3 not used
slot 4 not used
When using a RCVDS05, it is recommended to use a 5-cable output module in the RCVDS. The outputs of this module has to be
connected to slot 1 of the projector. To switch the projector in the 5-cable mode see Fixed slot (slot 1 & 2), page 37.
4.5.3 Input module insertion
How to insert an input module?
Toinsertamoduleinoneofthefreeslots,handleasfollow:
1. Power down the projector and disconnect the power cord from the wall...