Barco Slm R12+ Owners Manual

3. Installation Guidelines
3.5.1 Access to the Lamp Unit.
What has to be done
To access the lamp casing, a side panel has to be removed.
Necessary tools
A flatblade screwdriver of 5 mm
Removingthesidepanel
1. Turn with a screwdriver the side panel lockscrew (A) a quarter turn counter clockwise.
A
Image 3-7
Unlocking the side cover
2. Pull the right side of the panel towards you and next to the rightto remove.
AB
Image 3-8
Lamp cover removal
3.5.2 Installation of the new Lamp Unit.
What has to be done...

3. Installation Guidelines
Installing the lamp unit
1. Remove the lock nut (B) on the 3 spacer screws (A).
B
A
Image 3-9
2. Line up the lamp unit guides (A) with the guides on the projector base (B) and push the unit into the frame until it fits.
B
A
Image 3-10
Lamp unit mounting
3. Secure the position of the lamp unit with the 3 spacer screws.
18
R5976654 SLM R12+ 27/01/2005 

3. Installation Guidelines
A
A
A
Image 3-11
Lamp unit fixation
3.5.3 Reinstalling the Side Panel
What has to be done
After the new lamp unit has been installed, the side panel has to be remounted.
Necessary tools
A flatblade screwdriver of 5 mm
Reinstalling the side panel
1. Move the cover guides under the back cover and push the front of the cover against the projector frame lining up the cover lock
screw with the speed nut (A) on the frame.
Image 3-12
Mounting the side cover
Image 3-13
Closing the side...

3. Installation Guidelines
B
Image 3-14
Locking side panel
3.6 Realignment of the lamp in its reflector
WARNING:As the projector has to be opened, this procedure has to be performed by qualified service tech-
nician.
Why
With higher run times, the light output of the lamp will decrease, which results in a lower light output on the screen. This light output
decrease can be compensated by readjusting the position of the lamp.
A suggestion dialog box will be displayed when the projector is restarted after...

3. Installation Guidelines
Image 3-15
Lamp adjustment access
3. Start up the adjustment mode and selectService.
ADJUSTMENT MODE
Select a path from below :
RANDOM ACCESS
INSTALLATION
SERVICE
Select with↑or↓
then 
 to return
Menu 3-2
4. Select Lamp. The Z-axis value indication (lamp menu in service mode) will be helpful while turning screw B .
SERVICE
IDENTIFICATION
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJ. ADDRESS
SERIAL COMMUNICATION
NETWORK
LAMP
DIMMING
MORE...
Select with↑or↓
then 
 to return
Menu...

3. Installation Guidelines
A
Image 3-16
Lamp Z-Axis alignment (Former lamp house)
B
A
Image 3-17
Lamp Z-Axis alignment (Universal lamp house)
6. Slowly turn the screw B (image 3-16, , image 3-17, using an Allenkeyof3mm,alittleclockwiseuntilthemaximumvalueofthe
Z-AXIS indication in the lamp menu is reached.
7. Tighten the lock nut on the adjustable screw to secure its position (nutdriver 10).
CAUTION:Never turn the other screws ! These are factory aligned.
22R5976654 SLM R12+ 27/01/2005 

3. Installation Guidelines
3.7 Lenses
Overview
• Lenses
• Lens selection
• Lens formulas
• Lens Installation
• Cleaning the lens
3.7.1 Lenses
Available lenses
TLD(1.6–2.0:1)R9840670
TLD(2.0–2.8:1)R9840680
TLD(2.8–5.0:1)R9840690
TLD(1.2:1)R9840770
TLD(0.8:1)R9840900
TLD(5.0–8.0:1)R9840910
TLD HB(0.8:1)R9842040
TLD HB(1.6–2.0:1)R9842060
TLD HB(2.0–2.8:1)R9842080
TLD HB(2.8–5.0:1)R9842100
TLD HB(5.0–8.0:1)R9842120
3.7.2 Lens selection
How to select ?
1. Determine the required screen width.
2. Determine the...

3. Installation Guidelines
Formulas for TLD lenses
Metric formulas (meter)Inch formulas (inch)
TLD(0.8:1)PD=0.77xSW+0.05PD=0.77SW+1.97
TLD(1.2:1)PD=1.11xSW-0.01PD=1.11xSW-0.39
TLD(1.6–2.0:1)PDmin=1.47xSW-0.09
PD
max=1.85xSW-0.13
PDmin=1.47xSW-3.54
PD
max=1.85xSW-5.12
TLD(2.0–2.8:1)PDmin=1.85xSW-0.17
PD
max=2.62xSW-0.24
PDmin=1.85xSW-6.69
PD
max=2.62xSW-9.45
TLD(2.8–5.0:1)PDmin=2.58xSW-0.16
PD
max=4.71xSW-0.38
PDmin=2.58xSW-6.30
PD
max=4.71xSW-14.96
TLD(5.0–8.0:1)PDmin=4.52xSW-0.01
PD
max=7.53xSW-0.29...

3. Installation Guidelines
Image 3-19
Mounted Lens
Caution:On a table mounted projector, hold the projector when pushing the lens into the lens blockto avoid sliding off from
the table.
3.7.5 Cleaning the lens
To minimize the possibility of damaging the optical coating or scratching exposed lens surface, we have de-
veloped recommendations for cleaning the lens. FIRST, we recommend you try to remove any material from
the lens by blowing it off with clean, dry deionized air. DO NOT use any liquid to clean...

3. Installation Guidelines
1 2
A
B
Image 3-20
Battery cover removal
2. Plug in the battery (9 V battery - type E-block or equivalent) onto the battery contact plate (A).
A
B
Image 3-21
Battery connection
3. Place the battery into the lower compartment (B) (image 3-21).
4. Insert the pins of the battery cover (A) into the slots on the bottom of battery back cover and close the cover by pushing downwards
(B) until it clicks.
AB
Image 3-22
Battery cover mount
5. A card, containing a button preset overview,...