Barco Hdx Series Installation Manual

							3. Physical installation
3.1.1 RCU battery installation
Where tofind the batteries for the remote control ?
The batteries are not placed in the remote control unit to avoid control operation in its package, resulting in a shorter battery life
time. At delivery the batteries can be found in a separated bag attached to the remote control unit. Before using your remote control,
install the batteriesfirst.
How to install the batteries in the remote control ?
1. Push the battery cover tab with thefingernail a little backwards (1) and pull, at the same time, the cover upwards (2).
12
Image 3-2
2. Insert the two AA size batteries, making sure the polarities match the + and - marks inside the battery compartment.
+ +-
-
Image 3-3
3. Insert (1) the lower tab of the battery cover in the gap at the bottom of the remote control, and press (2) the cover until it clicks
in place.
+ +-
-
1
2
Image 3-4
To prevent battery explosion
• Danger of explosion if battery is incorrectly installed.
• Replace only with the same or equivalent type recommended by the manufacturer.
• Disposal of used batteries must be done according to the manufacturer’s instruction.
R5905032 HDX SERIES 23/11/2011
27 
						

							3. Physical installation
3.1.2 RCU rugged case installation
How to install the rugged case of the remote control ?
1. Slide the bottom of the RCU into the rugged case and then pull the top of the rugged case over the top of the RCU as illustrated.
Image 3-5
28R5905032 HDX SERIES 23/11/2011 
						

							3. Physical installation
3.1.3 RCU XLR adaptor installation
Install the rugged case before installing the XLR adaptor. Vice-versa, remove the XLR adaptor before removing
the rugged case from the RCU.
Necessary tools
5mmflat screw driver.
How to install the XLR adaptor of the remote control unit ?
1. Push the XLR adaptor (C) upon the rugged case of the remote control unit as illustrated.
Note:Ensure that the text of the XLR adaptor is on top.
S C
S
Image 3-6
2. Fasten the two screws (S) of the XLR adaptor. Turn each screw repeatedly one or two turns until both screws are tight.
R5905032 HDX SERIES 23/11/2011
29 
						

							3. Physical installation
3.1.4 Using the XLR adaptor of the RCU
How to use the XLR adaptor of the remote control unit ?
1. Connect a cable with XLR plug into the XLR adaptor.
2. Connect the other end of the cable with your HDX projector.
3. Push the XLR adaptor completely against the rugged case of the remote control unit, as illustrated in the left image below, for
wired communication. Pull out the XLR adaptor (about 8 mm) to switch over to wireless communication.
Image 3-7
30R5905032 HDX SERIES 23/11/2011 
						

							3. Physical installation
3.1.5 RCU usage possibilities
Summarized possibilities
Ref.Possibility description
Comment
a.
RCU not wired
b.
RCU wired (mini-jack) Backlight illuminates continuously when wire is connected. Infra red
disabled.
c.
RCU with rugged case not wired
d.RCU with rugged case wired (mini-jack) Backlight illuminates continuously when wire is connected. Infra red
disabled.
e.
RCU with rugged case and XLR adaptor
pulled out “REMOTE” and not wiredThe XLR adaptor must be in the pulled out position “REMOTE”, otherwise
the RCU will not function.
f.RCU with rugged case and XLR adaptor
pulled out “REMOTE” and wiredThe RCU will send the commands via infra red to the projector.
g.
RCU with rugged case and XLR adaptor
pushed in “WIRED” and wiredThe RCU will send the commands via the cable connected with the XLR
adaptor to the projector. Backlight illuminates continuously when wire
is connected. Infra red disabled.
abcdfge
Image 3-8
R5905032 HDX SERIES 23/11/201131 
						

							3. Physical installation
3.2 Lenses
Overview
• Available lenses
• Lens selection
• Lens installation
• Lens removal
• Lens shift, zoom & focus
• Scheimpflug adjustment
32
R5905032 HDX SERIES 23/11/2011 
						

							3. Physical installation
3.2.1 Available lenses
Available lenses for the HDX projector projector
The TLD HB (High Brightness) lens series can be used on the HDX projector projector.
Image 3-9
R9852000:TLDHBfixedlens(0.8:1)Image 3-10
R9840770:TLDfixedlens(1.2: 1)Image 3-11
R9840775: TLD+ (1.2 : 1)fixed lens
Image 3-12
R9852010: TLD HB zoom lens (1.6 - 2.0 : 1)Image 3-13
R9842080: TLD HB zoom lens (2.0 - 2.8 : 1)Image 3-14
R9862030: TLD HB zoom lens (2.8 - 4,5 : 1)
Image 3-15
R9842120: TLD HB zoom lens (5.0 - 8.0 : 1)Image 3-16
R9862000: TLD+ lens (0.73 : 1)Image 3-17
R9862005: TLD+ zoom lens (1.16 - 1.49 : 1)
R5905032 HDX SERIES 23/11/201133 
						

							3. Physical installation
Image 3-18
R9862010: TLD+ zoom lens (1.5 - 2.0 : 1)Image 3-19
R9862020: TLD+ zoom lens (2.0 - 2.8 : 1)Image 3-20
R9862030: TLD+ zoom lens (2.8 - 4.5 : 1)
Image 3-21
R9862040: TLD+ zoom lens (4.5 - 7.5 : 1)Image 3-22
R9829997: TLD+ zoom lens (7.5 - 11.0 : 1)
34R5905032 HDX SERIES 23/11/2011 
						

							3. Physical installation
3.2.2 Lens selection
How to select the right lens
1. Determine the required screen width (SW).
2. Determine the approximate position of the projector in the room.
3. Start up theLens CalculatorontheBarcowebside:h
ttp://www.barco.com/en/tools/lenscalculatorto determine the possible
lenses for your configuration.
The Lens Calculator window opens.
Image 3-23
Lens calculator
The Lens Calculator can also be used to determine the position of the projector when the lens type and screen
width is known.
R5905032 HDX SERIES 23/11/201135 
						

							3. Physical installation
3.2.3 Lens installation
How to install
1. Remove the foam rubber in the opening of the lens holder if not removed yet.
2. Take the lens assembly out of its packing material and remove the lens caps on both sides.
3. Place the lens holder in the “unlocked” position by moving the lens lock handle (A) towards the lens power supply socket (B) as
illustrated.
A
B
Image 3-24
Lens installation, preparation
4. Ensure that the lens holder stands in the On-Axis position (horizontal and vertical mid position).
Note:The lens holder is placed default in the On-Axis position at factory.
5. Gently insert the lens in such a way that the lens connector matches the socket (B).
Image 3-25
Lens insertion
6. Insert the lens until the connector seats into the socket.
Warning:Do not release the Lens yet, as the Lens may fall out of the Lens Holder.
7. Secure the lens in the lens holder by sliding the lens lock handle into the “locked” position, which is away from the lens power
supply socket. Ensure the lens touches the front plate of the lens holder.
36
R5905032 HDX SERIES 23/11/2011