Barco Hdx Series Installation Manual

							D. DMX chart
D. DMX CHART
Overview
• DMX chart, Basic
• DMX chart, Full
• DMX chart, Extended
R5905032 HDX SERIES 23/11/2011
337 
						

							D. DMX chart
D.1 DMX chart, Basic
Overview
Chan-
nelFunction Value
DefaultAction
0 - 5 Mechanical shutter closed1 Intensity
6 - 255255
Electronic contrast on output
2 Function select 0 - 7
No function
8-15
Activate layout 1 (Main full screen) (If held for 2 seconds)
16 - 23
Activate layout 2 (PiP top right) (If held for 2 seconds)
24 - 31
Activate layout 3 (Split top bottom) (If held for 2 seconds)
32 - 39
Activate layout 4 (Split left right) (If held for 2 seconds)
40 - 47
Activate layout 5 (If held for 2 seconds)
48 - 55
Activate layout 6 (If held for 2 seconds)
56 - 63
Activate layout 7 (If held for 2 seconds)
64 - 71
Activate layout 8 (If held for 2 seconds)
72 - 79
Activate layout 9 (If held for 2 seconds)
80 - 87
Activate layout 10 (If held for 2 seconds)
88 - 95
Input 1 (If held for 2 seconds)
96 - 103
Input 2 (If held for 2 seconds)
104 - 111
Input 3 (If held for 2 seconds)
11 2 - 11 9
Input 4 (If held for 2 seconds)
120 - 207
No function
208 - 215
Power On / Lamp On (If held for 5 seconds)
216 - 223
Stand by / lamp Off (If held for 5 seconds)
224 - 231
XLR output voltage On (if held for 5 seconds)
232 - 239
XLR output voltage Off (if held for 5 seconds)
240 - 2550
No function
338R5905032 HDX SERIES 23/11/2011 
						

							D. DMX chart
D.2 DMX chart, Full
Overview
Chan-
nelFunction Value
DefaultAction
0 - 5 Mechanical shutter closed1 Intensity
6 - 255255
Electronic contrast on output
2 Brightness 0 - 255 128
Adjusts the brightness between 0 and 100% on input
3
Contrast0 - 255 128
Adjust the contrast between 0 and 100% on input
0-87
No function
88 - 95
Input 1 (if held for 2 seconds)
96 - 103
Input 2 (if held for 2 seconds)
104 - 111
Input 3 (if held for 2 seconds)
11 2 - 11 9
Input 4 (if held for 2 seconds)
4 Input selection
120 - 2550
No function
0-31
No function
32 - 63 Focus motor
64 - 95 Zoom motor
96 - 127
Lens shift Right Left
128 - 159
Lens shift Up Down
160 - 191
Power On / Lamp On (together with channel 6 and 7 held in 255
for 5 sec)
192 - 223
Stand By / Lamp Off (together with channel 6 and 7 held in 255
for 5 sec)
5
Function select
224 - 2550
Return lens to center position (if held for 5 seconds)
0-31
Stop
32 - 63 Run
64 - 223
No function
6
Motor Go >>
224 - 2550
Move lens to maximum position
0-31
Stop
32 - 63 Run
64 - 223
No function
7
Motor Go 
						

							D. DMX chart
D.3 DMX chart, Extended
Overview
Chan-
nelFunction Value
DefaultActions
0 - 5 Mechanical shutter closed1 Intensity
6-255255
Electronic contrast on output
2 Brightness 0 - 255 128
Adjusts the brightness between 0 and 100% on input
3
Contrast0 - 255 128
Adjusts the contrast between 0 and 100% on input
0-87
No function
88 - 95
Input 1 (if held for 2 seconds)
96 - 103
Input 2 (if held for 2 seconds)
104 - 111
Input 3 (if held for 2 seconds)
11 2 - 11 9
Input 4 (if held for 2 seconds)
4 Input selection
120 - 2550
No function
0-7
No function
8-15
Lens shift Right
16 - 23
No function
24 - 31
Lens shift Left
32 - 39
No function
40 - 47
Lens shift up
48 - 55
No function
56 - 63
Lens shift down
64 - 231
No function
232 - 239
Return lens to center (if held for 5 seconds)
240 - 247
Calibrate lens zoom + focus (if held for 5 seconds)
5 Lens control
248 - 2550
No function
6
Focus (MSB)0 - 255 128
Coarse lens focus adjustment9
7
Focus (LSB)0 - 255 128
Fine lens focus adjustment9
8
Zoom (MSB)0 - 255 128
Coarse lens zoom adjustment9
9
Zoom (LSB)0 - 255 128 Fine lens zoom adjustment9
0-7
Lamp power 100%
8-15
Lamp power 95%
16 - 23
Lamp power 90%
24 - 31
Lamp power 85%
32 - 39
Lamp power 80%
40 - 47
Lamp power 75%
48 - 55
Lamp power 70%
56 - 63
Lamp power 65%
64 - 71
Lamp power 60%
72 - 79
Lamp power 55%
80 - 207
No function
208 - 215
Power On / Lamp On (If held for 5 seconds)
216 - 223
Stand by / Lamp Off (if held for 5 seconds)
224 - 231
XLR output voltage On (if held for 5 seconds)
232 - 239
XLR output voltage Off (if held for 5 seconds)
10
Lamp Control
240 - 2550
No function
9. Only when lens is calibrated
340R5905032 HDX SERIES 23/11/2011 
						

							E. Stacking HDX projectors
E. STACKING HDX PROJECTORS
Overview
• Mount stacking points
• Stacking HDX projectors
• Aligning stacked HDX projectors
R5905032 HDX SERIES 23/11/2011
341 
						

							E. Stacking HDX projectors
E.1 Mount stacking points
Necessary tools
Allenkey8mm
How to mount
1. Place thefirst stacking point on a corner.
Image E-1
Stacking points, mount
2. Turn in the delivered bolt.
3. Repeat for the other 3 stacking points.
342
R5905032 HDX SERIES 23/11/2011 
						

							E. Stacking HDX projectors
E.2 Stacking HDX projectors
CAUTION:Maximum stack three (3) projectors in a table mounted configuration.
Maximum stack two (2) projectors in a ceiling mounted configuration.
How to stack
1. Mount stacking points on lower projector. See Mount stacking points, page 342.
2. Mount a bottom carry handle on the upper projector. See Mounting the bottom carry handler, page 46.
3. Place the projector with carry handle on top of the projector with stacking points.
Make sue that all interlocking pins match with their corresponding interlocking sockets.
Image E-2
Dual stack
Tip:In case of stacking projectors for a ceiling mount configuration,first turn the projectors upside down before placing the
projectors on top of each other.
4. Attach the two projectors together by closing all four interlocking adapters.
ABCD
Image E-3
Interlocking, close
R5905032 HDX SERIES 23/11/2011343 
						

							E. Stacking HDX projectors
Extra actions for ceiling mounted stack
Two safety cables must be mounted between both projectors.
1. Mount the safety cable around the carrying handle of the bottom projector. Push the safety hook through the loop.
Image E-4
Security cables, mount
2. Mount the other end of the security cable around the carry handle of the top projector and clasp the safety hook round the cable
as illustrated.
Make sure that the falling distance is maximum 20 cm. If necessary, before clasping the safety hook around the cable, turn the
cable a few time around the carry handle.
3. Repeat this procedure for the second safety cable on the other side of the carry handle.
WARNING:Always use both safety cables of the lowest projector to secure a stacked projector in a ceiling
mount configuration.
How to open an interlocking adapter
1. Open an interlocking adaptor as illustrated.
344
R5905032 HDX SERIES 23/11/2011 
						

							E. Stacking HDX projectors
D
CBA
Image E-5
Interlocking, open
WARNING:Never open an interlocking adapter of a stacked projector which is still suspended. First place
the stacked projectors on thefloor.
R5905032 HDX SERIES 23/11/2011345 
						

							E. Stacking HDX projectors
E.3 Aligning stacked HDX projectors
Necessary tools
No tools.
How to align stacked projectors
1. Make sure that the internal hatch pattern projected by the reference projector is sharp and has a perfect rectangle outline. If this
is not the case, readjust the reference projector before aligning the other stacked projector(s) with the reference hatch pattern.
Note:The reference projector in a stacked configuration is the lowest projector in case of table mount and the uppermost
projector in case of ceiling mount.
2. Project with the stacked projector the same internal hatch pattern as the reference projector.
Tip:Use a white colored hatch pattern for the reference projector and e.g. green colored for the stacked projector. This
makes it easier to see the difference between both hatch patterns projected.
3. If necessary, adjust the rotation of the stacked projector with respect to the reference projector by turning in or out the height
adjustment ring of the interlocking adaptors at the rear of the stacked projector. Adjust until the outline of the hatch pattern is
most symmetric with the reference hatch pattern.
Rotation
Image E-6
Stacked projectors, rotation
4. If necessary, adjust the inclination of the stacked projector with respect to the reference projector by turning the height adjustment
ring of the interlocking adaptor at the front of the stacked projector in or out. Adjust until the outline of the hatch pattern is most
symmetric with the reference hatch pattern.
Inclination
Image E-7
Stacked projectors, inclination
346R5905032 HDX SERIES 23/11/2011