Barco Hdx Series Installation Manual

							9. Image
9.5.2 Advanced timings, clamp delay - clamp width
About the advanced settings
Clamp delay The time between the trailing edge of the sync pulse and the leading edge of the clamp pulse, in pixels.
Can be any value between 0 and 255.
Clamp width The width of the clamp pulse can be any value between 0 and 255.
Sync
pulse
Clamp
pulse
Clamp
delayClamp
width
Leading edge
Trailinging edge
Image 9-50
How to change the clamp delay - clamp width
1. PressMenuto activate the menus and selectImage→Timings→Advanced settings.
Image 9-51
Main menu, Image
Image 9-52
Image, timings
Image 9-53
Timings, advanced settings
2. PressENTERto select.
R5905032 HDX SERIES 23/11/2011
137 
						

							9. Image
Image 9-54
Clamp delay
3. Use the▲or▼key to selectClamp DelayorClamp Widthand use the◄or►key to change the value.
Or,
pressENTERto open the specific adjustment menu. Follow the adjustment method as described in Navigation and adjust-
ments, page 89.
138
R5905032 HDX SERIES 23/11/2011 
						

							9. Image
9.6 Image File Services
R5905032 HDX SERIES 23/11/2011139 
						

							9. Image
9.6.1 Files andfile manipulations
Connecting a new source.
Source dependent adjustments like image settings, aspect ratio and timings are stored in a dedicated imagefile.
Before using a new source, a correct imagefile has to be installed. The projector’s memory contains a list offiles corresponding to
the most used sources. When the new source corresponds with one of thesefiles, thefile can be loaded and saved for future use.
When there is a little difference, thefile can also be loaded and then edited until the source specs are reached.
VESA standards and video standards are pre-programmed.
Possiblefile Manipulations
The followingfile manipulations are possible :
• Load : load the settings of a selectedfile for the current selected source of the active window (main or PiP)
• Rename : renaming afile.
• Delete : deleting afile (only customfiles)
• Delete all : delete all customfiles
• Options : way of loading afile when a source is selected.
140
R5905032 HDX SERIES 23/11/2011 
						

							9. Image
9.6.2 Manual Loadfile
How to load
1. PressMenuto activate the menus and selectImage→Image File Services→Manual Load.
Image 9-55
Main menu, Image
Image 9-56
Image, imagefile services
Image 9-57
Imagefile services
2. PressENTERto select.
Depending on theFile Load Filtersetting a full list or a listfitting the selected source is displayed.
When staying for at least 3 seconds on the samefile selection after scrolling through the list of imagefiles a pre-load is started.
Image 9-58
Loadfile
3. Use the▲or▼key to select the desiredfile and pressENTERto load thisfile.
The image is not perfect
If the displayed image is not correct after selecting the bestfittingfile,gototheTimingsmenu and change thefile settings.
R5905032 HDX SERIES 23/11/2011
141 
						

							9. Image
9.6.3 File Load Filter
About thefilter setting
Depending on the loadfilefilter, the load list can be reduced to thefittedfiles or can be expanded to show allfiles.
[Fit] : reduced list corresponding with the input source.
[All] : full list with all availablefiles in the projector.
How to set up
1. PressMenuto activate the menus and selectImage→Image File Services→File Load Filter.
Image 9-59
Main menu, Image
Image 9-60
Image, imagefile services
Image 9-61
File loadfilter
2. PressENTERto toggle between[All]and[Fit].
142
R5905032 HDX SERIES 23/11/2011 
						

							9. Image
9.6.4 Delete afile
What can be done ?
A custom imagefile can be deleted. Be aware that an activefile can’t be deleted.
How to delete
1. PressMenuto activate the menus and selectImage→Image File Services→Delete.
Image 9-62
Main menu, Image
Image 9-63
Image, imagefile services
Image 9-64
Imagefile services, delete
2. PressENTERto select.
The available customfiles are displayed.
If no customfiles are available, a message that no customfiles are available is displayed.
3. Use the▲or▼key to select thefile to delete.
Image 9-65
Delete customfile
4. PressENTERto delete the selectedfile.
No recovery possible !
R5905032 HDX SERIES 23/11/2011143 
						

							9. Image
9.6.5 Delete all customfiles
What can be done ?
All custom imagefiles can be deleted by executing a single command. Be aware that an activefile can’t be deleted.
Imagefiles of active sources on input 1 to 4 cannot be deleted.
How to delete
1. PressMenuto activate the menus and selectImage→Image File Services→Delete.
Image 9-66
Main menu, Image
Image 9-67
Image, imagefile services
Image 9-68
Delete all customfiles
If no customfiles are available, a message that no customfiles are available is displayed.
2. Use the▲or▼key to selectYe sorNo.
Image 9-69
Delete all
3. IfYe sis selected, pressENTERto delete all customfiles.
IfNois selected, pressENTERto return to theImage File Servicesmenu without deleting any customfile.
No recovery possible !
144R5905032 HDX SERIES 23/11/2011 
						

							9. Image
9.6.6 Rename customfiles
A rename operation is only applicable for custom imagefiles.
How to rename
1. PressMenuto activate the menus and selectImage→Image File Services→Rename.
Image 9-70
Main menu, Image
Image 9-71
Image, imagefile services
Image 9-72
Imagefile services, rename
2. PressENTERto select.
The available customfiles are displayed.
If no customfiles are available, a message that no customfiles are available is displayed.
Image 9-73
Rename, list offiles
3. Use the▲or▼key to select thefile to rename and pressENTER.
R5905032 HDX SERIES 23/11/2011
145 
						

							9. Image
The rename window opens.
Image 9-74
Renamefile
4. Use the▲or▼key to change the selected character.
Use the◄or►key to select another character.
Note:Digits can be entered with the digit keys on the remote control or the local keypad. When a digit is enteredinthatway,
the next character will be selected automatically. Arrow key left (◄) has the backspace functionality.
5. PressENTERtofinalize the rename action.
146
R5905032 HDX SERIES 23/11/2011