Aimco Brakes Freedom3 SPC Sqnet User Manual

 
 
   [email protected]     
51  
 
 
Yield +Angle 
 
 
 
 
Selecting this strategy in “General data” tab of “Freedom wrenches Tightening program 
definition”, Freedom³ will detect automatically the yield point, after detection, user has to 
continue to tighten reaching a specific angle ( Nominal Angle).In case the Yiled point is not 
recognized, Freedom³ will display an error message.  The Angle value is counted starting from 
Yield point. The result will be considered “OK” if the angle and torque...

52 
 
 
 
 
 
 
- Click on “Tool” Tab 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  

 
 
   [email protected]     
53  
 
 
 
Fields And Meaning Table for “Freedom wrenches tightening program definition” Tool Tab: 
 
 
Fields Meaning 
Tool Nr. =t’s the identification number of the tool (end 
fitting) 
Torque Correction Factor =t’s a torque factor. User must fill this field only 
if on the wrench is plugged an extension that 
modifies the original calibration length. See 
figure below to calculate the factor< 
Angle Correction Factor =t’s an angle factor. User must fill tUis field...

54 
 
 
 
 
 
 
- Click on Leds Tab 
 
 
 
 
 
 
Note: 
In this page is possible to customize the percentage to light every single led on the wrench 
considering the target.   
 
 
 
 
  

 
 
   [email protected]     
55  
 
 
 
- Click on Batch Tab  
 
 
 
 
 
 
Note: 
Inside Batch Tab is possible to multiply the number of screws to tighten. For example, usually to 
mount a wheel on the car there are 4 or 5 screws to tighten with the same strategy for all screws. 
=n this Tab is possible to define how many screws “Freedom³ has to tighten”. 
 
 
 
 
  

56 
 
 
 
 
 
 
See  table below  to fill correctly all fields. 
 
Fields Meaning 
Screws nr In this field, user has to indicate the number of 
screws to tighten with Freedom³ (for example if 
there are 3 screws, SQ-net will send to 
Freedom³ 3 time the same tightening program) 
Enable batch Click on check box in order to enable Batch 
function 
Strategy In this field is possible to define the strategy in 
order to drive the wrench considering the 
status of the tightening: 
Count only ok results->...

 
 
   [email protected]     
57  
How to create a route 
 
 
A route is a group of Control Quality test or tightening strategy. Freedom³ can receive Control 
Quality  route, Tightening Program route or both. To send tests or tightening programs from SQ-
Net to Freedom³, user must create a route in SQ-Net and send it. 
From SQ-Net front page, select route management icon: 
 
Route Management Icon 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  

58 
 
 
 
 
A new window will appear: 
 
 
 
 
 
 
 
 
 
 
  

 
 
   [email protected]     
59  
 
 
 
In route management window is possible : 
 
ICON FUNCTIONS 
 
Select an existing route in order to add or remove test 
 
Edit a new route 
 
Modify a route 
 
Delete a route 
 
Add and remove test from route 
 
Select test from route 
 
 
 
    
Click on new route to create a new one 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  

60 
 
 
 
 
=t will appear a new window “Add a new route”: 
            
 
             
             
      
 
 
 
Here, user must select the right type of route: 
Quality Control: if in the route there are only Quality Control Test 
Freedom wrenches programs: if in the route there are only tightening programs 
Mix: if in the route there are Quality Control Test and Tightening   programs