Home > Aimco Brakes > Torque Measurement > Aimco Brakes Freedom3 SPC Sqnet User Manual

Aimco Brakes Freedom3 SPC Sqnet User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Aimco Brakes Freedom3 SPC Sqnet User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 85 Aimco Brakes manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							 
     
       [email protected]     
    51  
     
     
    Yield +Angle 
     
     
     
     
    Selecting this strategy in “General data” tab of “Freedom wrenches Tightening program 
    definition”, Freedom³ will detect automatically the yield point, after detection, user has to 
    continue to tighten reaching a specific angle ( Nominal Angle).In case the Yiled point is not 
    recognized, Freedom³ will display an error message.  The Angle value is counted starting from 
    Yield point. The result will be considered “OK” if the angle and torque values will be in the 
    tolerances (inside the green window). In this tightening strategy both parameters torque and 
    angle values will be considered for statistic charts (wrench collects all time angle and torque 
    values). 
     
    Note  
    This tightening strategy is available only for Fredoom³ SPC mode. 
     
     
     
     
     
     
     
     
      
    						
    							 
     
       [email protected]     
    53  
     
     
     
    Fields And Meaning Table for “Freedom wrenches tightening program definition” Tool Tab: 
     
     
    Fields Meaning 
    Tool Nr. =t’s the identification number of the tool (end 
    fitting) 
    Torque Correction Factor =t’s a torque factor. User must fill this field only 
    if on the wrench is plugged an extension that 
    modifies the original calibration length. See 
    figure below to calculate the factor< 
    Angle Correction Factor =t’s an angle factor. User must fill tUis field  
    Flexion Correction Factor =t’s the  angular error  due to the extension 
    tool. user must measure it using a protractor or 
    a rotary transducer mounted at the end of the 
    extension (close to the joint) and see the 
    different between the angle reading of the 
    wrench and the angle  reading of the protractor 
    or the rotary transducer. Example if the 
    different is 3
    						
    							54 
     
     
     
     
     
     
    - Click on Leds Tab 
     
     
     
     
     
     
    Note: 
    In this page is possible to customize the percentage to light every single led on the wrench 
    considering the target.   
     
     
     
     
      
    						
    							 
     
       [email protected]     
    55  
     
     
     
    - Click on Batch Tab  
     
     
     
     
     
     
    Note: 
    Inside Batch Tab is possible to multiply the number of screws to tighten. For example, usually to 
    mount a wheel on the car there are 4 or 5 screws to tighten with the same strategy for all screws. 
    =n this Tab is possible to define how many screws “Freedom³ has to tighten”. 
     
     
     
     
      
    						
    							56 
     
     
     
     
     
     
    See  table below  to fill correctly all fields. 
     
    Fields Meaning 
    Screws nr In this field, user has to indicate the number of 
    screws to tighten with Freedom³ (for example if 
    there are 3 screws, SQ-net will send to 
    Freedom³ 3 time the same tightening program) 
    Enable batch Click on check box in order to enable Batch 
    function 
    Strategy In this field is possible to define the strategy in 
    order to drive the wrench considering the 
    status of the tightening: 
    Count only ok results-> selecting this option the 
    wrench will consider the batch completed only 
    if Freedom³ will get the number of batch all ok 
    (for example if there are 3 screws to tighten, 
    the batch will be completed only after getting 3 
    ok results), All not ok results are not 
    considerate for batch counting. 
    In case of error redo the batch-> selecting this 
    option all time operator get a not ok result, he 
    must restart from the complete batch from the 
    first screw, that means if there are 3 screws to 
    tighten, if the user get a not ok result on last 
    screw, he must restart the complete batch 
    from the first screw (all the other results are 
    not considerate). 
    In case of error redo last operation->  selecting 
    this option all time operator get a not ok result, 
    he must retightening only the last screw. 
     
     
     
     
     
     
     
     
     
     
      
    						
    							 
     
       [email protected]     
    57  
    How to create a route 
     
     
    A route is a group of Control Quality test or tightening strategy. Freedom³ can receive Control 
    Quality  route, Tightening Program route or both. To send tests or tightening programs from SQ-
    Net to Freedom³, user must create a route in SQ-Net and send it. 
    From SQ-Net front page, select route management icon: 
     
    Route Management Icon 
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
      
    						
    							 
     
       [email protected]     
    59  
     
     
     
    In route management window is possible : 
     
    ICON FUNCTIONS 
     
    Select an existing route in order to add or remove test 
     
    Edit a new route 
     
    Modify a route 
     
    Delete a route 
     
    Add and remove test from route 
     
    Select test from route 
     
     
     
        
    Click on new route to create a new one 
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
      
    						
    							60 
     
     
     
     
    =t will appear a new window “Add a new route”: 
                
     
                 
                 
          
     
     
     
    Here, user must select the right type of route: 
    Quality Control: if in the route there are only Quality Control Test 
    Freedom wrenches programs: if in the route there are only tightening programs 
    Mix: if in the route there are Quality Control Test and Tightening   programs 
     
     
     
     
     
     
     
     
     
     
     
     
     
      
    						
    All Aimco Brakes manuals Comments (0)

    Related Manuals for Aimco Brakes Freedom3 SPC Sqnet User Manual