Aimco Brakes Freedom3 SPC Sqnet User Manual
Have a look at the manual Aimco Brakes Freedom3 SPC Sqnet User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 85 Aimco Brakes manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
[email protected] 101 Freedom³ SPC Setup Menu Freedom³ allows to customize many settings. See below for enter in the setup and to modify every single setting. From main menu of Freedom³ select “Setup” icon: Then Freedom³ will ask to enter the password to get in. Type the password “1247”. It will appear a new window, select setup:
102 So, it will appear the setup menu window: On the Top of the window is showed the title of the setting, on the bottom the possible selections. To make selection in the menu it’s enough touch the screen. Please see table below for the mining of every single argument (setting): Arguments (settings) Definition Language This setting allows to choose the language: it’s possible to select one of the following languages: English - Italian – German – French – Portuguese – Spanish – Hungarian (special version). Auto Off Time (min) 0=manual This setting allow to switch off Freedom ³ automatically, in order to save battery when the wrench is not used. The value is in minutes. Test Result freeze time This setting indicates how long the result will be displayed at the end of every single test. Default value 2000 ms. No. of XR samples It’s the minimum number of samples to create an average value for X/R charts. No. of Cp samples =t’s the number of samples for Cm/cp test. For SPC Freedom
[email protected] 103 Light Intens. This setting allows user to adjust the brightness. Light Timeout Freedom³ has two light screen modalities, when it’s not used for a specific time (light time out) FREEDOM³ goes in energy saving modality in order to save battery. Last Led% This function allows the operator to light the last led when he wants in order to stop in time without over-tighten the bolt. For example operator can set it at 95% of target in order to stop in time. Date/Time This setting allows to adjust Date and Time. Automatic Test Repetition When it’s enabled, in SPC version, After user has completed a test, FREEDOM³ restarts automatically the same test. SPC Control Type It’s a different way to evaluate test, there are 2 options, “Control on nominal tolerance” is the normal selection, the results of test depend from the position of the samples considering Upper and lower control limits (ISO 8258); “Control on Predefined Limits” is a special control for a specific customized application. List Front Size It’s the size of character, there are only 2 options “Small” and “Big” Force Peak Res Enabling this function, Freedom³ will consider as result the maximum torque(or angle) reached during test. In this case,FREEDOM³ will not consider the first peak. Smart Brk/Angle Enabling this function when user run breakaway angle test, FREEDOM³ will recognize automatically Breakaway point.
104 Freedom³ PRW Setup Menu Freedom³ can be set in different way, for every single modality is necessary to set the wrench in a specific way. See below to know how to enter in the setup and to set the wrench to work by Bluetooth via “dll”. From main manu, select “setup” icon: A new window will appear: Select again the “Setup” icon and type the password “1247” It will be appear the “Setup” window:
[email protected] 105 In the table below are explained all setup items. The item in yellow are for PRW with Bluetooth via “dll” version. Setup Item Meaning Set version This item allows to select if the wrench must work with a special or default version. Language This item allows to choose one of the following languages: English; Italian; German; French; Portuguese; Spanish. Server/Client mode This item allows to configure if the wrench must be Client or Server in the paring with Bluetooth. Must work on line This item, if enabled, let work the wrench only if is connected to a net or (Bluetooth) RS232 Baudrate This item allows to select parameters for RS232 communication. Wrench ID Wrench Identification Has Radio Enable this item only if there is a radio module installed on board. Radio Type This item allow to select which radio module is installed on the wrench. Baud 232 Radio This item allows to select the serial parameters for communication with radio.
106 Setup Item Meaning Net Id “Group” identifier for 868 MHY radio Node IT “Node” identifier for 868 M:z radio Master IT Only for SCS Radio Channel Only for SCS Radio Power Only for SCS Online PerioT Only for SCS Has Tool Recognition Enable this item only if the wrench has “socket tool recognition” installed on board. Tool selects Prog< Enable this item only if the “socket tool” selects the program. Password per Firmware If is enabled, the wrench will ask for a password to change firmware< Has Positioning Enable only if on the wrench is installed the positioning function< Send Long Res. This item allows to select if it’s standard o customized< Job restart strat. Yhis item allows to ask if, at the end of the job, the wrench must “restart” the same job or “continue” start with next program or “ask” to user if has to restart the same job or continue. NOO come OO With this item if enabled, after a “Not Ok Result” Freedom
[email protected] 107 Setup Item Meaning Light TimeOut Freedom³ has 2 different light levels, one is standby and the other one is for work modality. By this item is possible to set how long the wrench waits before to switch from work to standby modality when it’s not receiving any input. The time is in seconds. PowerOff sec.(0=never) If the wrench is not used can switch off automatically. Select “0” to disable. The time is in second. All Misure in Window If this item is enable, Freedom³ will use short time-out only when torque and angle are in the tolerance window. Set Tool Number Only for SCS Tool Tq Corr. Only for SCS Tool Ang Corr (°-Nm) Only for SCS Adapter Len. (mm) If user is using an extension to tighten, he must write the length of the extension (otherwise torque reading will be not correct). If user has already set a factor in the menu “Tool Tq Corr.” Freedom³ will consider only the value in “Tool Tq Corr”. Comm. Fail Strategy When Freedom³ is connected to VPG (or another software) by radio, in case line is dropped, it’s possible to define a specific strategy: “Warn and disable” Freedom³ displays the message “:ost not connected” and disables itself; “Allow disconnected mode” Freedom³ displays the message “:ost not connected” then operators can push for 4 seconds confirm button on keyboard to continue to work in off- line mode; “Complete Current job/batch” in this case Freedom³ allows operator to finish the current job or batch then Freedom³ will display the message “:ost not connected” and disable itself. AllowsSuspendSendRes Special version for IVECO. When the radio communication is off the wrench can work saving in its memory all results. When the communication is on Freedom³ will send all results to the Host.
108 Setup Item Meaning Led green at Nom. If enabled, the wrench will light the green led when torque or angle target are reached. Vibration Enable vibration when target is reached. Input Vin If enabled, user must read the Vin number after program selection; user must read the Vin before program selection; User must read the vin when the radio communication is off (special system for IVECO) BarCode Use Enable only if on the wrench is installed barcode reader Confirm Scanned String If enabled, After bar code reading, user must push confirm button on keyboard. BArCode Setup This item allows to setup the barcode reading directly form barcode configuration. Alw save curve Set “1” to save always the curves< End at last led If enabled, Short time;out will start considering the positioning of last led (it’s possible to set by SQnet or VPG when Freedom
[email protected] 109 Setup Item Meaning Conn. To Schatz Enable to connect Freedom³ with Schatz bench (bench for torque/angle calibration) Schatz baud Rs232 parameters for connection with Schatz bench. Fix Cable Port Only for SCS. Used for Freedom³ or EWW³ to select the port. Plug in Cable Port Only for Freedom³ first generation Cradle Input Only for Freedom³ with “R=D” sensor, to recognize when Freedom³ is positioned on cradle battery charger. Adapter Coeff. Mode This setting is used to define which input has the priority to define “adapter coefficient mode”, if enabled: “Adapter Prio” Freedom³ will consider, in case the coefficient is written in the tool/adapter and in the program sent from VPG or another host software, before that written in the toll/adapter; “Only Adapter” Freedom³ will consider only the coefficient written in the adapter (if it’s written); “program Prio”Freedom³ will consider, in case the coefficient is written in the tool/adapter and in the program sent from VPG or another host software, before that written in the program; “only Program” Freedom³ will consider only the coefficient written in the program (if it’s written). Speed Over Delay (ms) This time indicates how long the gyroscope can stay over the maximum speed, once over this time, Freedom³ will display the error message “speed over” (this happens when user tightens too fast). Freq. RT reading (Hz) In this setting is possible to choose the frequency for sending value to VPG in real time.
110 Part Numbers Part Numbers Model Description 113 16 0015 Freedom³ 15 Nm Torque-Angle Wrench 113 16 0030 Freedom³ 30 Nm Torque-Angle Wrench 113 16 0070 Freedom³ 70 Nm Torque-Angle Wrench 113 16 0100 Freedom³ 100 Nm Torque-Angle Wrench 113 16 0200 Freedom³ 200 Nm Torque-Angle Wrench 113 16 0300 Freedom³ 300 Nm Torque-Angle Wrench 113 16 0400 Freedom³ 400 Nm Torque-Angle Wrench 113 16 0600 Freedom³ 600 Nm Torque-Angle Wrench 113 16 0800 Freedom³ 800 Nm Torque-Angle Wrench 113 16 1000 Freedom³ 1000 Nm Torque-Angle Wrench 197 14 0005 Barcode Reader Int. Freedom³ accessory 197 14 0001 Bluetooth Integrated Module Freedom³ accessory 197 14 0003 868 MHz Integrated Module Freedom³ accessory 197 14 0002 WIFI Integrated Module Freedom³ accessory 19714 0011 Automatic Recognition of Inserted Socket Freedom³ accessory 313 11 0011 Rubber Protection Freedom³ accessory 313 11 0030 Rubber Protection with Display Protection Freedom³ accessory 313 21 0042 Additional Battery Freedom³ spare part 19714 0017 External battery charger Freedom³ accessory 197 14 0018 External Battery Charger for 2 batteries Freedom³ spare part 197 14 0012 Automatic Recognition of Unlimited Transducers Freedom³ accessory 197 14 0014 Predisposition for Cradle Freedom³ accessory 197 13 0003 Cradle Freedom³ accessory