Home > Aimco Brakes > Torque Measurement > Aimco Brakes Freedom3 SPC Sqnet User Manual

Aimco Brakes Freedom3 SPC Sqnet User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Aimco Brakes Freedom3 SPC Sqnet User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 85 Aimco Brakes manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							 
     
       [email protected]     
    81  
    How to run test from route - Freedom³ SPC - 
     
     
    From the main page of Freedom³ select the type of test to run “Process Capability” or “Cp/Cm”: 
     
     
     
     
     
     
     
    Selecting  Process Capability, it will appear on the display: 
     
     
       
     
    Freedom³ shows root and folders in the same way were created in SQ-net, but every single folder 
    corresponds a single page on Freedom³. 
     
    Press “right arrow” on Freedom³ keyboard to display next folder. 
     
      
    						
    							82 
     
     
    The second level folder will appear (like SQ-net): 
     
      
     
     
     
     
    Press again the “right arrow” on Freedom³ keyboard for third level folder: 
     
           
                          
     
     
     
     
     
     
     
     
     
     
     
     
     
     
      
    						
    							 
     
       [email protected]     
    83  
     
     
    Pressing again “right arrow” Freedom³ will display tests regarding the specific location: 
     
     
     
     
    Select the test by “Up” and “Down” arrows and press confirm on Freedom³ Keyboard. 
     
     
     
    A new window will appear: 
     
     
     
     
     
    TORQUE 
     
     
     
     
    ANGLE 
     
     
     
    The wrench is ready to tighten  
     
     
      
    						
    							84 
     
     
     
     
    At the end of tightening Freedom³ will show the 
    results:
     
    The results in green color are inside tolerances, in red colors are outside. At the end of the test,  
    Freedom³ will display the list of test related to the location with the status of last test: 
     
     
     
     
     
     
     
     
     
              
    Number of tests done and 
    grup size ( see paragrafh 
    SPC QualityControl Test 
    and SPC Production Tool 
    Test) 
    Message about status of 
    measure  
    						
    							 
     
       [email protected]     
    85  
    How to run test from route - Freedom³ PRW - 
     
     
    From main page of Freedom³ is possible to choose the type of test to run “Select Program” or 
    “Select Hob”. 
    Select Program -> If user wants select the operation to run one by one without following any 
    sequence 
    Select Job -> If user wants to follow a sequence of operation or only have a specific part of route 
    test (group) 
     
     
    Select Program 
    On main page of Freedom³ touch “Select Program”: 
     
     
     
     
     
     
    =f enabled, Freedom³ will ask for “=nput Vin 
    number” before to proceed. (See PRW 
    setup paragraph, to enable it): 
     
     
      
     
     
     
     
     
     
     
     
     
     
     
    Type the Vin Number and press “OK” than Freedom³ will open the “Select Program” page.  
    						
    							86 
     
     
     
     
    =n “Select Program” page is possible to select  from which operation user will start. 
     
     
     
     
     
     Operations 
     
     
     
     
     
     
     
     
     
     
     
    Once the program is select press confirm on Freedom³ keyboard, the wrench is ready: 
     
     
           Number of test to do 
     
     
    Operation name    
       Target and  
      tolerance  
        limits 
     
    Units of measurements 
     
        Progression  
        bar 
     
     
     
     
         Message for operator 
     
     
    Now operator can start to tighten up the target. 
     
     
     
      
    						
    							 
     
       [email protected]     
    87  
    If the torque and angle results will be in side tolerance limits, Freedom³ will display torque and 
    angle value with green color. Otherwise, if torque or angle are outside of tolerance limits, the out 
    value will be displayed with red color. In case torque and angle are out of tolerance limits, both 
    will be displayed with red color. 
     
    =n case of “Not OK” result Freedom³ will display a message “Confirm” pushing confirm button on 
    keyboard or “Discard” pushing left arrow on keyboard. 
     
     
     
     
    Select Job 
    One of the option available with Freedom³ is to wok using “Hob”. The work with Job, user must 
    send from SQnet a route with job\s (group\s) inside, see paragraph “how to create a route”. 
     
    From main page of Freedom³, touch “Select Hob” 
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
    =f enabled, Freedom³ will ask for “=nput Vin number” before to proceed. (See PRW setup 
    paragraph, to enable it) 
    Type the Vin Number and press “OK” then Freedom³ will open the “Select Hob” page:  
    						
    							88 
     
     
     
    =n the example above there is only one “Hob”, user can create more jobs in a route. 
     
    Once the “Hob” is selected press confirm on Freedom³ keyboard to start the job. 
    Depending from the sequence of every single operation (see paragraph, how create a route) 
    Freedom³ will start the job from first operation and the operator must follow the sequence 
    specified in the job. When all operation complete last “screw” of last operation Freedom³ will 
    display the message “Hob completed”. 
     
    During the tightening operation Freedom³ will show the test interface: 
     
     
     
     
      
      
    						
    							 
     
       [email protected]     
    89  
    When the Hob is finished, push on “ESC” keyboard button, to go back to main menu or select 
    another job. =t’s also possible repeat the same job, Freedom³will store all data-results in the 
    memory. For every test Freedom³ save data-results and curves (Torque/Time,Torque/angle). 
    See paragraph “Freedom³ PRW “:ow to send data-results to SQnet”” 
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
      
    						
    							90 
     
    Freedom³ SPC “How to send data results to SQ-Net” 
     
     
    STEP -1- 
    To send back data results  to SQ-Net user must connect Freedom³ to PC by USB 
    cable 
     
                 
                 
                 
            
            
            
           
            
            
            
      
     
     
     
    STEP -2- 
    Once USB cable is connected to computer and Freedom³, switch on Freedom³ and from the main 
    page select “Synchronize” icon. 
     
                 
                 
        
        
        
        
          
          
          
          
          
          
          
          
        
     
     
                  
    USB CABLE  
    						
    All Aimco Brakes manuals Comments (0)

    Related Manuals for Aimco Brakes Freedom3 SPC Sqnet User Manual