Home > Aimco Brakes > Torque Measurement > Aimco Brakes Freedom3 SPC Sqnet User Manual

Aimco Brakes Freedom3 SPC Sqnet User Manual

Here you can view all the pages of manual Aimco Brakes Freedom3 SPC Sqnet User Manual. The Aimco Brakes manuals for Torque Measurement are available online for free. You can easily download all the documents as PDF.

Page 81

 
 
   [email protected]     
81  
How to run test from route - Freedom³ SPC - 
 
 
From the main page of Freedom³ select the type of test to run “Process Capability” or “Cp/Cm”: 
 
 
 
 
 
 
 
Selecting  Process Capability, it will appear on the display: 
 
 
   
 
Freedom³ shows root and folders in the same way were created in SQ-net, but every single folder 
corresponds a single page on Freedom³. 
 
Press “right arrow” on Freedom³ keyboard to display next folder. 
 
  

Page 82

82 
 
 
The second level folder will appear (like SQ-net): 
 
  
 
 
 
 
Press again the “right arrow” on Freedom³ keyboard for third level folder: 
 
       
                      
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  

Page 83

 
 
   [email protected]     
83  
 
 
Pressing again “right arrow” Freedom³ will display tests regarding the specific location: 
 
 
 
 
Select the test by “Up” and “Down” arrows and press confirm on Freedom³ Keyboard. 
 
 
 
A new window will appear: 
 
 
 
 
 
TORQUE 
 
 
 
 
ANGLE 
 
 
 
The wrench is ready to tighten  
 
 
  

Page 84

84 
 
 
 
 
At the end of tightening Freedom³ will show the 
results:
 
The results in green color are inside tolerances, in red colors are outside. At the end of the test,  
Freedom³ will display the list of test related to the location with the status of last test: 
 
 
 
 
 
 
 
 
 
          
Number of tests done and 
grup size ( see paragrafh 
SPC QualityControl Test 
and SPC Production Tool 
Test) 
Message about status of 
measure  

Page 85

 
 
   [email protected]     
85  
How to run test from route - Freedom³ PRW - 
 
 
From main page of Freedom³ is possible to choose the type of test to run “Select Program” or 
“Select Hob”. 
Select Program -> If user wants select the operation to run one by one without following any 
sequence 
Select Job -> If user wants to follow a sequence of operation or only have a specific part of route 
test (group) 
 
 
Select Program 
On main page of Freedom³ touch “Select Program”: 
 
 
 
 
 
 
=f enabled,...

Page 86

86 
 
 
 
 
=n “Select Program” page is possible to select  from which operation user will start. 
 
 
 
 
 
 Operations 
 
 
 
 
 
 
 
 
 
 
 
Once the program is select press confirm on Freedom³ keyboard, the wrench is ready: 
 
 
       Number of test to do 
 
 
Operation name    
   Target and  
  tolerance  
    limits 
 
Units of measurements 
 
    Progression  
    bar 
 
 
 
 
     Message for operator 
 
 
Now operator can start to tighten up the target. 
 
 
 
  

Page 87

 
 
   [email protected]     
87  
If the torque and angle results will be in side tolerance limits, Freedom³ will display torque and 
angle value with green color. Otherwise, if torque or angle are outside of tolerance limits, the out 
value will be displayed with red color. In case torque and angle are out of tolerance limits, both 
will be displayed with red color. 
 
=n case of “Not OK” result Freedom³ will display a message “Confirm” pushing confirm button on 
keyboard or “Discard” pushing left...

Page 88

88 
 
 
 
=n the example above there is only one “Hob”, user can create more jobs in a route. 
 
Once the “Hob” is selected press confirm on Freedom³ keyboard to start the job. 
Depending from the sequence of every single operation (see paragraph, how create a route) 
Freedom³ will start the job from first operation and the operator must follow the sequence 
specified in the job. When all operation complete last “screw” of last operation Freedom³ will 
display the message “Hob completed”. 
 
During the...

Page 89

 
 
   [email protected]     
89  
When the Hob is finished, push on “ESC” keyboard button, to go back to main menu or select 
another job. =t’s also possible repeat the same job, Freedom³will store all data-results in the 
memory. For every test Freedom³ save data-results and curves (Torque/Time,Torque/angle). 
See paragraph “Freedom³ PRW “:ow to send data-results to SQnet”” 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  

Page 90

90 
 
Freedom³ SPC “How to send data results to SQ-Net” 
 
 
STEP -1- 
To send back data results  to SQ-Net user must connect Freedom³ to PC by USB 
cable 
 
             
             
             
        
        
        
       
        
        
        
  
 
 
 
STEP -2- 
Once USB cable is connected to computer and Freedom³, switch on Freedom³ and from the main 
page select “Synchronize” icon....
Start reading Aimco Brakes Freedom3 SPC Sqnet User Manual

Related Manuals for Aimco Brakes Freedom3 SPC Sqnet User Manual

All Aimco Brakes manuals