Yamaha 01v 96 I Manual

Using Libraries81
01V96i—Reference Manual
LibrariesEQ Library
This library enables you to store and recall EQ settings for 
Input Channels, Bus Outs 1–8, Aux Outs 1–8, and Stereo Out. 
The library contains 40 preset memories and 160 user (read-
able & writable) memories.
Follow the steps below to use the EQ library.
1.Press the DISPLAY ACCESS [EQ] button, then 
press the [F2] button.
The EQ | EQ Library page appears.
1CURRENT TYPE
This parameter displays the currently-selected channel 
EQ type (TYPE I or...

82Libraries
01V96i—Reference Manual
26Male Vocal 2A variation on preset 25.
27Female Vo. 1An EQ template for female vocals. Try adjusting the HIGH or HIGH-MID parameters according to the 
voice quality.
28Female Vo. 2A variation on preset 27.
29Chorus&HarmoAn EQ template for brightening choruses.
30To t a l  E Q  1Use on a stereo mix during mixdown. Sounds even better when used with a compressor.
31To t a l  E Q  2A variation on preset 30.
32To t a l  E Q  3A variation on preset 30. Can also be used with...

Remote Control83
01V96i—Reference Manual
Remote Control
Remote Control
This chapter describes the Remote function, which enables 
you to control external equipment directly from the 01V96i 
top panel.
About Remote Function
The 01V96i’s Remote function enables you to control external 
DAW (Digital Audio Workstation) equipment, MIDI devices, 
etc.
There are two types of Remote functions (Remote and 
Machine Control):
■REMOTE (Remote Layer)
To use these types of Remote functions, you must connect the...

84Remote Control
01V96i—Reference Manual
■Configuring Macintosh Computers
1.
Download the Yamaha Steinberg USB Driver 
from the following URL.
http://www.yamahaproaudio.com/
2.Install the driver in your computer as 
described in the installation guide included in 
the downloaded file.
3.Connect the 01V96i TO HOST USB port to a 
USB port on your Mac using a USB cable.
4.Make sure that the 01V96i is powered-on.
5.Launch Pro Tools.
6.Choose Peripherals from the Setups menu to 
open the Peripherals window....

Pro Tools Remote Layer85
01V96i—Reference Manual
Remote Control5.Press the DISPLAY ACCESS [DIO/SETUP] but-
ton repeatedly until the DIO/Setup | Remote 
page appears.
6.Select ProTools (as the target device) for the 
Target parameter (
1) located in the 
upper-right corner of the page.
By default, the Remote layer target is set to ProTools. If 
another target has been selected, rotate the Parameter 
wheel to select ProTools.
7.Press the LAYER [REMOTE] button.
The Remote Layer is now available for control,...

86Remote Control
01V96i—Reference Manual
5INSERT ASSIGN/EDIT section
This section enables you to insert plug-ins into Pro Tools 
channels and adjust plug-in settings. Use the left and right 
[ ]/[ ] Tab Scroll buttons to change the parameters 
displayed in this section.
•ASSIGN
Turn on this button to insert plug-ins into Pro Tools 
channels. (If you are using the TDM system, you can also 
assign outboard effects processors.)
•COMPARE
You can compare your edits with the original settings by 
turning on...

Pro Tools Remote Layer87
01V96i—Reference Manual
Remote ControlControl Surface Operation
When the Pro Tools Remote layer is selected, the 01V96i con-
trols on the top panel engage the following functions:
■Channel Strip section
• [SEL] buttons
These buttons select Pro Tools channels, inserts, and 
Automation mode. 
• [SOLO] buttons
These buttons solo Pro Tools channels. The button indi-
cators for the soloed channels light up.
•[ON] buttons
These buttons mute Pro Tools channels. 
•Faders
The faders set...

88Remote Control
01V96i—Reference Manual
DAW REWFast rewinds the cursor position.
DAW SHUTTLESwitches the Wheel mode to Shuttle.
DAW SCRUBSwitches the Wheel mode to Scrub 
(Jog).
DAW AUDITIONYou can audition the pre-roll, 
post-roll, in-point area, or out-point 
area by holding down the button to 
which this function is assigned and 
pressing a button to which DAW 
PRE, DAW POST, DAW IN, or DAW 
OUT is assigned.
DAW PREPlays back from the pre-roll point up 
to the beginning of the selected 
area.
DAW...

Pro Tools Remote Layer89
01V96i—Reference Manual
Remote Control
Selecting Channels
To select a single Pro Tools channel, press the [SEL] button 
that corresponds to the desired channel.
To select multiple Pro Tools channels simultaneously, while 
holding down one [SEL] button, press the [SEL] buttons of 
the other channels you wish to add. Press the [SEL] buttons 
again to cancel the selection.
Setting Channel Levels
1.Make sure that the FADER MODE [HOME] 
button indicator is lit steadily.
If the...

90Remote Control
01V96i—Reference Manual
Soloing Channels
To solo Pro Tools channels, press the [SOLO] buttons of the 
desired channels. Grouped channels are soloed together, and 
other channels are muted.
Press the [SOLO] buttons again to unsolo the channels.
Configuring Sends A–E as Pre or 
Post
You can set Pro Tools channels for the selected Sends (A–E) 
to pre or post.
1.Press the [F3] button to select Channel Dis-
play mode.
2.Press the FADER MODE [AUX 1]–[AUX 5] but-
tons to select the desired...