Yamaha 01v 96 I Manual

Setting the Stereo Out and Bus Out 1–8 from the Display31
01V96i—Reference Manual
Bus OutsEQ’ing the Stereo Out and Bus 
Outs
To set the EQ for the Stereo Out and Bus Out 1–8 EQ, press 
the DISPLAY ACCESS [EQ] button, then press the [F1] but-
ton to display the EQ | EQ Edit page, and use the [SEL] but-
tons to select the Stereo Out or Bus Out 1–8.
The parameters on this page (and the procedure for setting 
them) are the same as for Input Channels (see page 21). Note 
that the Stereo Out does not feature...

32Bus Outs
01V96i—Reference Manual
■Viewing Faders and Other 
Parameters
To display the View | Fader page, use the corresponding [SEL] 
button to select the desired bus, then press the DISPLAY 
ACCESS [VIEW] button, then press the [F2] button.
The Fader page layouts for Stereo Out and Bus Out 1–8 are 
slightly different.
Stereo Out Fader page
1BAL
This control adjusts the level balance between the L and R 
channels of the Stereo Out.
2ON/OFF
This button turns the Stereo Out on or off, and links with 
the...

Setting the Stereo Out and Bus Out 1–8 from the Control Surface33
01V96i—Reference Manual
Bus Outs
Setting the Stereo Out 
and Bus Out 1–8 from the 
Control Surface
You can use the faders, [SEL] buttons, and various buttons 
and controls in the SELECTED CHANNEL section on the 
top panel to directly control certain parameters for the Stereo 
Out and Bus Out 1–8.
Setting the Levels
Move the [STEREO] fader to adjust the Stereo Out levels. 
Press the [ON] button in the STEREO section to turn the Ste-
reo Out...

34Bus Outs
01V96i—Reference Manual
2F. S
This button determines whether Aux Sends follow the 
Input Channel Surround Pan when the 01V96i is in any 
Surround mode other than “Stereo.” When this button is 
turned on, Aux Sends follow the Input Channel Surround 
Pan. This is useful for feeding Surround signals to exter-
nal Surround effects processors.
2.Move the cursor to the MONOx2 button for 
the desired Bus or Aux Send, then press 
[ENTER].
The buses or Aux Sends are paired.
3.To cancel a pair, move the...

Naming the Stereo Out and Bus Outs35
01V96i—Reference Manual
Bus Outs
Naming the Stereo Out 
and Bus Outs
You can change the default Bus names (BUS1, AUX4, STE-
REO, etc.). It may be convenient to name the buses “Monitor 
Out” or “Effect Send,” for example, so that you can easily iden-
tify the signal type.
1.Press the DISPLAY ACCESS [PATCH] button 
repeatedly until the Patch | Out Name page 
appears.
You can specify Short names in the center column (1) 
and Long (full) names in the right column (
2)....

36Aux Outs
01V96i—Reference Manual
Aux Outs
This chapter describes how to control Aux Out 1–8.
Aux Out 1–8
The Aux Out 1–8 section mixes signals routed from the Input 
Channels to the corresponding Aux Sends, processes them 
using on-board EQ, compressor, etc., then routes them to the 
specified internal effects processors, output connectors or I/O 
card connectors.
The 01V96i features eight Aux Sends, which can be used to 
send signals to the internal and external effects processors 
and monitors.
The...

Setting Aux Out 1–8 from the Display37
01V96i—Reference Manual
Aux OutsDelaying Aux Outs
To delay Aux Out 1–8 signals, press the DISPLAY ACCESS 
[ /INSERT/DELAY] button repeatedly until the 
/INS/DLY | Out Dly page appears.
The parameters on this page (and the procedure for setting 
them) are the same as for Input Channels, except that this 
page does not include the MIX/FB.GAIN parameters (see 
page 18).
Comp settings
To set the Aux Out 1–8 compressors, press the DISPLAY 
ACCESS [DYNAMICS] button, then...

38Aux Outs
01V96i—Reference Manual
■Viewing Faders and On/Off 
Parameters
To display the View | Fader page, use the corresponding [SEL] 
button to select the desired Aux Out (1–8), then press the DIS-
PLAY ACCESS [VIEW] button, then press the [F2] button.
•ON/OFF
This button turns the currently-selected Aux Out (1–8) 
on or off. It links with the corresponding [ON] (1–8) but-
ton in the Master layer.
•Fader
This fader sets the currently-selected Aux Out (1–8) level. 
It links with the corresponding fader...

Setting Aux Send Levels39
01V96i—Reference Manual
Aux Outs
3.Move the cursor to the FIXED or VARIABLE 
button in the MODE section for the cur-
rently-selected Aux Send to select a mode.
•Fixed Mode
In this mode, Aux Send levels are fixed at nominal 
(0.0 dB). Also, channel ON/OFF buttons appear instead 
of the Send level rotary controls and PRE/POST buttons.
•Variable Mode
In this mode, Aux Send levels are variable and the signal 
source point can be either pre-fader or post-fader. Chan-
nel Send level...

40Aux Outs
01V96i—Reference Manual
Viewing Aux Send 
Settings for Multiple 
Channels
You can view and set parameters for all Aux Send 1–8, includ-
ing setting levels and Pre/Post parameters.
This is convenient when you wish to visually check all Aux 
Send settings or simultaneously adjust the levels of certain 
channels routed to Aux 1–8.
1.Press one of the FADER MODE [AUX 1]–[AUX 
8] buttons repeatedly until the page listed 
below that contains the desired channels 
appears.
• View1-16 page
This page...