Yamaha 01v 96 I Manual

Rear Panel11
01V96i—Reference Manual
Control Surface & Rear PanelSLOT Section
1SLOT
Power Section
1POWER ON/OFF switch
2AC IN connector
1
21 

12Analog I/O & Digital I/O
01V96i—Reference Manual
Analog I/O & 
Digital I/O
This chapter describes the 01V96i’s analog and digital 
input/output connectors as well as the basic operations 
involving the digital I/Os.
Analog Inputs & Outputs
Input Section
The 01V96i’s top panel features input connectors, which 
enable you to connect microphone and line-level sources. 
• INPUT connectors A 1–12
These balanced TRS-type 
phone connectors accept 
line-level and microphone sig-
nals. The nominal input range...

Digital Inputs & Outputs13
01V96i—Reference Manual
Analog I/O & Digital I/OOutput Section
The 01V96i top and rear panels feature output connectors 
that enable you to connect a monitoring system, effects pro-
cessors and other line-level devices.
• MONITOR OUT connectors L/R
These balanced TRS-type phone con-
nectors output monitoring signals or 
input signals routed from the 2TR IN 
connectors. The nominal output level 
is +4 dB.
Use the Monitor source selector in the Monitor Out & 
Headphones section...

14Analog I/O & Digital I/O
01V96i—Reference Manual
Converting Sampling 
Rates of Signals Received 
at I/O Card Inputs
An optional MY8-AE96S Digital I/O card features sampling 
rate converters, so you can easily convert the sampling fre-
quency of digital inputs to the current 01V96i sampling rate.
1.Press the DISPLAY ACCESS [DIO/SETUP] but-
ton repeatedly until the DIO/Setup | Format 
page appears.
Use the buttons in the SRC sections to turn the sampling 
rate converters on and off. You can turn the...

Dithering Digital Outputs15
01V96i—Reference Manual
Analog I/O & Digital I/O
6COPY
Indicates the status of copy protection information 
included in the IEC958 Part2 (S/PDIF-Consumer) for-
mat signals. “OK” appears if copying is allowed. “Pro-
hibit” appears if copy-protected.
3.If you select the SLOT 
button for a slot that 
has an MY16-AE card installed, use the 01–08 
and 09–16 buttons located in the lower-right 
corner of the screen to select a channel group 
you wish to display.
Dithering Digital...

16Analog I/O & Digital I/O
01V96i—Reference Manual
Setting the Transfer 
Format for Higher 
Sampling Rates
To operate the 01V96i at higher sampling frequencies 
(88.2 kHz or 96 kHz) and transfer digital audio signals to and 
from connected external devices, you must set the data trans-
fer format in accordance with the sampling frequencies sup-
ported by the external devices.
1.Press the DISPLAY ACCESS [DIO/SETUP] but-
ton repeatedly until the DIO/Setup | Word 
Clock page appears.
2.Select INT88.2k or...

Input Channels17
01V96i—Reference Manual
Input Channels
Input Channels
This chapter describes how to adjust the 01V96i’s Input 
Channel parameters.
About Input Channels
The input Channel section enables you to adjust the level and 
tone of the signals input to the 01V96i (and the signals output 
from the internal Effects processors 1–4), and route the sig-
nals to Buses 1–8, the Stereo Bus, and Aux Sends 1–8. There 
are two types of Input Channels, each featuring slightly differ-
ent functions: monaural...

18Input Channels
01V96i—Reference Manual
Setting the Input 
Channels from the 
Display
To set the Input Channel parameters, you can either move the 
cursor to the desired parameter on the display and change the 
value, or operate the desired button or control on the top 
panel to directly change the setting.
This section explains how to set the parameters via the dis-
play.
Switching the Signal Phase
To switch the phase of each Input Channel, press the 
[ /INSERT/DELAY] button repeatedly until the...

Setting the Input Channels from the Display19
01V96i—Reference Manual
Input Channels•MIX
This parameter sets the mix balance of dry (Input Chan-
nel) and wet (delayed) signals.
•FB.GAIN
This parameter sets the amount of delay feedback.
Gating Input Channels
To set the Input Channel gates, use the [SEL] buttons to select 
the desired Input Channel, then press the DISPLAY ACCESS 
[DYNAMICS] button, then press the [F1] button. The 
Dynamics | Gate Edit page appears.
1KEYIN SOURCE
Select one of the following...

20Input Channels
01V96i—Reference Manual
Compressing Input Channels
To set the Input Channel compressors, use the [SEL] buttons 
to select the desired Input Channel, then press the DISPLAY 
ACCESS [DYNAMICS] button, then press the [F3] button to 
display the Dynamics | Comp Edit page.
1POSITION
Use the Parameter wheel, or the [INC]/[DEC] buttons to 
select the position of the compressor within the channel 
from the following options:
•PRE EQ.................... Immediately before EQ (default)
•PRE...