Xerox WorkCentre 3045 Service Manual

4
Chapter
Service Parts 
Disassembly
In this chapter...
•Overview
• Consumable
• Phaser 3010/3040 Covers
• Phaser 3010/3040 Feeder
• Phaser 3010/3040 Xerographics
• Phaser 3010/3040 Drive
• Phaser 3010/3040 Electrical
• WorkCentre 3045 Covers
• WorkCentre 3045 Feeder
• WorkCentre 3045 Xerographics
• WorkCentre 3045 Drive
• WorkCentre 3045 Electrical
• WorkCentre 3045 Scanner and ADF 

4-2 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Overview
This section contains the removal procedures for field-replaceable parts listed in 
the Parts List. In most cases, the replacement procedure is simply the reverse of 
the removal procedure. In some instances, additional steps are necessary and are 
provided for replacement of the parts. For specific assemblies and parts, refer to 
Chapter 9.
Standard Orientation of the Printer
When needed, the...

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-3Service Parts Disassembly
Preparation
Before you begin any procedure:
Wa rn i n g
Unplug the power cord from the wall outlet.
Wa rn i n g
Allow the Fuser to cool before using the procedure.
Caution
Many parts are secured by plastic tabs. Do not over flex or force these parts. 
Do not over torque screws threaded into plastic.
Note
Names of parts that appear in the removal procedures may not match the 
names that appear in the Parts List....

4-4 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Fastener Types
The following table lists the types of screws used to assemble the printer. The 
procedures provide dimensions for screws being removed.
Caution
Use care when installing self-tapping screws in plastic. To properly start the 
screw in plastic, turn the screw counter-clockwise in the hole until you feel the 
screw engage the threads, then tighten as usual. Improperly aligning or over...

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-5Service Parts Disassembly
Consumable
The Toner Cartridge is the only consumable.
Toner Cartridge
PL4.1.13
1. Open the Main Tray Door
2. Open the Toner Door.
3. Turn the Toner Cartridge handle CCW to release the lock and remove the 
cartridge.
s3040-013 

4-6 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Phaser 3010/3040 Covers
Output Tray Extension
PL1.1.1
1. Open the Output Tray Extension.
2. Release the boss of the Output Tray Extension from the hole on the Top Cover.
s3040-015 

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-7Service Parts Disassembly
To p  C o v e r
PL1.1.4
1. Open the Rear Door.
2. Remove the Main Tray (page 4-13).
3. Remove the Front Cover (page 4-15).
4. Remove the Right Cover (page 4-12).
5. Remove the Left Cover (page 4-16)
6. Remove the Output Tray Extension (page 4-6).
7. Release the front tabs, and carefully lift the Top Cover from the right and 
disconnect P/J220 on the Control Panel to remove the Top Cover.
s3040-023 

4-8 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Rear Door
PL1.1.8
1. Open the Rear Door.
2. Release the boss from the right hinge and remove the Rear Door.
s3040-017 

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-9Service Parts Disassembly
Transfer Roller Bearings
PL1.1.9, 1.1.10
1. Open the Rear Door.
2. Release the bearing locks and rotate the bearings to align the key with the 
notch and remove the bearings from the Transfer Roller shaft.
s3040-024 

4-10 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Transfer Roller
PL1.1.11
1. Open the Rear Door.
2. Remove the right side Transfer Roller bearing (page 4-9) and remove the 
Transfer Roller from the Rear Door.
s3040-024