Xerox Phaser 8860DN User Manual

Printing on Specialty Media
Phaser® 8560/8860 Printer
3-35 2.Insert transparencies into the tray.
Note: Do not load transparencies above the paper fill line inside the tray. 
8860p-102
8860p-103
Downloaded From ManualsPrinter.com Manuals 

Printing on Specialty Media
Phaser® 8560/8860 Printer
3-36 3.Adjust the paper guides to fit the transparencies (if necessary).
■Length guide: Press the sides, then slide the guide until the arrow on the guide points 
to the appropriate paper size imprinted on the bottom of the tray. When properly 
positioned, the guide clicks into place.
■Width guides: Slide the width guides until the arrows on the guides point to the 
appropriate paper size labeled on the bottom of the tray. When properly positioned,...

Printing on Specialty Media
Phaser® 8560/8860 Printer
3-37 4.Insert the tray into the tray slot, and then push it completely into the printer. 
5.On the control panel:
a.Select 
Paper Tray Setup, and then press the OK button.
b.Select either 
Tr a y  2  P a p e r  Ty p e, Tr a y  3  P a p e r  Ty p e, or Tray 4 Paper Type, and then 
press the OK button.
c.Select 
Transparency, and then press the OK button.
6.In the printer driver, select either Tr a n s p a r e n c y as the paper type or the appropriate...

Printing on Specialty Media
Phaser® 8560/8860 Printer
3-38
Printing Envelopes
Envelopes can be printed from any tray depending on the type of envelope you are using. 
See also: 
Supported Paper Sizes and Weights for Tray 1 on page 3-6
Supported Paper Sizes and Weights for Tray 2, 3, or 4 on page 3-8
Guidelines
■Use only paper envelopes specified in the Supported Papers table. Successful envelope 
printing is highly dependent on the quality and construction of the envelopes. 
■Maintain constant...

Printing on Specialty Media
Phaser® 8560/8860 Printer
3-39
Printing Envelopes from Tray 1
To print envelopes:
1.Pull down and out on the handle to open Tray 1.
2.Open the tray extension.
8860p-006
8860p-007
Downloaded From ManualsPrinter.com Manuals 

Printing on Specialty Media
Phaser® 8560/8860 Printer
3-40 3.Insert a maximum of 10 envelopes into the tray and adjust the paper guides to fit the 
envelopes:
■Side-flap envelopes: Insert the envelopes with the flap side up and the flap of the 
envelopes toward the left side of the tray.
■End-flap envelopes: Fold down the flaps before placing them in the tray. Insert the 
envelopes with the flap side up and the flap entering the printer first.
8860p-010
8860p-091
Downloaded From ManualsPrinter.com Manuals 

Printing on Specialty Media
Phaser® 8560/8860 Printer
3-41 4.On the control panel, press the OK button if the correct envelope size and type are 
displayed as the current setup, or select 
Change setup, and then press the OK button.
■If your envelope size is displayed in the list, select it, and then press the OK button. 
Go to Step 7.
■If your envelope size is not displayed in the list, select New Custom Size, and then 
press the OK button. 
5.Select one of the following Short Edge options:
■Press the...

Printing on Specialty Media
Phaser® 8560/8860 Printer
3-42
Printing Envelopes from Tray 2, 3, or 4
To print envelopes:
1.Remove the tray from the printer.
2.Insert a maximum of 40 envelopes into the tray, flap side down with the flap toward the 
left side of the tray.
3.Adjust the paper guides to fit the envelopes.
8860p-002
8860p-109
Downloaded From ManualsPrinter.com Manuals 

Printing on Specialty Media
Phaser® 8560/8860 Printer
3-43
■Length guide: Press the sides, then slide the guide until the arrow on the guide points 
to the appropriate paper size imprinted on the bottom of the tray. When properly 
positioned, the guide clicks into place.
■Width guides: Slide the width guides until the arrows on the guides point to the 
appropriate paper size labeled on the bottom of the tray. When properly positioned, 
the guides click into place. 
Note: When the paper guides are...

Printing on Specialty Media
Phaser® 8560/8860 Printer
3-44 4.Insert the tray into the tray slot, and then push it completely into the printer.
5.On the control panel:
a.Select 
Paper Tray Setup, and then press the OK button.
b.Select either 
Tr a y  2  P a p e r  Ty p e, Tr a y  3  P a p e r  Ty p e, or Tray 4 Paper Type, and then 
press the OK button.
c.Select 
Envelope and then press the OK button.
6.In the printer driver, select either Envelope as the paper type or the appropriate tray as the 
paper...