Xerox Phaser 6115MFP User Manual

Loading Media
Phaser® 6115MFP Multifunction Product
6-7 To load paper in Tray 1:
1.Remove the lid from Tray 1.
2.If loading paper longer than A4/Letter, open the front panel of the tray.
3.Slide apart the media guides to provide more space between them.
6115-012
6115-098
6115-013
Downloaded From ManualsPrinter.com Manuals 

Phaser® 6115MFP Multifunction Product
6-8 4.Load the paper face-up in the tray.
Caution:Do not load paper or media above the fill line indicated on the tray. Overloading 
the tray may cause jams.
6115-014
6115-015
Downloaded From ManualsPrinter.com Manuals 

Loading Media
Phaser® 6115MFP Multifunction Product
6-9 5.Adjust the paper guides to fit the paper loaded in the tray (if necessary).
6.Close the front panel of Tray 1, and then replace the lid.
6115-016
6115-017
Downloaded From ManualsPrinter.com Manuals 

Loading Media
Phaser® 6115MFP Multifunction Product
6-10
Card Stock
Test all card stock to ensure acceptable performance and to ensure that the image does not 
shift. Use card stocks that are approved for laser printers.
Do not use card stocks that are:
■Coated
■Designed for inkjet printers
■Precut or perforated
■Preprinted or multicolored
■Folded, wrinkled, creased or warped
■Mixed with any other media in the trays, this will cause misfeeding.
Thick Card Stock
Paper thicker than 90 g/m2 (24 lb. bond) is...

Loading Media
Phaser® 6115MFP Multifunction Product
6-11
Loading Envelopes
Print on the front (address) side only. Some parts of the envelope consist of three layers of 
paper: the front, back, and flap. Anything printed on these layered regions may be lost or 
faded.
Caution:Envelopes require you to adjust the product’s fuser. Follow the instructions for 
loading envelopes to avoid damaging the product. 
Use envelopes that are:
■Common office envelopes with diagonal joints, sharp folds and edges, and...

Loading Media
Phaser® 6115MFP Multifunction Product
6-12 To load envelopes in Tray 1:
1.Remove the lid from Tray 1.
2.Open the front panel of the tray, if necessary.
3.Remove any media from the tray.
Note:Before loading envelopes, press them down to make sure that all the air is removed, 
and make sure that the folds of the flaps are firmly pressed; Otherwise, the envelopes may 
become wrinkled and a paper jam can occur.
6115-012
6115-098
Downloaded From ManualsPrinter.com Manuals 

Loading Media
Phaser® 6115MFP Multifunction Product
6-13 4.Slide the media guides open.
5.Load the envelopes as shown.
■For envelopes with the flap along the long edge, load the envelopes with the flap 
toward the left of the product.
6115-013
6115-019
Downloaded From ManualsPrinter.com Manuals 

Loading Media
Phaser® 6115MFP Multifunction Product
6-14
■For envelopes with the flap along the short edge, load the envelopes with the flap 
entering the product first.
6.Slide the media guides against the edge of the envelopes.
7.Close the Tray 1 front panel, and then replace the lid.
6115-018
6115-020
6115-017
Downloaded From ManualsPrinter.com Manuals 

Loading Media
Phaser® 6115MFP Multifunction Product
6-15 8.Ensure the automatic document feeder is closed.
9.Release the scanner latch and lift the scanner unit.
6115-102
6115-021
Downloaded From ManualsPrinter.com Manuals 

Loading Media
Phaser® 6115MFP Multifunction Product
6-16 10.Pull the lever, and then open the top cover.
Caution:Do not touch the transfer belt.
11.Raise both green fuser separator levers.
6115-022
6115-023
Downloaded From ManualsPrinter.com Manuals