Xerox DocuColor 12 User Manual

							DOCUCOLOR 12 USER GUIDE5–15 ADDED FEATURES
1
2
3
4
5
6
7
3Perform one of the following:
•To scan and copy both pages, touch the Both 
Pages icon.
•To scan and copy the top page without the 
bottom page, touch the Top Page Only icon. 
•To scan and copy the bottom page without the 
top page, touch the Bottom Page Only icon.
4If necessary, use the arrows under the Binding 
Erase icon to delete the centre shadow from the 
output. Touch the right arrow to increase the 
amount of erasure in the centre of the output copy. 
Touch the left arrow to decrease the amount of 
erasure in the centre of the output copy. Binding 
Erase values range from 0 to 50 mm.
Notice that the values in the box increase or 
decrease according to your selection.
5Use the diagram on the screen when you place 
the original onto the Document Glass to ensure 
expected results.
The bound document should be placed face down 
with the upper left corner of the top page in the 
upper left corner of the Document Glass.
6Touch Save to return to the Added Features tab.
Downloaded From ManualsPrinter.com Manuals 
						

							ADDED FEATURES5–16 DOCUCOLOR 12 USER GUIDE
1
2
3
4
5
6
7
Margin Shift
The Margin Shift feature (Figure 14) allows you to 
change the placement of an image on the output 
page.
You can move images to the centre of the output 
or move them to a specific corner or edge. In 
addition, you can specify variable incremental 
shifts toward any margin.
This section describes the following options 
illustrated in Figure 15:
•No Shift
•Auto Centre
•Corner Shift
•Variable Shift
NOTE:You can select only one shift option at any 
time for each side.
After you have selected a Margin Shift option, the 
Added Features screen displays a check in the 
feature check box beside the set values.
Figure 14: Margin Shift feature
Figure 15: Margin Shift screen
Downloaded From ManualsPrinter.com Manuals 
						

							DOCUCOLOR 12 USER GUIDE5–17 ADDED FEATURES
1
2
3
4
5
6
7 No Shift
If No Shift is selected, the copier/printer assumes 
that the original document is registered in the 
upper left corner of the Document Glass. If the 
document is offset from this registration point, the 
image on the output copy will be offset by the 
same amount.
1Touch the Margin Shift icon on the Added 
Features tab to display the Margin Shift screen, 
Figure 16.
2Touch either the Side 1 or Side 2 icon to display 
the Margin Shift screen for the desired side.
3Touch the No Shift icon, as in Figure 17.
4Touch Save to return to the Margin Shift screen.
5If desired, repeat steps 2-4 to adjust the Margin 
Shift for the other side.
6Touch the icon that most closely resembles the 
Original Orientation for the document on the 
Document Glass.
7Touch Save to return to the Added Features tab.
Figure 16: Margin Shift screen
Figure 17: Margin Shift screen with No Shift 
selected
Downloaded From ManualsPrinter.com Manuals 
						

							ADDED FEATURES5–18 DOCUCOLOR 12 USER GUIDE
1
2
3
4
5
6
7 Auto Centre
Selecting the Auto Centre option centres the 
original image on the output page, as illustrated in 
Figure 18.
KEY POINT:The Auto Centre option is not 
available for 12 x 18 inch or SRA3 originals that 
are being copied without reduction.
The Auto Centre option is intended for copying 
original documents that are smaller than the copy 
paper. You can also use this feature when you 
select a reduction value for original documents 
that are larger than the copy paper selected. 
NOTE:In some cases, the original image centre 
will be shifted slightly on the output copy.
The orientation of the output image is determined 
by the placement of the document on the 
Document Glass and the orientation of the 
selected paper supply.
The copier/printer completes a prescan to 
determine the size of the document.
Figure 18: Example of Auto Centre
Downloaded From ManualsPrinter.com Manuals 
						

							DOCUCOLOR 12 USER GUIDE5–19 ADDED FEATURES
1
2
3
4
5
6
7
1Touch the Margin Shift icon on the Added 
Features tab to display the Margin Shift screen, as 
illustrated in Figure 19.
2Touch either the Side 1 or Side 2 icon to display 
the Margin Shift screen for the desired side.
3Touch the Auto Centre icon to display the Auto 
Centre detail screen, as illustrated in Figure 20.
4Touch Save to return to the Margin Shift screen.
5If desired, repeat steps 2-4 for the other side.
6Touch the icon that most closely resembles the 
Original Orientation for the document on the 
Document Glass.
7Touch Save to return to the Added Features tab.
Figure 19: Margin Shift screen
Figure 20: Margin Shift screen with
Auto Centre selected
Downloaded From ManualsPrinter.com Manuals 
						

							ADDED FEATURES5–20 DOCUCOLOR 12 USER GUIDE
1
2
3
4
5
6
7 Corner Shift
Select the Corner Shift feature to move the image 
to a specified edge or corner on the output copy 
for Side 1 or 2, as illustrated in Figure 21.
This feature works in three ways:
•To shift an image on small documents to a 
specified corner on the output
•To be used with the Reduction feature to 
designate a position where the reduced image 
is to appear on the output
•To be used with the Enlarge feature to 
designate a position where the enlarged 
image is to appear on the output
NOTE:Corner Shift may not be evident on your 
output if you copy your original document at 
100%.
The orientation of the image on the copies is 
determined by the placement of the document on 
the Document Glass and by the orientation of the 
selected paper supply.
The copier/printer completes a prescan to 
determine the size of the document.
Figure 21: Example of Corner Shift
Downloaded From ManualsPrinter.com Manuals 
						

							DOCUCOLOR 12 USER GUIDE5–21 ADDED FEATURES
1
2
3
4
5
6
7
1Touch the Margin Shift icon on the Added 
Features tab to display the Margin Shift screen as 
illustrated in Figure 22.
2Touch either the Side 1 or Side 2 icon to display 
the Margin Shift screen for the desired side.
3Touch the Corner Shift icon to display the Corner 
Shift detail screen, as illustrated in Figure 23.
4Touch the arrow icon that illustrates the desired 
location of the image on the output copy.
5Touch Save to return to the Margin Shift screen.
6If desired, repeat steps 2-5 for the other side.
7Touch the icon that most closely resembles the 
Original Orientation for the document on the 
Document Glass.
8Touch Save to return to the Added Features tab.
Figure 22: Margin Shift screen
Figure 23: Margin Shift screen with
Corner Shift selected
Downloaded From ManualsPrinter.com Manuals 
						

							ADDED FEATURES5–22 DOCUCOLOR 12 USER GUIDE
1
2
3
4
5
6
7 Variable Shift
The Variable Shift option enables you to adjust the 
horizontal or vertical orientation of the output 
image, as illustrated in Figure 24. You can shift the 
image up, down, right, or left by means of the 
variable arrow buttons.
You can designate the variable shift in 1 mm 
increments, from 0 to 432 mm.
NOTE:Do not use Variable Shift if you want 
100% of your original document to be copied.
The orientation of the image on the copies is 
determined by the placement of the document on 
the Document Glass and by the orientation of the 
selected paper supply.
Figure 24: Example of Variable Shift
Downloaded From ManualsPrinter.com Manuals 
						

							DOCUCOLOR 12 USER GUIDE5–23 ADDED FEATURES
1
2
3
4
5
6
7
1Touch the Margin Shift icon on the Added 
Features tab to display the Margin Shift screen, as 
illustrated in Figure 25.
2Touch either the Side 1 or Side 2 icon to display 
the Margin Shift screen for the desired side.
3Touch the Variable Shift icon to display the 
Variable Shift detail screen, as illustrated in
Figure 26.
4Perform one or both of the following:
•Under the Left & Right icon, touch the right 
arrow to shift the image toward the right edge. 
Touch the left arrow to shift the image toward 
the left edge. Continue to touch the 
appropriate arrow until you have specified the 
desired amount of shift from 0 to 432 mm.
•Under the Up & Down icon, touch the up 
arrow to shift the image toward the top edge. 
Touch the down arrow to shift the image 
toward the bottom edge. Continue to touch 
the appropriate arrow until you have specified 
the desired amount of shift from 0 to 432 mm.
Notice that the values in the box increase or 
decrease according to your selection and that the 
icon illustrates the direction of the shift.
Figure 25: Margin Shift screen
Figure 26: Margin Shift screen with
Variable Shift selected
Downloaded From ManualsPrinter.com Manuals 
						

							ADDED FEATURES5–24 DOCUCOLOR 12 USER GUIDE
1
2
3
4
5
6
7
5Touch Save to return to the Margin Shift screen.
6If desired, repeat steps 2-5 for the other side.
7Touch the icon that most closely resembles the 
Original Orientation for the document on the 
Document Glass.
8Touch Save to return to the Added Features tab.
Downloaded From ManualsPrinter.com Manuals