Xerox 6279 User Manual

4.Using either the scroll buttons or the numeric keypad, select the desired setting, and
then select Save.
5.Select Save on the Set Timeout Durations screen to return to the Control Panel screen.
NOTE
The Sleep Mode setting cannot be less than the Low-Power Mode setting.
NOTE
In European Markets, the legally mandated EMC directive is to keep the sleep
timeout setting below 1 hour (60 minutes).
3-17Xerox® 6279® Wide Format Solution
Printer User Guide
System Administration
Downloaded From...

Features Timeout
The Feature Timeout option controls how long the current feature parameters will remain
in effect after the user has made a selection. The Feature timer can be set between 0
and 99 minutes. The default value for this feature is 5 minutes.
1.Select Control Panelfrom the Administration tab.
2.Select Configure Timers....
The Set Timeout Durationsscreen displays.
3.Select Features Timeout.
The Set Timeout Durations Feature Timeoutscreen displays.
Xerox® 6279® Wide Format Solution3-18
Printer...

4.Using either the scroll buttons or the numeric keypad, select the desired setting, and
then select Save.
5.Select Save on the Set Timeout Durations screen to return to the Control Panel screen.
File Deletion Timeout
The file deletion timeout feature is enabled when the user wishes to keep a specific file
for a period longer than 24 hours.
1.Select Control Panel from the Administration tab.
2.Select Configure Timers . .
The Set Timeout Durations screen displays.
3.Select File Deletion Timeout
The File...

6.Select Print Interrupt Timeout
The Print Interrupt Timeout screen displays.
7.Using either the scroll buttons or the numeric keypad, select the desired setting, and
then select Save.
8.Select Save to return to the Control Panel screen.
Calibrate Touch Screen
Your User Interface Touch Screen is calibrated when it is installed. Calibration aligns the
cursor to the place on the screen that you touch. The user interface does not typically
need to be recalibrated, unless it is not working correctly or you...

For more information on DHCP, see the Setting Up DHCP section of this chapter for
details.
If you are not already logged in as System Administrator, you are prompted for the
Administrator password when you select Network Setup. Contact your System
Administrator for the password if required.
NOTE
Whether you enter the network settings using the Web Printer Management
Tool or the User Interface, entering them in one place affects the other.
4.Select Machine Info from the Services menu.
5.Select the...

NOTE
Make sure the DHCP checkbox is not checked. Otherwise the IP Address, Gateway
and Netmask options cannot be selected.
3.Use the numeric touch pad to enter the IP Address in the format nn.nnn.nn.nnn.
4.Select Enter.
Setting up IP Gateway
1.Select the Services button on the Control Panel, followed by Machine Info
 > Administration Tab > Network Setup.
2.Select Gateway from the Network Setup screen.
The IP Gateway screen displays.
3.Enter the Gateway in the format XXX.XXX.XXX.XXX.
4.Select Enter....

Setting up Netmask
1.Select the Services button on the Control Panel, followed by Machine Info
 > Administration Tab > Network Setup.
2.Select Netmask from the Network Setup screen.
The IP Netmask screen displays.
3.Enter the Subnet Mask in the format XXX.XXX.XXX.XXX.
4.Select Enter.
The Network Setup screen displays.
5.Select Save.
Setting up DHCP
If you are unaware of the IP Address, Gateway, or Subnet Mask information, you can
utilize the Dynamic Host Configuration Protocol (DHCP) option. When this...

2.Select the DHCP checkbox.
This will disable the IP Address, Gateway, and Netmask fields.
3.Select Save to return to the Administration tab.
It is recommended that you reboot the controller after changing to the DHCP option.
If you choose to set up the network settings using the Web Printer Management Tool,
refer to the Web Printer Management Tool online Help or the FreeFlow Accxes Print
Server and Web Printer Management Tool Setup Guide for more information.
NOTE
When configuring a network connection...

4
Machine Information
This chapter describes the features available within the Machine Information screen. A
quick overview of each of the Machine Information tabs is provided, followed by the
detailed steps to access and modify settings to meet your requirements.
The Machine Info option accessed through the Services Menu contains the following
options:
•Machine Information
•Print Reports
•Machine Configuration
•Job Information
•Administration
The following areas will be defined further:
•Media Status...

2.Select Machine Infoon the Services Menu.
The screen displays the following fields of information:
Linear Usage
This is the amount of media that has passed through the machine.
Area Usage
This is the media used in square foot measurement.
Control SW (Software Version)
The FreeFlow Accxes Controller Server software version will be displayed here.
IP Address
The IP Address will be displayed with IPv4 first and then the IPv6 addresses. The IPv6
addresses will be listed with their scope (Global or Site)....