Xerox 6279 User Manual

8.Rotate the Media Roll until the lead edge of the paper is gripped in the Feed Roll
Area. The roll will feed and stop automatically.
9.Press the Media Advance button corresponding to the Media Roll and release it to
cut the lead edge and position the media into the feeder.
NOTE
If you wish to cut a longer length of the roll, press and hold the Media Advance
button.
10.Remove the trimmed piece of paper from the Cutter Area.
1-25Xerox® 6279® Wide Format Solution
Printer User Guide
Product Overview...

11.Gently close the Media Drawer until it latches.
Cutting the Media Roll
If the lead edge of the media becomes damaged after it is loaded, follow the procedure
below.
1.Open the Media Drawer.
2.If the lead edge of the media is folded or badly damaged in any way, rewind the
media on the roll from which the jam has occurred by rotating it towards you.
3.Pull the desired amount of damaged paper out toward you and cut with scissors.
Xerox® 6279® Wide Format Solution1-26
Printer User Guide
Product Overview...

4.Feed the paper’s lead edge until it is gripped in the Feed Roll Area. The roll will feed
and stop automatically.
5.Press the Media Advance button corresponding to the media roll and release it to
cut the lead edge and position the media into the feeder.
NOTE
If you wish to cut a longer length of the roll, press and hold the Media Advance
button.
6.Remove the trimmed piece of paper from the Cutter Area.
1-27Xerox® 6279® Wide Format Solution
Printer User Guide
Product Overview
Downloaded From...

7.Gently close the Media Drawer until it latches.
Loading Cut Sheet Media
1.Slowly pull out the Media Tray towards you until it stops.
2.Load the paper in the tray. Do not fill above the Max Fill Line on the back of the tray.
3.Squeeze the left and right paper guide levers and adjust the guides to match the size
of your paper.
Xerox® 6279® Wide Format Solution1-28
Printer User Guide
Product Overview
Downloaded From ManualsPrinter.com Manuals 

4.Squeeze the rear Paper Guide Lever and adjust it to match the size of your paper.
5.Push the Media Tray in gently until it stops.
1-29Xerox® 6279® Wide Format Solution
Printer User Guide
Product Overview
Downloaded From ManualsPrinter.com Manuals 

NOTE
When printing on cut sheet media, you may load the media in Media Trays 3 or
4 or in the Manual Feed-in Shelf (Bypass).
TIP
Remember that any time you change the size of the paper in a Media Tray or
Drawer, you have to update the Media Source located at
Machine Info > Media Status and Setup on the Touch Screen. Refer to the
Chapter 4, Machine Information Media Status and Setup  section.
Xerox® 6279® Wide Format Solution1-30
Printer User Guide
Product Overview
Downloaded From ManualsPrinter.com Manuals 

2
Job Information
All print and copy jobs are placed in the Job Information queue on the User Interface.
Print jobs are jobs sent to the Xerox Wide Format System from either a remote client
workstation using Web Printer Management Tool or a network Printer Driver.
All Tab
The contents of this tab is a list of all jobs in their various stages of completion. Jobs are
displayed whether sent via Web Printer Management Tool or scanned at the printer.
Active Tab
Jobs that are in progress are shown in the...

Jobs in the Active queue can be placed on hold by selecting them and choosing
Hold Selected.
Jobs can be cancelled from this queue and will remain only on the All tab. This is done
by selecting the job and choosing Cancel Selected. More information can be seen for
any given job by selecting Details.
NOTE
If Immediate Image Overwrite is enabled, there is no Hold function available.
Held Tab
The Hold Queue feature can be used to manage your job workflow by:
•scheduling jobs for printing at a specific time...

5.Select Save.
6.Submit the print job.
7.Locate the job in the Hold queue from Job Information on the UI or Print Queue on
Web Printer Management Tool.
Job Reprint
Completed copy and print jobs are available for reprint if the Administrator has enabled
the Job Reprint feature. The Job Reprint feature is Disabled as the default.The
enable/disable option is controlled in Machine Info > Administration > General
Administration > Configure Job Reprint.
Reprinting jobs is also available on the Web Printer...

Edit Job Settings
Reduce/Enlarge
The Reduction/Enlarge feature has variable options for scaling the images being copied.
The feature provides the ability to customize the preset reduction/enlargement settings
beyond the basics discussed here. The factory default setting is 100%.
The reduction and enlargement features available are:
•Scale Factor: The Scale Factor from 25% to 400% is set by pressing the increase
and decrease arrows in single increments. The numbers pause at standard reduction
and...