Vodavi Starplus Sts Station User Guide

48 Flexible Button Programming
Flexible Button Programming
To program a flexible button (to use feature codes):
1. Press SPEED twice.
2. Press the button to be programmed (must be programmed 
in database as a flexible button).
3. Dial the desired code. A confirmation tone will sound. (Refer 
to the “Default Numbering Plan” on page 96, and the feature’s 
description for any additional digits to enter). 
4. Press the ON/OFF button.
To program a flexible button (to use speed bin dialing):
1. Press SPEED...

Group Listening 49
Group Listening
All digital key stations have a built-in speakerphone. You can 
use the speaker to monitor a call while using the handset to 
consult with the outside party. This enables other people in the 
room to listen to both parties in the conversation.
To activate Group Listening:
While conversing on the handset, press the ON/OFF button.
Both parties of the conversation can then be heard on the 
digital stations speaker. The speakerphone microphone is 
muted while the handset is...

50 Headset Mode
The LED will light steady.
To deactivate Headset Mode:
Dial [634] on the dial pad,
-or-
Press the preprogrammed HEADSET MODE button.
-or-
Use the Soft Key’s HEADSET option when in an idle 
condition.
The LED will extinguish.

SINGLE LINE TELEPHONE
Not applicable
While Headset mode is active, the ON/OFF button 
activates the headset and disables speakerphone and 
intercom call announce operation at your station.
To install the headset, see the Installation Manual.
Station must be...

Intercom 51
Intercom
Using an Intercom Button 
To program a Flexible Button as an Intercom Button:
1. Press the SPEED button twice.
2. Press the desired flexible button to program.
3. Dial [645] on the dial pad. A confirmation tone will sound. If 
an error was made during entry, an error tone will sound.
When intercom call rings a busy station (w/intercom btn):
1. The calling station receives ringback tone instead of busy 
tone. The called station hears muted or reminder ring and 
their intercom button...

52 Intercom
Answering an Intercom Call
Depending on the position of your intercom button signal 
switch, answer the intercom call as indicated:
H Mode (No LED) Handsfree Mode -- You will hear three bursts 
of tone and an announcement.
Reply handsfree or lift handset for privacy.
P Mode (LED Flashing) Privacy Mode -- You will hear three 
bursts of tone and a one-way announcement. The calling party 
cannot hear conversations in progress.
Lift handset or press ON/OFF to answer.
-or-
Position the H-T-P...

Intercom 53
Intercom Calls
To place an Intercom Call:
1. Press the DSS button of the party to be called (if 
programmed at your phone),
-or-
Dial the extension number.
(You will hear ringing if the called station is in the T mode; 
or three bursts of tone if called station is in H or P mode.)
2. Lift the handset or use the speakerphone after the tone 
bursts stop.
3. Hang up to end the call.
To answer an Intercom Call:
In the T mode (LED On), you will hear repeated bursts of 
intercom tone ringing and...

54 Keyset Mode

SINGLE LINE TELEPHONE
To place an intercom call:
1. Lift the handset.
2. Dial the intercom number. You will hear ringing if the called 
station is in the “T” answering mode or two bursts of tone if 
the called station is in the “H” or “P” modes.
3. Hang up to end the call.
To answer an intercom call:
Lift the handset,
-or-
If your SLT is equipped with a speakerphone, press the 
Speaker button to converse in a handsfree mode.
Keyset Mode
This feature allows you to determine the mode and...

Last Number Redial 55
At an idle station:
1. Dial the Keyset Mode code [648] on the dial pad,
-or-
Press the preprogrammed KEYSET MODE button, the 
following displays:
2. Press [

] to scroll through the keyset modes.
3. Press [#] to scroll through the baud rates.
4. Press the HOLD button to save the desired entries.

SINGLE LINE TELEPHONE
Not applicable
Last Number Redial
The Last Number Redial (LNR) feature permits the automatic 
redialing of the last telephone number dialed on an outside 
line. Up to...

56 LCR Operation
The system automatically selects the original line used to place 
the call and redials the last number dialed.

If that line is busy, the system will select another line 
from the same group and redial the number.

If no lines are available in the same group, you will 
receive a busy tone and can queue for a line.

If you preselect a line before activating LNR, the 
preselection will override the line used originally.

SINGLE LINE TELEPHONE
Not applicable
LCR Operation
To place an...

Loop Key 57
CO Line Queue Cancel
To cancel a Call Back Request:
1. Dial the CO Line Queue Cancel code [626] on the dial pad.
2. Replace the handset or press the ON/OFF button.
Loop Key
A station not having a direct appearance for a CO line will 
receive incoming CO calls and transferred CO calls under the 
LOOP button. Only one call at a time can be connected to a 
keyset on the LOOP button.
To make a Loop button:
1. Press the SPEED button twice.
2. Press the desired flexible button.
3. Dial [89].
4....