Vodavi Starplus Dhs Installation Manual

8. Dial the feature code. 
9. Press “8ave”. 
To Erase the Contents of a Programmable Feature Button: 
n Press “save” instead of dialing a code 
Notes: 
. 
a. If you dial an invalid code you will hear error tone and an Executive Key Telephone display will show 
“CODE UNAVAILABLE”. 
b. In some cases a user may program a feature button for a specific CO line although access is restricted 
to that line via database programming. In this situation, the telephone is still governed by database 
pro,qamming and...

4.4.61 Flexible Ring Assignment 
- 
4.4.61.1 Description: 
Any station can be programmed to ring for any or all incoming CO lines. The Ring Assignment will not 
establish ringing at any station that does not also have the Receive Assignment enabled for the associated 
incoming CO line. In this situation, the CO line appearance would provide a visual indication only, with no 
method to answer the incoming call by Direct Line Button Access. A designated Night Service station will 
receive audible ringing...

4.4.63 Forced Tone R@.,&&$?j 
4.4.63.1 Default Setting: N/A 
4.4.63.2 Related Feature: 
Dial Intercom 
Intercom Signal Mode Selection 
4.4.63.3 Related Programming: 
None 
4.4.63.4 Description: 
In certain environments where background noise is predominant or where speaker volume has been 
minimized, a station in Voice Announce mode may not hear your voice when you place an intercom call. 
This situation may be averted by using the Forced Tone Ringing feature. After connection to a Voice 
Announce...

Ifthe SPKR button is pressed while the telephone is idle, the headset is turned on. When the z button 
is pressed again, the speakerphone mode is activated. At any time during any of these modes the handset 
may be lifted to disengage the headset or speakerphone mode. 
4.4.64.5 Operation: 
4.4.64.5.1 To Turn on the Headset: 
FEAT 
1. press B - 
ip$ gy& 
; ,.. “

d. -Other features like background music and muted ring ebntinue to operate in the same manner while 
you are off-hook. 
e. Non-amplified headsets may be powered directly corn the key telephone.. In most cases this interf&e 
permits the key telephone to control the Volume Up/Down and Mute features. Some headsets may 
require the use of the headset adapter keys to adjust the volume, mute and other headset dictions. 
f. Pressing F%&% will disconnect calls when the Headset mode is active. 
4.4.65 Hold...

4.4.66.4 Description: 
Holding Call Answer allows a user to place and retrieve calls on and off of hold by simply pressing the 
HOLD button. When multiple calls are holding at the station, Holding Call Answer will access the CO line 
that has been holding for the longest period of time while placing the current call on hold. Holding Call 
Answer works for all CO lines regardless of the station CO line button programming. 
4.4.66.5 Operation: 
1. Press e . A currently connected call will be placed on...

4.4.68.4 Description: ‘L 
You may place any CO line on System Hold by one button operation of g. When you place a line on 
System Hold, the green lamp for that line will flash at the I-Hold rate. This system-hold line will flash the 
red lamp at all other stations. 
Notes: 
a. If you have Auto Hold Allow enabled a line will be placed on system hold automatically whenever you 
switch from one CO line to another or when you press a DSS button. 
b. Calls placed on Exclusive (private) Hold which have...

4.4.70.2 Related Features: 
Attendant Administration 
Station and System Alarm 
Day/Night Service Mode 
4.4.70.3 Related Programming: 
RESOURCE -ATTENDANT 
RESOURCE - NITE START 
RESOURCE - NITE END 
RESOURCE - SYSTEMALARM 
RESOURCE - SYSTEM TIME 
RESOURCE - HOUR MODE 
Note: When programming related features, military 24 hour time is referenced. 
4.4.71 I-Hold Indication 
4.4.71.1 Default Setting: N/A 
4.4.71.2 Description: 
I-Hold Indication allows you to easily distinguish between a call you placed on...

4.4.74 FEAT @@ 
Last Number Redid .~ZZXQEB s%$ ‘_ 
j.= 
4.4.74.1 Default Setting: Empty 
4.4.74.2 Related Features: 
Automatic Busy Radial 
4.4.74.3 Related Programming: 
RESOURCE - DL4L TONE DET. 
RESOURCE - DL.4L WAIT TIME 
4.4.74.4 Description: 
The Last Number Redial (LNR) feature automatically dials the last number dialed from your telephone. 
LNR will repeat a hook-flash in the same sequence as it was frost dialed. If a speed dial number was first 
dialed, LNR will dial the speed dial number and...

4.4.75 Letter Scheme 
4.4.75.1 Description: 
Station User Names (programmed into the customer database) 
may be enhanced for special requirements using the choices 
available in the Letter Schemes. The end user may select from six 
different lettering schemes that can be programmed for use at any 
one installation. While User Names are being entered (in 
database programming) and while the user is editing an Outgoing 
Message, the chosen Letter Scheme characters will be accessible 
with successive...