Vodavi Starplus Dhs Installation Manual

4.4.44 Direct Station Selection/Busy Lamp Field” 
4.4.44.1 Default Setting: N/A 
4.4.44.2 Related Feature: 
Call Transfer 
Programmable Feature Buttons 
4.4.44.3 Related Programming: 
None 
4.4.44.4 Description: 
Any feature button may be programmed as a combination Direct Station Selection (DSS) and Busy Lamp 
Field (BLF) button. The DSS/BLF button allows you to call a specific station with the touch of one button. 
This same button will light whenever the associated station is busy (off hook) or in the...

4.4.46.1 Default Setting: Disabled 
4.4.46.2 Related Feature: 
Call Forward 
Call Wait 
Dial Intercom 
DND Override 
Forced Intercom Call Forward 
4.4.46.3 Related Programming: 
None 
4.4.46.4 Description: 
DND allows you to temporarily block and discontinue ringing from incoming CO calls and intercom calls. 
You can activate DND while your telephone is idle or busy. Some stations with higher Class Of Service 
may override a station’s DND condition. 
When you have activated DND you will hear special...

4.4.47.4 Description: [Executive Model only] . . 
If you have an Executive Telephone you may override a station in DND if your Class Of Service is 
higher. 
When you override a station in DND that station will hear tone ringing. -. 
4.4.47.5 Operation: 
Let’s assume Station 16 is in DND: 
1. Call Station 16. You will hear DND tone and your display will show: 
: 
The Override option is displayed only if your COS is higher than Station 16’s COS. 
3 
-. Press “override”. If Station 16 is idle your display...

changes to: 
then back to idle. 
Notes: 
a. 
The time limit of Drop Time-out is closely associated with Warning Tone Time programming. If the 
station’s Warning Tone Time is set for 5 minutes and the Drop Time-out feature is enabled, after 5 
minutes have expired, the outgoing CO line call in progress will be released automatically. A double 
beep is also heard. 
b. If Drop Time-out is enabled, only outgoing CO line calls at that station are affected. 
C. At default no Drop Time-out is enabled. 
4.4.49...

4.4.50.3 Related Programming: 
STATION - DAYmITE COS 
RESOURCE-ATTENDANT 
RESTRICTION - CO LN CALL DISCR 
4.4.50.4 Operation: 
See 
System Speed Dial 
Note: At default all stations have COS 0 and may access the Emergency System Speed Bins. 
4.4.51 End-To-End Signaling 
4.4.51.1 Description: 
This feature allows digital key telephone stations to generate m-band DTMF tones on ICM calls to an on- 
site voice mail system. DTMF digits will only be sent to the SLT port when connected to a Z-Port SLT...

a. The Option Module is required for ECF operation. 
b. The activation time is programmable (“Never”, “Day”, “Night” or “Always”). 
C. The CO Line-to-CO Line Conference time is programmable( I,& 3,5, 10, and 15 minutes). 
d. The default conversation time is 1 minute. 
e. The system maintains the forwarded connection until the “conversation time” expires or the forwarded 
f. 
The System CO Line-to-CO Line Conference does not have to be enabled in the Database 
Pl-0gJ-WIVhg. 
g 
C. ECF is greatly enhanced...

Message Waiting Delete 
(“Sn ” = station number where the message 
was left.) 
Premises Message Delete 
4.4.56 Flash cirM $j&$ 
4.4.56.1 Default Setting: 700 ms 
4.4.56.2 Related Feature: 
Speed Dial (System and Station) 
Last Number Redial 
Programmable Feature Buttons 
4.4.56.3 Related Programming: 
CO LJNE - CO LINE TYPE 
CALL HANDLING - FLASH TIME 
CALL HANDLING - PBX CODE 
4.4.56.4 Description: 
When Flash is accessed the system will generate a timed, open loop flash condition on any CO line. The...

4.4.57 Flexible Button Inquiry 
4.4.57.1 Default Setting: N/A 
4.4.57.2 Related Feature: 
Flexible Button Progrtlmming 
4.4.57.3 Related Programming: 
None 
4.4.57.4 Description: [Executive Model only] 
You may review the programming for flexible buttons at an idle Executive Telephone. In order to review 
the pro-mmming you must dial the Flexible Button Programming mode. 
4.4.57.5 Operation: 
FEAT 1. press :;; ;.M:: 
4.4.58.1 Default Setting: See key map at the beginning of this guide. 
4.4.58.2 Related...

All system feature codes may be stored on the Programmable Feature Buttons for one-button operation. 
Certain programmed feature buttons will light when activated (DND, Call Forward, DSVBLF, etc.), while 
others such as Call Pick-Up, Background Music, Last Number Redial, do not. 
Features are separated into three distinct categories for programming on a button: CO line, station, or 
feature. Refer to Appendix A for a listing of feature codes. 
4.4.58.5 Programming: Basic and Enhanced Telephones 
FEAT c....

3. Press a Programmable Feature Button. The current contents of that button is displayed. For this example. let’s 
use button 20. 
4. Press “show”. The name of the current feature stored is displayed. 
5. Press “chg II. The display shows the following: 
Three feature button categories are available for feature button programming; “co In” (CO lines). “sta‘* (station) 
and “feat” (feature). 
To Program a CO Line: 
6. Press “co In”. 
7. Dial the CO line number. Refer to the CO Line Code table above. 
An...