ViewSonic Pjl6243 Projector User Manual

ENGLISH
ViewSonic PJL624325
25
 
E-mail setting
This projector has an E-mail function which can send an alert message 
to users or an administrator if it detects an abnormality on the projector 
or run out of the life span of the lamp. Click E-mail Setting on the main 
menu and follow the below steps.
E-mail setting
Item .................................Description
SMTP server ........................... Enter server name or IP address of the SMTP server. (up to 60 characters)SMTP server port...

ViewSonic PJL624326
26
Chapter 3 Basic Setting and Operation
2  Registering and deleting E-mail addresses
Enter the e-mail address onto "Add e-mail 
address" and click Set button. 
To check the registered addresses, click 
Check/Delete sub menu tab. The address-
es are listed as the figure on the right.
* Up to 10 E-mail addresses can be registered.
To delete the registered addresses, check the 
address you want to delete and click Delete 
button.
Check / Delete
*  If the projector sends an alert...

ENGLISH
ViewSonic PJL624327
27
 
E-mail setting
*		"When PJ lamp is off " signifies the lamp goes out without user operation. "When PJ is turned into Standby  in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the top control or the remote control.
*	Up to 99,999 hours can be set for use time.
Option5  Option selection for sending alert mail
Click Option sub menu tab. Check the con-...

ViewSonic PJL624328
28
Chapter 3 Basic Setting and Operation
* When PJ lamp replacement time is reached:
*  Replace it with a new lamp immediately and reset the lamp counter. If the projector is used without resetting the lamp counter, the alert mail is sent to users in every power-on of the projector. This alert mail will not be sent when unchecking the mail sending condi-tion "When PJ lamp replacement time is reached".
TITLE: Message from projectorProjector Model Name: model nameTCP/IP:...

ENGLISH
ViewSonic PJL624329
29
 
SNMP setting
This projector provides a SNMP (Simple Network Management Protocol) 
agent function. The SNMP consists of a manager and agents. The group 
which communicates information each other with SNMP is called 
"Community". There are two access modes in a community, Refer (read only) and Set (read- 
write). This projector allows to use Refer (read only) only. The SNMP message informs the pro-
jector status called "Trap" to an administrator. Click SNMP...

ViewSonic PJL624330
30
Chapter 3 Basic Setting and Operation
Check and delete the trap address
Checking the registered trap address and 
deleting the address.
To delete the address, tick check box in front 
of the IP address and click Delete button.
* Up to 10 trap addresses can be registered.
Trap check/delete
Trap option
Trap option setting
Tick check boxes in front of the condition item 
to send the trap. 
*  Click Set button if you tick or un-tick the check box on a page.
*		"When PJ lamp is off...

ENGLISH
ViewSonic PJL624331
31
ENGLISH
ViewSonic PJL624331
31
Chapter 4 
 Controlling the Projector
4
Describes controlling and setting of the projector by using the web 
browser.     

ViewSonic PJL624332
32
Chapter 4 Controlling the Projector
Power control and status check
 
Click Power & Status on the main menu. The control page will be dis-
played.
By clicking ON or Standby button on the page, the power of the projector can be con-
trolled. 
Item    Description
PJ status Power  ......................... 
Displays the status of the lamp. (ON, OFF, On starting up, On cooling down, Service in need) Status .......................... 
Displays the status of the projector's power....

ENGLISH
ViewSonic PJL624333
33
 
About projector condition
Status Description
Normal ...............................................................Projector is operating normally.Power management in operation ...........Power management is operatingLamp failure ...................................................Lamp failure is occurringAbnormal Temperature .........................The temperature of the projector became too highStandby after Abnormal Temp. ........ 
Projector detects abnormal temp. and...

ViewSonic PJL624334
34
Chapter 4 Controlling the Projector
Control
Click Control on the main menu. The setting method differs depending 
on the contents of the page. Click on the page number to change pages 
and select desired setting items.
*  
Please see the owner's manual of the projector to have the further information 
of each control item. 
 *   The control page displays valid control items depending on the selected input mode, signal or  functions of the projector you use, therefore, there may...