ViewSonic Pjl6233 Projector User Manual

							
Chapter 4 Controlling the Projector
Control
Click Control on the main menu. The setting method differs depending 
on the contents of the page. Click on the page number to change pages 
and select desired setting items.

Please see the owner's manual of the projector to have the further information of 
each control item. 

The control page displays valid control items depending on the selected input mode, signal 
or  functions of the projector you use, therefore, there may be different controls between the 
described items and actual control items on the page display. For further information , refer to the 
projector's owner's manual.

When the projector is in standby, all the controlling items are inactive.
Input
This function is to select the input mode and source mode of the projector.  Click Set but-
ton after selecting the input and source mode.
Item Description
Input......................... Selects input mode of the projector. 
Source..................... Selects signal source of the input. 
Computer1 :  RGB
  Component
  RGB(Scart)
  S-video
Computer2 : RGB
Video 
						

							ENGLISH

System
This function is to select the system of signal 
input to the projector. The available system 
mode are listed on the pull-down menu but-
ton according to the input signal. Select a 
system and then click Set button.
Control
If the mode (Mode1 to Mode10) which is stored in the item "PC Adjustment" ( p.38) is available, 
they are also listed together with the above mode.
Available selection at the RGB input
Item Description
XGA1........................ It automatically switches to the proper computer 
system of the input signal.
* The computer system modes ( VGA, SVGA, XGA. 
SXGA, UXGA, WXGA...) which meet the input sig-
nal are listed.
Available selection at the Video/S-video/Scart input
Item Description
AUTO........................ It automatically switches to the proper color sys-
tem of the input signal.
* The selectable color systems are PAL, SECAM, 
NTSC, NTSC4.43, PAL-M and PAL-N.
* AUTO is fixed at the Scart input.
Available selection at the Component input
Item Description
AUTO........................ It automatically switches to the proper scanning 
system of the input signal.
* The selectable scanning systems are 480i, 576i, 
480p, 576p, 720p, 1035i and 1080i. 
						

							
Chapter 4 Controlling the Projector
Sound 
This function is to adjust the sound of the 
projector.  The values in the text box repre-
sent the current control value or status.
Item Description
Volume...................
Adjusts the sound volume from the speaker. (0 ~ 31)Mute......................... Suppresses the sound. (ON, OFF) 
						

							ENGLISH

Item Description
Contrast.............................. Adjusts picture con-
trast (0~ 63)
Brightness......................... Adjusts picture bright-
ness (0~ 63)
Color...................................... Adjusts picture color 
saturation (0~ 63)
Tint......................................... Adjusts picture hue 
(0~ 63)
Color temp........................
Sets a color temperature 
mode. (High, Mid, Low, 
XLow, User)
White balance
Red, Green, Blue..... Adjusts each white 
balance respectively. 
(0~ 63)
* When changing the value of the 
white balance, the color temp. 
indicates "User".
Sharpness................................ Adjusts picture 
sharpness. (0~ 15)
Gamma..........................................Adjusts brightness of darker part of the picture. (0~ 15)Noise reduction................Switches noise reduction mode (OFF, L1, L2)Progressive............................Switches progressive mode (OFF, L1, L2, Film)
Reset............................................ Resets the Image adjustment to previous levels.
Store............................................ Stores the Image adjustment values. Select an item [Image1 - Image4] from 
the pull-down menu and click Store button.
Load image mode............. Loads the Image mode. Select an image mode from the pull-down menu 
and click Load button. There may not be available mode depending on the 
input mode as shown in the table left.
Image  adjustment
This function is to adjust the projected picture image and save the image mode. To store 
the adjusted value, click Store button, and to load the adjusted value, click Load button.
Input sourceImage modeVideo Computer
Dynamic 
Standard
Cinema*
Real *
Blackboard(Green) 
Colorboard
Image1 - 4 
The mark "" means that the available image mode in the 
selected input source. The error message appears when 
selecting the disabled image mode indicated with "*".
Control 
						

							
Chapter 4 Controlling the Projector
PC adjustment
Click PC Adj. on the main menu. This function is to adjust the signal from 
the computer connected to the projector to obtain the proper picture 
image on the screen. 
Item Description
Current mode......Displays a current mode like VGA, SVGA, XGA. SXGA, UXGA, WXGA, etc. or Mode1 - Mode10 
which are the customized mode created by using the "Mode Store" function described 
below.
Auto PC adj.......... Performs automatic adjustment.
Fine sync .............. Performs Fine Sync adjustment. (0 ~ 31)
Total dots.............. Adjust the number of total dots in the horizontal period.
Clamp...................... Adjusts the phase of the clamp.
Display area 
Horizontal.......... Adjusts the image area horizontally.
Vertical.............. Adjusts the image area vertically.
Position
Horizontal....... Adjusts the horizontal position of the screen.
Vertical.............. Adjusts the vertical position of the screen.
Reset......................... Resets the PC adjustments to the previous levels.
Mode Store.......... Stores the PC adjustment values. Select a mode no. [Mode1 - Mode10] from the 
pull-down menu.
Mode Free............ Clear the PC adjustment values. Select a mode no.  [Mode1 - Mode10] from the pull-
down menu. 
						

							ENGLISH

Setting up the projector
Click Setting on the main menu. This function is to set up the projector. 
Select the sub menu [Screen setting] or [Setting] and then set up each set-
ting.
Setting up the projector
Item Description
Screen..................... Switches the screen mode. (Normal, True, Wide, Full, Custom) There may not be avail-
able mode depending on the input mode as shown in the table below.
Input sourceScreen modeVideo Computer
Normal
True *
Wide
Full *
Custom
The mark "" means that the available screen mode in 
the selected input source system. The error message 
appears when selecting the disabled screen mode indi-
cated with "*".
Screen setting 
This function is to adjust the screen mode of 
the projector.  The values in the text box rep-
resent the current screen status. 
						

							
Chapter 4 Controlling the Projector
Item Description
Ceiling..................... Sets the image top/bottom and left/
right reversed. (ON, OFF)
Rear........................... Sets the image left/right reversed. (ON, 
OFF)
Terminal................. Sets the COMPUTER IN 2/MONITOR 
OUT terminal. (Computer2, Monitor 
out)
Power 
management..... Sets into the selected power manage-
ment mode (Ready, Shutdown, OFF) if 
the input signal is interrupted and no control key is pressed for the specified period 
of time.
*The specified time can be set 1 t
o 30 min.Direct on................ Sets the power-on mode when the AC cord is connected to the outlet. (ON, OFF)
Lamp control...... Selects lamp control mode. (High, Normal, Eco) 
Setting 1
Setting 2
Item Description
Language.............. Sets the language display of projector's 
on-screen display menu.
Auto setup........... Executes the Auto PC Adj, Input Search 
and Auto keystone function below 
according to the each setting after click-
ing
Start button.
Auto PC Adj. ..... Sets Auto PC Adjustment mode. (ON, 
OFF)
Input search ..... Sets the auto-input signal detection 
mode. (ON1, ON2, OFF) 
Auto keystone ....Sets Auto Keystone mode. (Auto, Manual, OFF)
Background......... Sets the screen background  when no signal input. (Blue, User, Black)
Display.................... Switches on or off the on-screen menu display on the screen. (ON, OFF)
Logo......................... Sets on or off the logo display on the screen during the startup. (OFF, Default, User)  
						

							ENGLISH

Setting up the projector
Item Description
Key lock.................. Sets the prohibition of controls either 
Projector or Remote control. (OFF, 
Projector keys, Remote control)
Fan control
.............Sets the fan control speed. 
OFF Normal mode
ON1 Highland mode 1
ON2 Highland mode 2
Lamp Corres.
Value(h).................. Displays the lamp use time 
(Corresponding value) . Reset the time 
after lamp replacement. Click "Reset", a 
confirmation display appears, and then 
click "OK", the time will be reset. 
Filter counter...... Displays the filter counter. Reset the time 
after filter clean-up. Click "Reset", a confirmation display appears, and then click "OK", 
the time will be reset. 
Filter warning..... Sets the time to indicate the filter warning message on the screen. (OFF, 100H, 200H, 
300H)
Factory default...Sets all of the projector control items to the factory default setting except the fol-
lowing items.
User Logo, Logo PIN code lock, PIN code lock, Lamp Corres. Value, Filter counter, PJ 
time
* This function is effective for all the Network settings.
No show................. Sets the black out image temporarily. (ON, OFF)
Freeze...................... Sets the image to freeze mode.  (ON, OFF)
Closed caption.. Sets the closed caption function. 
Closed caption... Sets the closed caption mode. (OFF, CC1, CC2, CC3, CC4)
Color ..................... Sets the color of the contents. (Color, White) 
Setting 3 
						

							
Chapter 4 Controlling the Projector
Information
This page is to display the basic information of the projector status. Click 
Information on the main menu.
Items Description
InputDisplays selected input and source.
SystemDisplays selected signal system.
SignalInput signal status (Yes, No)
ScreenDisplays screen mode.
Lamp status   Displays lamp status with an icon. Refer to the table as shown below.
SecurityDisplays the security (PIN code lock) status (Yes, No)PJ time(h)Displays the accumulated use time of the projector.Lamp Corres. Value(h)   Displays the use time (Corresponding value) of the lamp.
Filter time(h)Displays the accumulated use time of the filter.
Click this button to 
update the information.
Indication of the lamp status
Icon display/backgroundStatus
White/BlueLamp on (Normal)
White/RedLamp on (Lamp is being used over a specified use time, replace lamp 
immediately)
Gray/BlueLamp off (Normal)
Gray/RedLamp off (Lamp is being used over a specified use time, replace lamp 
immediately)
Red/Blue with XLamp failure (Lamp failure, check lamp condition)
Red/Red with XLamp failure (Lamp failure and lamp is being used over a specified use 
time, replace lamp immediately) 
						

							ENGLISH

ENGLISH
ViewSonic 3-/3-/

Chapter 5
 Appendix 5
Connection examples
Use of telnet
Web browser setting
Q & A