ViewSonic Pjl6233 Projector User Manual

							
Chapter 2 Setup Procedures
The Network PIN code is to restrict the access to the projector through the network.
After setting the Network PIN code, you need to enter it to operate the projector via the 
networks.
Network PIN code
Network information
1. Select "Network PIN code" in the Network menu, and press SELECT button. 
The Network PIN code screen will appear.
2. Set the Network PIN code.
Set the figures with the Point ed buttons and move to the next items with the Point 
buttons. Select “Set” and press SELECT button to set. To cancel the preset Network PIN 
code, select “Cancel”. When you do not want to set the Network PIN code, set "0000".
It is recommended to set the Network PIN code if you use the projector via the networks.  
The Network PIN code can be set also through the networks.  See “3. Basic setting and 
operation” “Initial setting” “Network PIN code setting” (p.23).
Select "Network information" in the Network menu and press Point  or SELECT button 
to show LAN setting environment of the currently selected projector. (The description 
below is an example and different from what will be shown.)
Network PIN code
Network PIN code screen
* The numerical value is a setting example. 
						

							ENGLISH
15
Network factory default
Network factory default
1. Select “Network factory default” in the Network menu and press SELECT button.
2. A confirmation box appears and select "Yes" and then press SELECT button.
3. Another confirmation box appears and select "Yes" and then press SELECT button.
4. All the wired LAN settings will go back to the factory default settings. For details, refer to 
“Wired LAN factory default settings” (p.16). 
						

							
Chapter 2 Setup Procedures
Wired LAN factory default settings
ParameterSELECTED LAN
LAN 1 LAN 2 LAN 3
DHCP OFF ON OFF
IP ADDRESS 169.254.100.100 192.168.100.100 192.168.100.100
SUBNET MASK 255.255.0.0 255.255.255.0 255.255.255.0
GATEWAY ADDRESS 255.255.255.255 255.255.255.255 255.255.255.255
DNS ADDRESS 255.255.255.255 255.255.255.255 255.255.255.255 
						

							ENGLISH
17
ENGLISH
ViewSonic 3-/3-/17
17
Chapter 3
 Basic Setting and Operation3
Describes basic operations and settings for controlling the projec-
tor by using the web browser. It is required that computer and 
projector is connected to the network and the network address is 
properly configured. 
						

							
Chapter 3 Basic Setting and Operation
Login the setting page of the projector
[1] Enter the IP address
Launch the web browser installed in your 
computer, enter the IP address into the 
"Address" on the browser and then press 
"Enter" key.
Enter the address that you configured in 
item "Network configuration" ( p.12).
[2] Login
If the setting page has set the password, the authentication window will appear. In this 
case type "user" onto the User Name text area and the login Network PIN code onto 
the Password text area and then click OK (Log in) button.
* The entering User Name must be "user" and it can not be changed.
[Note]
When accessing the projector for the first time or the Network 
PIN code "0000" is set, the auto-login will be performed and 
the next main setting page is displayed.
* The numerical value is a setting example. 
						

							ENGLISH

[3] Display of main setting page
The following main set ting page will be displayed according to your display mode 
selection. Perform various kinds of settings through this page. Click on the menus to dis-
play the control and setting pages.
Main setting page in the display
Setting page
Displays the control and 
setting items according to 
the selected menu.Main menu
For selection of  control and 
setting items of the projector. 
Sub menu tab
Switches the sub 
menu tab.
Login the setting page of the projector 
						

							
Chapter 3 Basic Setting and Operation
How to use the setting page
To control and set up the projector, use the setting menus on the web browser. Describes the 
basic operation and procedures commonly used on this manual.
The setting menu appears when 
clicking the sub menu tab. 
* Each item has a valid setting range 
respectively.
Example of the setting page

The value in the text box indicates current value.

Each item has a valid setting range. The setting value exceeding this becomes invalid. Some control 
items can not be used depending on the selecting input mode or functions of the projector you 
use. In this case, the values of those items are indicated with "---".
Text box setting
Enter a number or text and then click Set button.
or 
Change a value with 
–or +button.
Pull-down menu setting
Select an item with pull-down menu 
button and then click Set button.
Types of setting 
						

							ENGLISH
21
How to use the setting page
Radio button setting
Select an item by selecting a radio 
button.
Check box setting
Select items by ticking on check 
boxes. 
						

							22
Chapter 3 Basic Setting and Operation
Initial setting
After installing the projector, perform the following basic initial setting.
Click Initial Setting on the main menu to display the initial setting page.
Item Description
Language.............. Switches display language on the setting page. (Japanese, English)
Model name....... Indicates the model name of the projector
Network PIN code......
Sets the Network PIN code to login the setting page (p.23)PJLink....................... Switches PJLink password authentication. (ON, OFF) (p.23)Password............... Password for PJLink function (p.23) 
						

							ENGLISH

Initial setting
Network PIN code setting
This is to set the Network PIN code to restrict 
the access from an unauthorized person 
through the network. 
Enter a 4 - digit number as the Net work PIN 
code onto the text box and click Set button. 
  The projector begins restarting and it takes 
about 10 seconds. Close (Quit) the web 
browser and access to the login page again in 10 seconds. This is to perform the login 
authentication firmly.
The default Network PIN code [0000] means no Network PIN code is set.  

When you connect the projector to the network, it is recommended to set a new Network PIN
code. Only a four-digit number is valid for the Network PIN code.
PJLink and password setting
This is to set the PJLink password authentica-
tion on or off. If set "ON" with the PJLink pull-
down menu, the password must be required. 
Enter a password* onto the text box and click 
Set button. 

1 to 32 alphanumeric characters can be used for the password.
What's PJLink?
The projectors equipped with PJLink function can be used together on the same network, 
regardless of model or brand, for centralized control and monitoring. This standard was 
established by the Japan Business Machine and Information System Industries Association 
(JBMIA). Please visit the Website at http://pjlink.jbmia.or.jp/english/.
PJLink Notice
The projector is compliant with PJLink Standard Class 1 of JBMIA, and it supports all com-
mands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1.
Projector Input PJLink Input Parameter
Computer 2 RGB RGB 1 11
Computer 1 RGB RGB 2 12
Component RGB 3 13
S-video RGB 4 14
RGB (Scart) RGB 5 15
Video Video VIDEO 2 22