Home > Toshiba > Communications System > Toshiba Stratagy 4/6/24 Installation And Maintenance Manual

Toshiba Stratagy 4/6/24 Installation And Maintenance Manual

Here you can view all the pages of manual Toshiba Stratagy 4/6/24 Installation And Maintenance Manual. The Toshiba manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 81

STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 
, 
PARAMETER 
fax-send-speed 
fax-start-char 
fax1 
fax2 
smdi-base-port 
smdi-port 
DESCRIPTION 
Maximum speed that Stratagy will use for sending faxes. Depending upon the 
type and speed of your computer set this appropriately. Normally a value of 3 
works for 386 CPUs at 33 MHz or higher. If you experience data loss on your 
faxes, lower this setting. 
‘: (empty string) as fast as possible 
‘0’: 2400 
‘1’: 4800 
‘3’: 9600 
Possible...

Page 82

STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 
PARAMETER 
smdi-pretimeout 
DESCRIPTION 
Maximum number of seconds that an SMDI packet can PRECEED the forwarded 
call. 
smdi-type 
box-grt Possible values: 5 - 20 (seconds) 
Default: 50 Stratagy 6 and 24 only. 
Protocol Stratagy uses when using RS-232 data integration (outband integration). 
‘smdi’: standard SMDI integration 
‘s75’: System 75 integration 
Possible values: ‘SMDI’, ‘~75’ The single quotes are required. 
Default: ‘smdi’...

Page 83

STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 
‘ 
PARAMETER 
did-dtmf 
DESCRIPTION 
How DID digits are passed to Stratagy. 
TRUE: Stratagy expects the DID digits as DTMF. 
FALSE: Stratagy expects the digits as loop pulse. 
Possible values: true, false 
did-mode 
ring-mode 
H-mode Default: comment line (#set did-dtmf true) Stratagy 6 and 24 only. 
If this option is activated by removing the starting # character, it will define the 
type of line connected to Stratagy. 
TRUE: Stratagy...

Page 84

STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 
5 INSTALL FROM A: DRIVE 
Use this function to install Stratagy software from 
diskettes using the Stratagy floppy A: drive. This is 
required when upgrading a Stratagy 4 system to a 
Stratagy 6 system. It may also be necessary to re-install 
Stratagy System or Prompt software from floppy 
diskettes. 
IMPORTANT NOTE: 
Before installing or re-installing Stratagy 
System software, ensure you have a current 
backup of system data. We...

Page 85

STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL 
SEPTEMBER 1994 
Otherwise, press Esc again to reboot Stratagy and 
return to the Main Menu for call processing or Stratagy 
programming. 
7 TOSHIBA SWITCH 
INTEGRATION 
Use this function to change the Toshiba Plug and Play 
capability that has been pre-installed with each Stratagy 
system (see “Toshiba Plug and Play”). Selecting an 
option automatically defines the Toshiba telephone 
system dial codes, Toshiba telephone system tone 
patterns, and...

Page 86

STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 
8 OTHER SWITCH 
INTEGRATIONS 
Use this function to initially configure or modify the 
following for non-Toshiba telephone systems: 
n Telephone system dial codes 
n Telephone system tone patterns 
n System integration patterns 
IMPORTANT NOTE: 
Be sure to configure the Strafagy system in 
the above-listed order. 
NOTE: 
We recommend that you use the Stratagy 
Backup Utility initially and periodically to 
preserve system data. Before...

Page 87

‘ 
STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 
1. Telephone System Dial Codes 
# Dial code to put a caller on transfer hold : F- 
# Dial code to use when there is no transfer dialtone: F- 
# Dial code to return to caller after Ring No Answer : F- 
# Dial code to return to caller when there is a Busy : F- 
# Dial code to use after a call screening reject : F- 
# Dial code to connect the caller to the extension :H 
# Number of seconds to wait for dialtone detection :4 
# Number of...

Page 88

STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 
PARAMETER 
DESCRIPTION 
# DIAL CODE TO PUT A CALLER ON TRANSFER HOLD: 
Before Stratagy attempts to transfer a caller to an extension, the code Stratagy sends the telephone 
system to put the current call on “transfer hold” and send the transfer (or intercom) dial tone. 
Typical value: F- (flash-hook) 
# DIAL CODE TO USE WHEN THERE IS NO TRANSFER DIALTONE: 
If Stratagy is configured to verify that transfer dial tone exists before...

Page 89

, STRATAGY 4/6/24 
INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 
PARAMETER DESCRIPTION 
#WHICH DTMF TONE TO LISTEN TO FOR ANSWER DETECTION: 
Some telephone systems play a specific DTMF tone during a call transfer when the called extension 
answers. This allows for faster answer detection and call processing. If your telephone system supports 
this feature, enter the DTMF tone. 
Typical value: a 
#WHICH DTMF TONE TO LISTEN TO FOR HANG UP DETECTION: 
Some telephone systems play a specific DTMF tone...

Page 90

STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 
8.2 DEFINING TELEPHONE SYSTEM TONE 
PATTERNS 
Use this option to define for Stratagy the actual 
telephone system tone patterns it must recognize when 
performing supervised call transfers. 
To define the tone patterns the Stratagy system uses a 
utility called GetTones. This program enables Stratagy to 
“learn” the tone patterns that define ringing, busy, hang 
up, and reorder. 
NOTE: 
The tone patterns for Toshiba telephone systems...
Start reading Toshiba Stratagy 4/6/24 Installation And Maintenance Manual

Related Manuals for Toshiba Stratagy 4/6/24 Installation And Maintenance Manual

All Toshiba manuals