Home
>
Toshiba
>
Communications System
>
Toshiba Stratagy 4/6/24 Installation And Maintenance Manual
Toshiba Stratagy 4/6/24 Installation And Maintenance Manual
Here you can view all the pages of manual Toshiba Stratagy 4/6/24 Installation And Maintenance Manual. The Toshiba manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 71
‘ STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 PARAMETER hot-box DESCRIPTION If you remove the initial # sign and activate this option, when Stratagy detects a specific tone, Stratagy “jumps” to a specified User ID. Used to handle incoming faxes, detect connections from TDD machines for deaf communication, etc. There are 24 values available. For example: set hot-box 994 sets all 24 to User ID 994 set hot-box 994 1 sets the first hot-box to User ID 994 Possible values:...
Page 72
STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 ‘ PARAMETER n-ochan DESCRIPTION Number of dedicated ports (starting at port 1) to reserve for outbound notify ports. This number must not exceed the total number of available ports. IMPORTANT NOTE: If the value is set to 0, Stratagy will attempt to use the highest numbered IDLE port. The danger of this is that Stratagy may inadvertently begin a notification on a port with an incoming call. Possible values: 0 - 24 (number of...
Page 73
‘ STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 PARAMETER play-skip DESCRIPTION Number of seconds to rewind or skip forward during message playback when a * or # is pressed. Possible values: 1 - 99 (seconds) Default: 5 please-hold Whether or not the system says “Please hold while I try that extension for you” before transferring a caller. TRUE The system plays the above prompt. FALSE The system does not play the above prompt and immediately executes the dl_dtwait string...
Page 74
STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 PARAMETER security-min-length DESCRIPTION Minimum length security code that Stratagy will accept as a new security code when a user attempts to change it from a telephone. Possible values: 1 - 8 Default: 1 short-direct-send What is played when the direct message code (usually 998) is entered followed by the User ID. TRUE: “You entered” and the User ID’s name and extension recording plays. FALSE User ID’s current greeting plays...
Page 75
STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 , PARAMETER tmo-blank DESCRIPTION Total number of minutes Stratagy waits before blanking the Main Menu screen to prevent screen burn-in. NOTE: This option only blanks the screen if the current screen is the Main Menu. Possible values: 0 (disabled), 1 - 99 (minutes) Default: 5 tmo-dtmf Amount of time Stratagy waits to determine that the caller has finished entering DTMF digits (provided that they do not press the #). In units...
Page 76
STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 , PARAMETER tmo-serial tmo-silence DESCRIPTION Maximum number of seconds Stratagy waits for a response when communicating with other peripheral devices through a serial port. Otherwise, Stratagy could potentially wait forever. Possible values: 2 - 99 (seconds) Default: 2 Stratagy 6 and 24 only. Maximum amount of silence time the system waits before deciding to finish a recording and hang up. In seconds. Possible values: 3 - 9...
Page 77
STRATAGY 4/6,‘24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 PARAMETER databitsl databits databits databits parity1 parity2 parity3 parity4 DESCRIPTION Number of data bits for logical serial port 1. Possible values: 7, 8 Default: 8 Number of data bits for logical serial port 2. Possible values: 7, 8 Default: 8 Number of data bits for logical serial pot-l 3. Possible values: 7, 8 Default: 8 Number of data bits for logical serial port 4. Possible values: 7, 8 Default: 8 Parity...
Page 78
STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 PARAMETER serial-port1 DESCRIPTION In order for Stratagy to communicate with peripheral devices connected to COM/RS232 ports, it needs to know which ports are connected. There is a mapping from the port that Stratagy knows to the physical port on the computer. This mapping is defined by this option. To define serial port 1 as active, simply define the COM port where it should be mapped. serial-port2 Example: Set this option to 1...
Page 79
STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 , PARAMETER stopbitsl stopbits stopbits stopbits fax-dl-init fax-flow-control fax-id fax-max-retries DESCRIPTION Number of stop bits to use for logical serial port 1. Possible values: 0, 1, 2 Default: 1 Stratagy 6 and 24 only. Number of stop bits to use for logical serial port 2. Possible values: 0, 1, 2 Default: 1 Stratagy 6 and 24 only. Number of stop bits to use for logical serial port 3. Possible values: 0, 1, 2...
Page 80
, STRATAGY 4/6/24 INSTALLATION AND MAINTENANCE MANUAL SEPTEMBER 1994 PARAMETER fax-receive-reverse DESCRIPTION Setting depends solely on the Class 2 fax/modem used. Controls whether to reverse the fax databits on receive. TRUE Setting for most fax/modems. FALSE Setting for some fax/modems. If the faxes received are reverse (mirror fax-receive-speed fax-requeue-interval fax-reset fax-send-reverse images) from the original, try setting this option to FALSE. Possible values: true, false...