Toshiba Strata Dk14, Dk40i, Dk424 Programming Manual

ISDN
Program *68-1 – Calling Number ID Presentation Parameters
Strata DK Programming 5/997-33
ISDN
Program *68-1 – Calling Number ID Presentation 
Parameters
Processor Type:DK40i, All RCTUs (Release 4.0 or higher)
Program Type:Trunk, PRI and BRI
Initialized Default:all LEDs OFF
Program *68-1 Overview
This program assigns the Number Privacy feature, which allows the caller to prevent the public 
network from delivering the Calling Number to the called party on a per-call basis. The Public 
Switched...

ISDN
Program *68-2 – Outbound CNIS Parameters
7-34Strata DK Programming 5/99
Program *68-2 – Outbound CNIS Parameters
Processor Type:DK40i, All RCTUs (Release 4.0 or higher)
Program Type:Trunk, PRI and BRI
Initialized Default:Blank
Program *68-2 Overview
This program defines the default Calling Party Number (CPN) for the ISDN trunk group used for 
placing a call. The PSTN uses this Calling Party Number for the user provider Caller ID and 
optionally may use it for billing the call.
The number sent is...

ISDN
Program *69-1 – CNIS Presentation Parameters
Strata DK Programming 5/997-35
Program *69-1 – CNIS Presentation Parameters
Processor Type:DK40i, All RCTUs (Release 4.0 or higher)
Program Type:Trunk, PRI and BRI
Initialized Default:none
Program *69-1 Overview
This program defaults all ports to the 00 index, which means that outgoing calls will present the 
Directory Number entered in Program *68-2 as the Calling Number for outbound calls. Each 
station on the Strata DK can send a unique number based on...

ISDN
Program *69-2 – Special Number Assignment
7-36Strata DK Programming 5/99
Program *69-2 – Special Number Assignment
Processor Type:DK40i, All RCTUs (Release 4.0 or higher)
Program Type:Trunk, PRI and BRI
Initialized Default:none
Program *69-2 Overview
This program defines the parameters for the Calling Party Number (CPN) to be presented for a call 
depending upon whether the ISDN trunk group uses DID, private numbers or a default number 
from Program *68-2. Calling Number Presentation for outbound...

Strata DK Programming 5/998-1
E911
E9118
This chapter contains programming record sheets, along with specific instructions for 
programming E911 CAMA trunks.
Enhanced 911 CAMA trunks apply only to the DK424, Release 4.0. The RMCU/RCMS PCBs 
provide up to four CAMA trunk circuits. The RMCU/RCMS eliminates the need for adjunct 
terminal adapter equipment for connecting to E911 CAMA trunks. For more information on 
hardware, refer to the Strata DK Installation and Maintenance Manual.
Operation Overview
The...

E911
SMDR
8-2Strata DK Programming 5/99
©Press DN button and dial 9+911 (with LCR). When the user dials 9, the station will seize LCR 
on its PDN, when the user dials 911, the PDN will drop LCR and the same PDN will connect 
to the CAMA trunk. 911 plus the station’s CESID will be sent out the CAMA trunk. 
©Press INT button and dial 911 (attendant console). When the user dials 911, the INT button 
releases from the internal connection and seizes the CAMA trunk. 911 plus the Attendant 
Console CESID is...

E911
Programming Overview
Strata DK Programming 5/998-3
E911
Notes
lThis record is similar to a Start record except that:
lThe first character “E” indicates “End of Call.”
lCall duration is provided.
lTime of day shows disconnect time.
Figure 8-2 SMDR End of Call
Programming Overview
The basic programming for the E911 CAMA trunks feature is accomplished using Programs *11, 
*12, and *13.  Program *10 is not used for RMCU/RCMS CAMA trunks, it is only used when 
E911 is provided using an adjunct E911...

E911
Program *11-0 – E911/CAMA Trunk Assignments
8-4Strata DK Programming 5/99
Program *11-0 – E911/CAMA Trunk Assignments
Processor Type:All RCTUs (Release 4.0)
Program Type:System
Initialized Default:all LEDs OFF
Program *11-0 Overview
This program enables E911 calls to be analyzed by the system for appropriate handling. The 
following assignments in Program *11-0 must be enabled to allow Enhanced 911 (E911) CAMA 
trunks to operate:
LED 11: CAMA Operation Enabled/Disabled
Led 11 must be turned ON to...

E911
Program *11-0 – E911/CAMA Trunk Assignments
Strata DK Programming 5/998-5
E911
When this feature is used, the station or Attendant console that answers the E911 notification call 
will be connected in a three party conference with the E911 calling telephone and the E911 CAMA 
trunk (E911 dispatch person who answers the 911 call). The CESID information and user name of 
the 911 calling station displays on all Attendant Console monitors and E911 notification telephone 
LCDs when the E911 notification...

E911
Program *11-1 – CAMA Trunk Group Line Assignments
8-6Strata DK Programming 5/99
Program *11-1 – CAMA Trunk Group Line Assignments
Processor Type:All RCTUs (Release 4.0)
Program Type:System
Initialized Default:all LEDs OFF
Program *11-1 Overview
This program assigns lines to CAMA trunk groups. Each RCMU/RMCS line used must be 
assigned to one of the eight CAMA trunk groups using Program *11-1. The RCMU/RMCS system 
line number (not the CAMA trunk number, 1~4) is entered into the appropriate CAMA...