Toshiba Strata Dk14, Dk40i, Dk424 Programming Manual

ISDN
Program *44 – BRI Service Profile Identifier (SPID) Parameters
Strata DK Programming 5/997-13
ISDN
Program *44 – BRI Service Profile Identifier (SPID) 
Parameters
Processor Type:DK40i, All RCTUs (Release 4.0 or higher)
Program Type:Trunk, BRI
Initialized Default:Blank
Program *44 Overview
BRI interfaces generally require entering an Service Profile Identifier (SPID) intialization value to 
activate the interface. This program assigns the initialization interface.
When ISDN service is ordered, a SPID...

ISDN
Program *60 – BRI Line/Station Operation Assignment
7-14Strata DK Programming 5/99
Program *60 – BRI Line/Station Operation Assignment
Processor Type:DK40i, All RCTUs (Release 4.0 or higher)
Program Type:System, BRI
Initialized Default:All LEDs OFF
NotePower must be cycled OFF, then ON before changes take effect.
Program *60 Overview
This program assigns each circuit for CO Line (TE) or ISDN Station (NT) operation. Circuits 1 or 
2 can be used for either CO line or ISDN station operation, while...

ISDN
Program *61 – Analog Trunk Services for ISDN
Strata DK Programming 5/997-15
ISDN
Program *61 – Analog Trunk Services for ISDN
Processor Type:DK40i, All RCTUs (Release 4.0 or higher)
Program Type:Trunk, PRI and BRI
Initialized Default:see below
Program *61 Overview
When analog CO lines use ISDN facilities, each analog CO Line needs to be assigned the type of 
service expected to be used when originating calls. The choices are Speech or 3.1 kHz (used for 
modem and fax connections). Set the...

ISDN
Program *62 – Non-ISDN Station Bearer Service
7-16Strata DK Programming 5/99
Program *62 – Non-ISDN Station Bearer Service
Processor Type:DK40i, All RCTUs (Release 4.0 or higher)
Program Type:System, PRI and BRI
Initialized Default:see below
Program *62 Overview
When Strata DK stations, except ISDN stations, use ISDN facilities, each station needs to be 
assigned the type of service expected to be used. The choices are Speech or 3.1 kHz (used for 
modem and fax connections). Set the transmission...

ISDN
Program *63 – ISDN Dialing Parameters
Strata DK Programming 5/997-17
ISDN
Program *63 – ISDN Dialing Parameters
Processor Type:DK40i, All RCTUs (Release 4.0 or higher)
Program Type:System, PRI and BRI
Initialized Default:4 seconds
Program *63 Overview
This program sets the timer for sending dialed digits if the user does not press the 6WDUW button or 
if the dialed number does not meet the established dialing plan number of digits.
When the sub-address dialing timer is set to 00, subaddress dialing...

ISDN
Program *64-1 – Direct Inward Dialing Parameters
7-18Strata DK Programming 5/99
Program *64-1 – Direct Inward Dialing Parameters
Processor Type:DK40i, All RCTUs (Release 4.0 or higher)
Program Type:Trunk, PRI and BRI
Initialized Default:LED 01 ON for DID or DNIS programming
Program *64-1 Overview
Program *64-1 assigns each ISDN trunk group to use DID/DNIS programming or provide Direct 
in Line (DIL) ringing for incoming calls.




  6SNU
   +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG...

ISDN
Program *64-2 – Number of DID/DNIS Digits for Trunk Groups
Strata DK Programming 5/997-19
ISDN
Program *64-2 – Number of DID/DNIS Digits for Trunk 
Groups
Processor Type:DK40i, All RCTUs (Release 4.0 or higher)
Program Type:System, PRI and BRI
Initialized Default:Blank
Program *64-2 Overview
This program establishes the number of digits to be used for DID or DNIS table interpretation for 
each ISDN trunk group.
The DK424 uses the last two to four digits of the incoming listed directory number (LDN)...

ISDN
Program *65 – ISDN Channel Group Assignment
7-20Strata DK Programming 5/99
Program *65 – ISDN Channel Group Assignment
Processor Type:All RCTUs (Release 4.0 or higher)
Program Type:System, PRI
Initialized Default:All LEDS OFF (see Important! below)
NoteProgram *65 must be assigned before entering Program*66.
Program *65 Overview
This program assigns an ISDN group number and its PRI B-channel members. All B-channels 
assigned to an ISDN channel group must use the same D-channel. The B-channels on the...

ISDN
Program *66-1 – Channel Group Number Parameters
Strata DK Programming 5/997-21
ISDN
Program *66-1 – Channel Group Number Parameters
Processor Type:All RCTUs (Release 4.0 or higher)
Program Type:Trunk, PRI
Initialized Default:Blank
NoteProgram *65 must be assigned before entering Program *66. If Program *65 changes, then 
this program will be affected. Program *66 defaults back to the settings in Program *65.
Program *66-1 Overview
This program assigns PRI ISDN trunk groups to a channel group.
ISDN...

ISDN
Programs *66-2 and *66-4 – Call-by-Call Trunk Group Codes and Network ID
7-22Strata DK Programming 5/99
Programs *66-2 and *66-4 – Call-by-Call Trunk Group 
Codes and Network ID
Processor Type:All RCTUs (Release 4.0 or higher)
Program Type:Trunk, PRI
Initialized Default:Blank
Program *66-2 Overview
The facility code and service parameters will be supplied by the ISDN carrier at the time the ISDN 
lines are ordered. Standard telephone services (POTS) will not have a Facility Code, nor a Service...