Toshiba Strata Dk14, Dk40i, Dk424 Installation And Maintenance Manual

Strata AirLink Systems
BSIA System Installation
Strata DK I&M 5/9916-29
Strata AirLink Systems
Table 16-6 User Settings
LineAmphenol Connector/
PairHandset ID
(1 - 1535)Extension #
(1 - 10 digits)User Name/Comment
(1 - 12 characters)
1 P1, Pair 1
2 P1, Pair 2
3 P1, Pair 3
4 P1, Pair 4
5 P1, Pair 5
6 P1, Pair 6
7 P1, Pair 7
8 P1, Pair 8
9 P1, Pair 9
10 P1, Pair 10
11 P1, Pair 11
12 P1, Pair 12
13 P1, Pair 13
14 P1, Pair 14
15 P1, Pair 15
16 P1, Pair 16
17 P2, Pair 1
18 P2, Pair 2
19 P2, Pair 3
20 P2, Pair...

Strata AirLink Systems
BSIA System Installation
16-30Strata DK I&M 5/99
Table 16-7 Feature Table 
Events 1 - 20
(Use the Commands or Text Displays Listed Below)
Button
Sequence
FLSH
FCN 1
FCN 2
FCN 3
FCN 4
FCN 5
FCN 6
FCN 7
FCN 8
FCN 9
FCN 0
FCN *
FCN #
Text Displays
OK
TRANSFER
V-M AI L
VMS
Clear Display CALL WAIT
CALL BACK
CAMP ON
CONF
E-MAIL
NOT AVAIL
Commands
Echo (digits entered)
Key Pad Pause
User Extension
Hookflash
Oh-hook
Off-hook
Terminate Call
1
Digit 7
Digit 8
Digit 9
Digit 10
Digit *
Digit #...

Strata AirLink Systems
BSIA System Installation
Strata DK I&M 5/9916-31
Strata AirLink Systems
Substep F:  Store the IDs in the Handset
1. Press 
3:5. The handset turns on.
2. Press 
)&1.
3. Press 
t until SYSTEM 
CONFIG.
 
displays
...or 
 + )&1.
4. Press 
)&1.
5. Enter the proper System ID 
(SID).
NoteThe SID must match the data entered in the system 
settings.
6. Press 
&/5to make 
corrections.
7. Press 
t.
8. Enter the handset ID (four 
digits) for the system ID 
entered in Substep 5.
9. Press 
t...

Strata AirLink Systems
BSIA Additional Information
16-32Strata DK I&M 5/99
BSIA Additional Information
The following tables have additional information unique to the BSIA system and cover:
©BSIA (controller) specifications – Table 16-8
©Adapter and BSIA pinouts – Ta b l e s  1 6 - 9 and 16-10
©ALM removal
©Initial configuration change
©Password change
©Base Station additions
©Communication port change
BSIA (Controller) Specifications
Adapter and BSIA Pinouts
Tables 16-9 and 16-10 list the adapter and...

Strata AirLink Systems
BSIA Additional Information
Strata DK I&M 5/9916-33
Strata AirLink Systems
 
ALM Removal
1. Power off the BSIA.
2. Remove the screws securing the cover of the BSIA case.
3. Lift the cover off of the BSIA.
4. Unplug connectors J4, J5, or J6.
CAUTION!Do not apply diagonal pressure to the DIN connectors (see Figure 16-16 on 
Page 16-15).
5. Disconnect the ALM from the standoffs on the BSIA PCB.
6. Gently lift the ALM out of the BSIA.
7. Replace the BSIA cover and re-install the...

Strata AirLink Systems
BSIA Additional Information
16-34Strata DK I&M 5/99
Initial Configuration Change
It is highly recommended that you get the current configuration and save it to a file on the PC as 
the working copy. Then, open and edit the working copy – not the original file. Using this method 
ensures that the original configuration file is not corrupted while adding or editing existing data. 
Once the new information is saved, the BSIA uses the new data immediately.
Important!Sending...

Strata AirLink Systems
BSIA Additional Information
Strata DK I&M 5/9916-35
Strata AirLink Systems
Communications Port Change 
3. Click Select Database and 
System Settings.
4. Click the Get icon. The current data from the BSIA displays.
5. Enter TRUE in Second Base 
Station Service Enabled.
Important!Do not perform this step without getting the 
current system settings first, or all data is 
overwritten.
6. Save the file and close the 
Configure Window.The Desktop Toolbar displays.
7. Double-click the...

Strata AirLink Systems
RWIU System Installation
16-36Strata DK I&M 5/99
RWIU System Installation
This section describes the specific installation steps for the RWIU PCB.
Step 1: Check the DIP Switches and Jumpers on the PCB
CAUTION!The RWIU and WWIS come from the factory already assembled. Remove the 
WWIS carefully to check the DIP switches on the RWIU, keeping the pins on it 
straight. After checking the DIP switches, but before aligning the two PCBs, be 
sure that the connectors are not bent. This...

Strata AirLink Systems
RWIU System Installation
Strata DK I&M 5/9916-37
Strata AirLink Systems
1. Check DIP Switch S1. Ta b l e  1 6 - 11 gives the factory settings - defaults are in bold.
Important!
lSwitch 8 is used to recover the RWIU in the event of a software load failure. Turn Switch 8 
to its off position to force a download of the stored factory default software.
lIf any Base Station is not used, put its corresponding S1 switch in the on (inactive) 
position. If the switch is in the off position,...

Strata AirLink Systems
RWIU System Installation
16-38Strata DK I&M 5/99
Step 2: Mount the WWIS onto the RWIU
CAUTION!Before aligning the two PCBs, be sure that the connectors are not bent. This 
causes irreparable damage to both PCBs.
1. Carefully align the connectors of the WWIS (P9~P10 and P12~P17) to the terminals on the 
RWIU (J9~J10 and J12~J17) (shown in Figure 16-24).
Figure 16-24 Alignment of the WWIS onto the RWIU
2. Gently press the WWIS onto the RWIU. Ensure that the connections are solid by...