Toshiba Strata Dk14, Dk40i, Dk424 Installation And Maintenance Manual

Peripheral Installation
PC/Data Communications Interface Units
Strata DK I&M    5/9910-69
Peripheral Installation
ä
To connect the PC to the printer
äPress 
DWD&DOO +  on the DKT. 
CONNECT on the PDIU-DS lights. The connection between the PC and the printer is completed, 
as shown in Figure 10-36. (PDIU-DS 203 is in the communication mode).
NoteIf busy tone is sent to the DKT, the connection is not complete; press DWD5HOHDVH and 
Step 3 again.
Operate the PC to print data as required.
Figure 10-36...

Peripheral Installation
PC/Data Communications Interface Units
10-70Strata DK I&M    5/99
NoteWith an RPCI-DI, you may need to switch the RPCI from the TAPI mode to the data 
communication mode before proceeding with Step 3. 
3. To place the RPCI into the data communication mode from the PC keyboard: Set Num Lock
 
ON, and hold the Alt
 key down while typing 240
 (this is HEX F0). 
If the RPCI is in  data communication mode, ATC0
 switches back to TAPI mode.
4.From PC 1’s keyboard, type ATDD204
 and...

Peripheral Installation
PC/Data Communications Interface Units
Strata DK I&M    5/9910-71
Peripheral Installation
Figure 10-37 Internal PC to External PC Test Call Using AT Commands
External PC-to-Internal PC Test
See Figure 10-38 for additional information.
1. Set the RPCI or DIU programming.
©Program 20: Port 000. LEDs 01, 02, 05, and 17 ON; all other LEDs OFF.
©Program 20: Port 004. LEDs 01, 02, 04, and 17 ON; all other LEDs OFF.
©Program 39: Port 000. DWD&DOO (456) and DWD5HOHDVH (454) buttons...

Peripheral Installation
PC/Data Communications Interface Units
10-72Strata DK I&M    5/99
NoteIf using an RPCI-DI, it may be necessary to switch the RPCI from the TAPI mode to the 
Data Communications Mode before proceeding with Step 3. To place the RPCI into the 
data communications mode from the PC keyboard: Set Num Lock 
to ON and type 240
 
while holding the Alt
 key down (this is HEX F0). If in the data communication mode, 
ATC0 will switch the RPCI-DI back to the TAPI mode.
3.From PC 2’s keyboard,...

Peripheral Installation
PC/Data Communications Interface Units
Strata DK I&M    5/9910-73
Peripheral Installation
Notes
lWhen a PDIU-DS is connected with modified RS-232 cable, the READY LED will not light 
until the External and Internal modem establish carrier detect.
lSee “PDIU-DS to Modem Installation”, paragraph three and Figure 10-29 for more details. 
Figure 10-38 External PC to Internal PC Test Call Using Direct CO Line Connection
PC Auto Dial Voice Call Test
There are many off-the-shelf, Windows...

Peripheral Installation
PC/Data Communications Interface Units
10-74Strata DK I&M    5/99
©Program 39: Port 001. DWD&DOO (556) and DWD5HOHDVH (554) buttons are optional. 
If the PDIU-DI is only used for the PC auto dial application, the 
DWD&DOO and DWD
5HOHDVH
 buttons are unnecessary. 
2. Make sure that the auto dial application software is installed on the PC root directory and that 
the communication parameters of the PC and application software are set to the same values. 
NoteIf using an...

Peripheral Installation
DK Alarm Sensor
Strata DK I&M    5/9910-75
Peripheral Installation
Figure 10-39 DK PC Auto Dial Voice Call Test
DK Alarm Sensor
The PIOU or PIOUS PCB provides a circuit that can be set to detect a relay open or closed 
condition from a facility alarm system. When the sensor is activated, all electronic and digital 
telephones sound an alarm signal. The electronic/digital telephone alarm signal can be reset by any 
electronic or digital telephone with an 
$ODUP5HVHW button (see...

Peripheral Installation
Auto Attendant
10-76Strata DK I&M    5/99
Alarm Sensor Wiring
See Figure 10-40, and connect the facility alarm system relay contacts to the PIOU/PIOUS PCB.
Figure 10-40 DK Alarm Sensor Block Diagram (PIOU/PIOUS)
Auto Attendant
Auto Attendant operates like an automatic station attendant or switchboard operator that quickly 
and efficiently distributes calls to stations selected by callers. Incoming calls are greeted by an 
external announcement device that offers callers a menu of...

Peripheral Installation
Auto Attendant
Strata DK I&M    5/9910-77
Peripheral Installation
Strata DK Built-In Auto Attendant (AA)
A built-in Auto Attendant feature is programmed into the Strata DK system software. To enable 
the built-in AA to function, RRCS (-4, -8 or -12) DTMF tone receiver PCB (see Chapter 8 – 
DK40i/DK424 Universal Slot PCB Wiring for RRCS and RKYS installation instructions).
The customer must provide digital announcement device(s), on which the greeting and menu that 
the callers...

Peripheral Installation
Auto Attendant
10-78Strata DK I&M    5/99
Sequence D
The call is not answered after being transferred from the Auto Attendant and is routed back to the 
primary announcement. This is probably the least desirable of the four sequences, since the caller 
hears a repeat of the announcement he just received seconds earlier.
NoteIn all of the above sequences, the call can first ring telephones selected in system 
programming for 12 or 24 seconds, and then be routed to the Auto...