Toshiba Perception Electronic Business Communications System Installation And Maintenance Manual

							Nov. 84 
PRcx;RAMMIK (PEmJMImY) PAm 53 
AUthOriZatiOn PrOcedure must be COnpletd, 
received, 
oroceed as follows: If an NOKql 
response is 
-- ..m.- 
I 10 
I 
,if necessary i 
1. NN = PCB location. 
2, X = Circuit number. 
3. 3, 2, or 1 digit DNs are all 
arenotallowedtogether. if there is no conflict; i.e., 300 and 30 
4, There are 16 different CDS groups which are defined in the 00s Data Block, 
5. Thereareamaximum 
6. XXX= of 32 call Pick-up groups. 
the nmber to which this DN 
hunts. 
NX= Station Hunt - Distributed 
N = Distributed hunt group nun&r (0 - 4) 
x =Membernumber(l-8) 
Nom =Nohunt 
7. DIP = Dial Pulse; TON= MM?; MNL 0 or 
HTL= Hot Line to DN XXX, 1 = Direct Line to ATT 0 or 1; 
8, SDC XX imakes the station a controller of list #XX 
SW XX makes the station a user of list #XX 
Maximum* 25 personal lo-nun&r Speed Dial-Station lists (XX = 1 - 25) 
9. Y = 
wi Waiting feature activated 
N= Czmp-on feature activated 
lOClasses 0 - 
Program. 7 are defined in the Toll Restriction Data Block (DTOL) 
Class 8 is 0, 1 restriction. 
11.m. x = None is no Toll Restriction. 
Ignore line entered 
Ctl H= Backspace 
DEL= Stop printing and return to RIQ 
DELDEL= Abort program  
						

							Nov. 84 
PRCGRAMMIa (PRELJMICJARY) 
PPGE 54 
imm numbex of Display EXTs already assigned 0naximm is 301, 
1 T. 
__ . ,,, r 
I- . . 
Authorization Procedure must be completed, If an OXW response is 
received, proceed as follows: 
NOTES: 
1. Enter a list of all features which are 
Table H-l, it is a list of feature to this group, See 
2. Default = all features allowed. 
3, A maximum of 16 CC6 Groups (O-15) are allowed. 
4. The CO.5 pr twill be repeateduntilDEL,is entered and then aREQ prorq$ 
will be given. 
5*CtlX= Ignore line entered 
Ctl H= 
DEL= mkspace 
Stop printing and return to RnQ 
DEL DEL= 
Abort program  
						

							~av. a4 NG (P-NARY) 
P&SE 55 
--- 
3 IT03 I 
--- 
l 
T13 
1 calls) 
ICED I 
Calf Waitinq  
						

							Nav. 84 
PROGRAMMING (PRELIMINARY) 
PA(;E 56 
received, If an OKn response is 
proceed as follows: 
’ I 
I 
I 
I 
Possible entries are: 
- Misc. Paramters Table 
Q;s- Restriction Class Table 
Ax!- Area/Office Cod@ Exception Table 
ram, WhenTYPEpr 
tis received, proceedas 
Authorization Code 
Number of digits for SPCC.2 
I Aumi2 
1l2orNmE 4 
Authorization Code 
I 
NorEs: 
1. CoupledwithH?C entry in Leas&Co&Routing (DICl) PARTable. Data 
entered here will appar in that table also. 
2. Informs the system if interchangeable codes are used. (Office codes with 
NO/IX format). 
3. SPCCl& 2 entries are theDNof any specialized 
cmmoncarrier (SPCC) used 
(MCI, spcr etc.) or Equal &mess Number (DXXX). data entered herealso 
appears in SMDR ((DMDR) program. 
Data entered here will not appear in SMDR 
output, 
* of digits in the authorization code used. with SPCCl, .%X2. Data 
entered here will not appear in SMDR output. 
Load MVL utility program. 
follows: When TYPE prqt is received, proceed as  
						

							\, 
. 
Nov. 84 PRCCRAMMING (PRELIMINARY) PSE 57 
I NPA-555~XXXX Allo&ed 
Area Code Table=Allow 
A or D 2 
Notes: 
This nunber 
will beusedintheDEKT, 
DSfTandMI;Pdatablocktorespondtothe~L 
prompt. 
2. Defines the Area Code Table of this class as an Allow (A) or Deny (D) type. 
o If Allow (A) is entered, the system will allow all area codes mept 
those deleted in response to the ACD pro@z,x3),- 
o If Derby (D) is entered, the system will deny all area codes except those 
added in response to the ACD pr 
t mote3). -- 
3, used to Add (A) or Delete (D) area codes fran the table (See Note 2). 
e Defines the Office Code Table for this class as an Allow (A) or Deny (D) 
tupe- 
o If Allow (A) is entered, the system will allow all office codes except 
those deleted in response to the WCD proapt (Nos). 
o If Deny (D) is entered, the system will deny all office codes except 
those added in response to the OCD prorqt (Nos). 
5, Used to Add (A) or Delete (D) office codes frcm the table (See Note 4). 
Ttanges we possible (7309 = 730 - 739). 
mad DlKlL utility program, WhenTYPEprmptis received, proceedas 
follows: 
ITEN PROW 
USER EWRY 
-1 
TYPE 
TableNumber 
0 31 
AreaCode 
N O/IX, NONE 1 
Class Number 
0 1 etc., NONE 
Office Codes 
OFC 
A NXXX MM etc. 
I 
2,3 1 
- or - 
I 
I  
						

							Nov. 8 
(PRELIMINARY) 
PAGE 58 
identifies the area code that this ACE is assigned to. 
@3-2 9, x=4 9). Format is N 0/1x 
A maximm of eight (8) AK! tables can be assigned to any 
oneareacodeand those table mmbers (TNO, Note11 mstbe sequential.. 
2. Used to add (A) or delete (D) office codes from the table. Office codes 
entered will be an exception to the area code and class listed. 
Ranges are possible (7309 = 736 - 7391, 
3. Codes cannot be edanddeletedin the samepass through the table. A 
separate pass is required 
for each step. 
Codes cannotbeaddedanddeleted in the 
se,parate pass is required for each step, pass through the table. A 
Program : 
Error Code 
-0 
ER!IIXDOl 
ERTRDO2 
EzI!mDO3 
EBTRDO4 
ERTRDo5 
ERTRDOG 
EzTRDo7 TLoll Restriction Data Block WIOL) 
(M 0/1x) is out of range. 
ric error. (0 91 
Authorization Code is out of range. (0 12) 
Class No. is a& of range (0 7) 
Numberofareacodeisover 0nax20) 
!Sk3&er of office code is over 0uax 20) 
is out of range. (0 31) 
bx 8) 
Authorization Procedure mst be 
received, proceed as follows: If an OK? response is  
						

							Nov. 84 
PRcmAmING(PRRLIMI~) 
PAGE 59 
NOTES: 
1. xx = List Nlileer. 
00 = System List (90 nurbers maximum). 
Ol--25 = Station Lists (10 numbers each maximm). 
2. Input procedure is: 
Address Code-Space-Access Ccxde-Pause-Dn 
For exaqle: 01 9* 
3. Stored nunbersmaybe 
between 1 and 16 digits: * 
3-second pause and is counted as one of the 16 digits. 
4. If the List Nunber &NO) was 00 (System List), %-digit 
ess cedes will 
he used (lo- 
5,Nofurtherpr ; will be given until DEL is entered, 
6. Ctl X = Ignor 
CtlH=Rackspace 
inting and return to 
rt program 
Authorization Procedure rtplst be 
leted. 
received, proceed as follows: If an OK response is 
1. SPCCl& SPCC 2 entries are theDNof any SpecializedC nCa.rrier (WCC) 
used (MCI, WC, etc.) or Qua1 kess Number (10xXx). Data entered here 
also appears in Toll Restriction (rrrOL) PAR table. 
(Data entered here will 
not appear in SMDR output). 
2. Enter the trunk group number and type of calls to be recorded on this Trunk 
Group:NONS 
INC - Incoming Only 
OGT- Outgoing Only 
IAO- Incoming and Outgoing 
ML - 
Toll Only 
INT- Incoming - all 
- Outgoing - toll only  
						

							. 84 
PEGRAMMING(PWNARY) E 60 
3. TGP continues to be proc@ed until DE% is entered, 
4.ctlx= Ignore line entered 
Ctl H= Backspace 
DEL= Stop printing and return to REQ 
DELDEL= Abort program 
Authorization Procedure nust be 
leted, 
received, proceed as follows: If an WV response is 
NOTES: 
1, XX=AccessCodeof thePage Zoneor All Page. 
2, Ctl X = Ignore line entered 
CtlH=EWcspace 
DEL- Stop printing and return to 
DELDEL= 
Abort program  
						

							Nov. 84 
(PRELJMINARY) PAGJZ 61 
Authorization Procedure must be 
leted, If an OK response is 
received, proceed as follows: 
NOTES: 
1. RPT = Report Commnd-if the program had been started previously, a re,port 
would follow. See Table M-1 for format, 
STT= Start Cmmand-usedtoinitialize theprogramaud start the record 
keeping reporting activity. (Used for SCH = cm only. Must be entered 
after each Rw! request.) 
CBS = change Ccmand-used to alter reporting parameters. 
OUT=OutCmnand-used to stop repor 
2. System outputs the date in its memory 
M&Day, Year). Anentry 
(MMDDYY) will overwrite the existing data. A carriage return (CR) = no 
change. 
3. System outputs the time in its memory (Hours, Minutes, Seconds1. An entry 
(HEWMSS) will overwrite the existing data, A carriage return (CR) = ho 
change. 
Schedule of Reports: 
e 30 = Report every 30 minutes beginning at the.tim listed as STR.DATR (Note 
5) andSTR.TIME (Note 61, 
60 = Report every 60 minutes beginning at the time listed as STR.DATE (Note 
5) and STR.TIME (Note 6). 
CMD=Reportonlywhen theRPT 
comnand is given (Note 1). 
5, Date that record keeping and reporting should start. 
The system outputs 
the date in its mmry (Month, Day, Year). An entry (WDDYY) will 
overwrite the existing data. A carriage return (CR) = no change,, 
6. Tim that record keeping and reporting should start. The system the time 
in its memory (Hours, Minutes, Seconds). 
Ah entry (HHMMSS) will overwrite 
the existing data, A carriage return (CR) = no change, 
7, Enter Y (yes) or N (no) followed by a carriage return to select the 
parameters to be reported (see Table M-2). 
8. Ctl X = Ignore line entered 
Ctl H= Backspace 
Dm= 
Stop printing and return to REI;2 
DELDEL= Abort program  
						

							PR0SAMMIa (PRELIMINARY) 
P&SE 62 
I i RFTFFtClM i MMnnYY 
I 
I , ““.‘., 
runk Groups Ol--15 are reported in the same way as Group 00. 
Averaqe Tim to Answer 
dgoing CallI 
Peg Cmt 
All Trunks Busy 
Peg count 
j%~~nk Groups 01-15 are reported in the sam way as Group 00.