Toshiba Estudio 230 Manual

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 35
2
[FAX] button: ON ([FAX] LED: ON)
Digital  key Button Items to check Contents
Highlighted  display
e.g. Normal dis-
play
e.g.
[1] A -
- -
B - - -
C 24 V power supply Power ON Power OFF
D IPC board connection Not connected Connected
E - - -
F Polygonal motor rotation status (Motor is rotating  at Output 
Mode (03)) Abnormal rota- 
tionNormal rota-
tion
G Auger lock switch Lock Unlock
H Toner cartridge...

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 36
[5]
A -
- -
B - - -
C - - -
D - - -
E - - -
F RADF connection RADF con-
nected Not connected
G Platen sensor Platen cover 
opened Platen cover  
closed
H Carriage home position sensor Carriage at  home positionOther than  
home position
[6] A -
- -
B - - -
C - - -
D APS sensor (APS-R) No original Original 
present
E APS sensor (APS-C) No original Original 
present
F APS sensor (APS-3) No original Original...

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 37
2
Table 2. Connecting status of additional options at  inner area of the equipment
[9]A Bridge unit/Job Separator/Offset Tray connection d
etection-
3 Refer to table 2
B Bridge unit/Job Separator/Offset Tray connection d etection-
2 Refer to table 2
C Bridge unit/Job Separator/Offset Tray connection d etection-
1 Refer to table 2
D - - -
E - - -
F - - -
G - - -
H - - -
[0] A Dongle (for Printer/Scanner...

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 38
[FAX] button: OFF/ [COPY] button: ON ([FAX] LED: OF F/ [COPY] LED: ON)
*1  Be sure to install the USB storage device to the e quipment and check if the device can be used 
with this code.
 Be sure to turn OFF the write protection (the func tion to prevent data from erasure by the acci-
dental recording or deleting) of the USB storage de vice before performing the check, otherwise 
this code cannot be...

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 39
2
2.2.3 Output check (test mode 03)
 
Procedure 1 
Procedure 2 
Procedure 3 
Procedure 4 Status of the output signals can be checked by keyin
g in the following codes in the test mode 03.
[0][3]
[POWER] [POWER] OFF/ON
(Exit)
[START]
(Code) Operation
ON Stop
code Operation
OFF[START]
[0][3]
[POWER] [POWER] OFF/ON
(Exit)
[START] [CLEAR]
Operation
One direction Test mode
standby(Code)
[0][3]
[POWER] [POWER]...

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 40
Code Function Code Function Procedure
101 Main motor ON (operational without  developer unit) 151 Code No. 101 function OFF 1
102 Toner motor ON (normal rotation) 152 Code No. 102  function OFF 1
103 Polygonal motor ON (600 dpi) 153 Code No. 103 func tion OFF 1
108 Registration clutch ON 158 Code No. 108 function O FF 1
109 PFP motor ON 159 Code No. 109 function OFF 1 110 ADU motor ON (low speed) 160 Code...

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 41
2
Code Function Procedure
271 LCF tray-up motor (up/down) 2
278 PFP upper drawer tray-up motor ON (tray up) 2
280 PFP lower drawer tray-up motor ON (tray up) 2
281 RADF feed motor ON/OFF (normal rotation) 3
282 RADF feed motor ON/OFF (reverse rotation) 3
283 RADF read motor ON/OFF (normal rotation) 3
284 RADF reverse motor ON/OFF (normal rotation) 3
285 RADF reverse motor ON/OFF (reverse rotation) 3
289...

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 42
2.2.4 Test print mode (test mode 04)

Notes: 
1. When an error occurs, it is indicated on the panel , but the recovery operation is not per-
formed. Turn OFF the power and then back ON to clea r the error.
2. During test printing, the [CLEAR] button is disab led when “Wait adding toner” is displayed.
The embedded test pattern can be printed out by key
ing in the following codes in the test print mode...

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 43
2
2.2.5 Adjustment mode (05) (e-STUDIO200L/230/280)
Procedure 1 
Procedure 2 
Procedure 3 
Procedure 4 Items in the adjustment mode list in the following 
pages can be corrected or changed in the adjust-
ment mode (05). Turn ON the power with pressing the  digital keys [0] and [5] simultaneously in 
order to enter this mode.
[0][5]
[POWER] [POWER]
OFF/ON
(Exit)[Digital key] (Code) [START]
[CANCEL]...

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 44
Procedure 6 
* When the automatic adjustment ends abnormally, err or message is displayed.
Procedure 7 
* When the automatic adjustment ends abnormally, err or message is displayed.
Procedure 10 
Procedure 17
* When the “storing is not performed within 2 minute s after pressing the [START] button at the 
manual adjustment, the “automatic adjustment” start s automatically.
Note: Note: 
The fuser roller...