Home > Toshiba > Printer > Toshiba Estudio 230 Manual

Toshiba Estudio 230 Manual

Here you can view all the pages of manual Toshiba Estudio 230 Manual. The Toshiba manuals for Printer are available online for free. You can easily download all the documents as PDF.

Page 41

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 5
2
E910 Finisher jam (Bridge unit) Jam at the bridge unit transport sensor-1: The  
paper does not reach the bridge unit transport sen- 
sor-1 after it has passed the exit sensor. P. 5-35
E920 Stop jam at the bridge unit transport sensor-1:  The 
trailing edge of the paper does not pass the bridge  
unit transport sensor-1 after its leading edge has 
reached the sensor. P. 5-35
E930 Jam at the bridge unit...

Page 42

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 6
EAE0 Finisher jam Receiving time time-out jam: The pr
inting has been 
interrupted because of the communication error  
between the equipment and finisher when the 
paper is transported from the equipment to the fin- 
isher. P. 5-46
EAF0 Finisher jam (Finisher unit) Stack return jam: It cannot load the paper which  
passed through the delivery roller on the intermedi-
ary process tray. [MJ-1022] P. 5-44...

Page 43

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 7
2
2.1.2 Service call
Error code Classification Contents Troubleshooting C010 Drive system  related service call Main motor abnormality: The main motor is not rotat
ing 
normally. P. 5-47
C040 Paper feeding sys- tem related ser- 
vice call PFP motor abnormality: The PFP motor is not rotating  
normally.
P. 5-48
C130 Upper drawer tray abnormality: The upper drawer  tray 
motor is not rotating or the upper...

Page 44

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 8
C940 Circuit related ser-
vice call Engine-CPU abnormality
P. 5-76
C970 Process related  service call High-voltage transformer abnormality: Leakage of th
e 
main charger is detected. P. 5-76
CA10 Laser optical unit  related service call Polygonal motor abnormality: The polygonal motor is
 not 
rotating normally. P. 5-60
CA20 H-Sync detection error: H-Sync detection PC boa rd can-
not detect laser beams. P....

Page 45

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 9
2
CDC0 Finisher related  service call Punch power failure abnormality: 24 V is not applie
d to 
the punch controller board. 
[MJ-1025 (when MJ-6005 is installed)] P. 5-74
CDD0 Folding position sensor abnormality: Automatic  adjust-
ment of the folding position sensor can not be perfo rmed 
properly. [MJ-1025] P. 5-74
CDE0 Paddle motor abnormality: The paddle motor does  not 
rotate properly. [MJ-1025] P....

Page 46

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 10
2.1.3 Error in Internet FAX / Scanning Function
1) Internet FAX related error 
(when GM-1020/3020, 1030/3030, 2020 or 2030 is inst alled (e-STUDIO200L/230/280))
(when GM-1070/4070, 1080U/4080U, 2070 or 2080U is i nstalled (e-STUDIO202L/232/282))
Error code Contents Troubleshooting
1C10 System access abnormality P. 5-79
1C11 Insufficient memory P. 5-79
1C12 Message reception error P. 5-79
1C13 Message...

Page 47

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 11
2
2) RFC related error  (when GM-1020/3020, 1030/3030, 2020 or 2030 is inst alled (e-STUDIO200L/230/280))
(when GM-1070/4070, 1080U/4080U, 2070 or 2080U is i nstalled (e-STUDIO202L/232/282))
Error codeMessage displayed in the 
TopAccess screen Contents Troubleshooting
2500 Syntax error, command unrecog- nized HOST NAME error (RFC: 500) 
Destination mail address error 
(RFC: 500)
Terminal mail address...

Page 48

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 12
3) Electronic Filing related error
Error code Message displayed in the 
TopAccess screen Contents Troubleshooting
2B10 There was no applicable job. No applicable job e rror in job control 
module P. 5-83
2B11 Job status failed. JOB status abnormality P. 5-83
2B20 Failed to access file. File library function err or P. 5-83
2B30 Insufficient disk space. Insufficient disk space  in /SHR partition P. 5-83...

Page 49

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 13
2
4) E-mail related error  (when GM-1020/3020, 1030/3030, 2020 or 2030 is inst alled (e-STUDIO200L/230/280))
(when GM-1070/4070, 1080U/4080U, 2070 or 2080U is i nstalled (e-STUDIO202L/232/282))
Error codeMessage displayed in the 
TopAccess screen Contents Troubleshooting
2C10 Illegal Job status System access abnormality P. 5 -85
2C11 Not enough memory Insufficient memory P. 5-85
2C12 Illegal Job status...

Page 50

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 14
5) File sharing related error (when GM-1020/3020, 1030/3030, 2020 or 2030 is inst alled (e-STUDIO200L/230/280))
(when GM-1070/4070, 1080U/4080U, 2070 or 2080U is i nstalled (e-STUDIO202L/232/282))
Error codeMessage displayed in the 
TopAccess screen Contents Troubleshooting
2D10 Illegal Job status System access abnormality P. 5 -88
2D11 Not enough memory Insufficient memory P. 5-88
2D12 Illegal Job status...
Start reading Toshiba Estudio 230 Manual

Related Manuals for Toshiba Estudio 230 Manual

All Toshiba manuals