Home > Toshiba > Printer > Toshiba Estudio 230 Manual

Toshiba Estudio 230 Manual

Here you can view all the pages of manual Toshiba Estudio 230 Manual. The Toshiba manuals for Printer are available online for free. You can easily download all the documents as PDF.

Page 11

1
2
3
4
5
6
7
8
9
10
1. SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES
2. ERROR CODE AND SELF-DIAGNOSTIC  MODE
3. ADJUSTMENT 
4. PREVENTIVE MAINTENANCE (PM)
5. TROUBLESHOOTING 
6. FIRMWARE UPDATING 
7. POWER SUPPLY UNIT
8. REMOTE SERVICE 
9. DATA CLONING with USB STORAGE DEVICE  (e-STUDIO202L/232/282)
10. WIRE HARNESS CONNECTION DIAGRAMS 

Page 12


				            

Page 13

1
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES
1 - 1
1. SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES 
1.1 Specifications

Copy process Indirect electrophotographic process (dr y)
 Type Desktop type (console type: when paper feed pede stal (PFP) and large 
capacity feeder (LCF) are installed)
 Original table Fixed type (the left rear corner used  as guide to place originals)
 Accepted originals Sheet, book and 3-dimensional obj ect. The...

Page 14

e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA  TEC
1 - 2
* When the RADF is used, the copy speed of {20}23[28 ] sheets per minute is only available under the 
following conditions: 
 Original/Mode: Single side original/A4/LT size. APS /automatic density are not selected.
 Number of sheets: {20}23[28] or more.
 Reproduction ratio: 100%
Copy speed for thick paper (Copies/min.) 
e-STUDIO200/200L/230/232/280/282 series 
Thick 1 (81 g/m
2 to 105...

Page 15

1
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES
1 - 3
* System copy speed 
* The system copy speed, including scanning time, is  available when 10 sheets of A4/LT size original 
are set on RADF and one of the copy modes in the ab ove table is selected. The period of time from 
pressing [START] to the paper exit completely out o f the equipment based on the actually measured 
value.
* Upper drawer is selected and copying is at the non -sort...

Page 16

e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA  TEC
1 - 4
 Eliminated portion.................... Leading edges : 3.0±2.0 mm, Side/trailing edges: 2.0±2.0 mm (copy )
Leading / trailing edges: 5.0±2.0 mm, Side edges: 5 .0±2.0 mm (print)
 Paper feeding .......................... Standard dra wers:
1 or 2 drawers (stack height 60.5 mm, equivalent to  550 sheets; 
64 to 80 g/m
2 (17 to 22 lb. Bond)): Depends on destinations or 
versions.
PFP: Option...

Page 17

1
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES
1 - 5
 Dimensions of the equipment ...................... Se e the figure below (W 637 x D 719 x H 739 (mm))
* When the tilt angle of the control panel is 45 deg rees.
 Fig. 1-1
7 1 9
7 3 9
6 3 74 5 °
04/09 

Page 18

e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA  TEC
1 - 6
1.2 Accessories
Machine version
NAD: North America 
ARD: Argentina
ASD: Central and South America / Hong Kong 
AUD: Australia 
MJD: Europe 
ASU: Asia
SAD: Saudi Arabia
IRD: Iran 
CND: China 
TWD: Taiwan 
JPD: Japan
KRD: Korea
*1: e-STUDIO200L/230/230L/280/280S only 
*2: In e-STUDIO202L/232/232S/282/282S, 2 discs are  included.
Unpacking/setup instruction 1 set 
Operator’s manual 3 pcs....

Page 19

1
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES
1 - 7
1.3 Options 
1.3.1 e-STUDIO200L/230/230L/280/280S
* 1) N: North America E: Europe F: France S: Sweden
Notes: 
 The bridge unit (KN-3520) is necessary for install ation of the finisher (MJ-1022, MJ-1025).
 The finisher (MJ-1025) is necessary for installati on of the hole punch unit (MJ-6005N/E/F/S).
 The PCI slot (GO-1040) is necessary for installati on of the scrambler board (GP-1030)...

Page 20

e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA  TEC
1 - 8
1.3.2 e-STUDIO202L/232/232S/282/282S
* 1) N: North America   E: Europe   F: France   S: 
Sweden
Notes: 
1. The bridge kit (KN-3520) is necessary for install ation of the finisher (MJ-1022 or MJ-1025).
2. The saddle stitch finisher (MJ-1025) is necessary  for installation of the hole punch unit 
(MJ-6005N/E/F/S).
3. The PCI slot (GO-1060) is necessary for installat ion of the scrambler board...
Start reading Toshiba Estudio 230 Manual

Related Manuals for Toshiba Estudio 230 Manual

All Toshiba manuals