Toshiba Estudio 230 Manual

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 45
2
Test print pattern in Adjustment Mode (05) 
Operation: One test print is printed out when the [ FAX] button is pressed after the code is keyed in a t 
Standby Screen.
Code Types of test pattern Remarks
1 Grid pattern Refer to 3.2.3 Printer related adjustment
3 Grid pattern (Duplex printing) Refer to 3.2.3 Print er related adjustment 

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 46
Notes:  The digit after the hyphen in “Code” of the follow ing table is a sub code.
 In “RAM”, the NVRAM of the board in which the data  of each code is stored is indicated. “M” 
stands for the LGC board and “SYS” stands for the S YS board.
Adjustment mode (05) 
Code Classi-
fication Items
Func-
tion Default
 RAM Contents
Proce-
dure
200 Devel- operAutomatic adjustment of  
auto-toner sensor 
(Fuser...

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 47
2
306 Scanner Image location adjustment  of primary scanning direc- 
tion 
(scanner section) ALL 156
 SYS When the value 
increases by “1”, the  
image shifts by approx.  
0.0846 mm toward the 
front side of the paper. 1
308 Scanner Distortion mode ALL - - Moves carriages to th e 
adjusting position.  
(Chap. 3.2.4) 6
340 Scanner Reproduction ratio adjust- ment of secondary scan- 
ning direction 
(scanner...

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 48
367 RADF RADF original guide width 
adjustment 
(Minimum) ALL - - Stores the current width 
of RADF original guide 
by keying in this code  
with the guide set at the 
minimum width. Perform  
this adjustment when the  
RADF board or volume is 
replaced, or when the  
code (05-356) is per- 
formed. 6
368 RADF RADF original guide width  adjustment 
(Maximum) ALL - - Stores the current width 
of RADF...

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 49
2
430 Image Top margin adjustment (blank area at the leading  
edge of the paper) PPC 0
 M When the value 
increases by “1”, the 
blank area becomes  
wider by approx.
0.0423 mm. 1
431 Image Left margin adjustment (blank area at the left of the 
paper along the paper  
feeding direction) PPC 0
 M 1
432 Image Right margin adjustment (blank area at the right of  
the paper along the paper  
feeding...

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 50
448-0 Paper 
feeding Paper aligning  
amount  
adjustment at  
the registra-
tion section 
(PFP upper  
drawer/Plain  
paper) Long size ALL 10
M When the value 
increases by “1”, the  
aligning amount  
increases by approx.
0.8 mm. 
 
Long size:330 mm or longer
Middle size:
220 mm to 329 mm
Short size: 219 mm or shorter 4
448-1 Middle  sizeALL 10
 M 4
448-2 Short size ALL 8 M 4
449-0 Paper  feeding Paper...

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 51
2
458-0 Paper  feeding Paper aligning  
amount  
adjustment at  
the registra-
tion section 
(Bypass feed- 
ing/Plain  
paper) Long size ALL 26
M When the value 
increases by “1”, the  
aligning amount  
increases by approx.
0.8 mm. 
 
Long size:330 mm or longer
Middle size:
220 mm to 329 mm
Short size: 219 mm or shorter
* Postcard is sup-
ported only for JPN  
model. 4
458-1 Middle  sizeALL 26
 M 4
458-2...

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 52
466-0 Paper 
feeding Adjustment of  
paper push- 
ing amount/ 
Bypass feed-
ing Plain 
paper
ALL 0
 M When the value 
increases by “1”, the  
driving speed of bypass  
feed roller increases by 
approx. 0.2 ms when the  
paper transport is started  
from the registration sec-
tion. 
* Postcard is sup-ported only for JPN  
model. 4
466-1 Postcard ALL 0 M 4
466-3 Envelope ALL 0 M 4
466-4 Thick  paper 1ALL 0...

June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 53
2
472-0 Paper  feeding Paper aligning  
amount  
adjustment at  
the registra-
tion section 
(PFP lower  
drawer/Thick  
paper 1) Long size ALL 20
M When the value 
increases by “1”, the  
aligning amount  
increases by approx.
0.8 mm. 
 
Long size:330 mm or longer
Middle size:
220 mm to 329 mm
Short size: 219 mm or shorter 4
472-1 Middle  sizeALL 22
 M 4
472-2 Short size ALL 19 M 4
473 Paper  feeding...

e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 54
508 Image Density 
adjustment  
Fine adjust- 
ment of “man-
ual density”/ 
Dark step  
valueText/Photo PPC EUR:20
UC:20
JPN:30
 SYS When the value 
increases, the image of  
the “dark” steps  
becomes darker. 1
509 Photo PPC EUR:24 UC:24
JPN:24
 SYS 1
510 Text PPC EUR:20 UC:20
JPN:27
 SYS 1
512 Image Density  adjustment  
Fine adjust- 
ment of “auto- 
matic density”Photo PPC 128
SYS When the value...