Toshiba Estudio 230 Manual

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 ADJUSTMENT
3 - 95
3
3.13 Adjustment of the Finisher (MJ-1025) 
3.13.1 Adjusting the folding position (Electrical sy stem (Finisher/Saddle 
unit))
The folding position is adjusted by matching it wit h the stapling position.
If you have replaced the finisher controller PCB, y ou must transfer the existing settings to the new PC B. 
Perform the following if the folding position must  be adjusted for some reason.
Note: Note: 
Both the folding and...

e-STUDIO200L/202L/230/232/280/282 ADJUSTMENTJune 2004 © TOSHIBA TEC
3 - 96
3.13.2 Adjusting the sensor output (Electrical syste
m (Puncher unit; 
option))
Perform the following when the punch controller PCB , horizontal registration sensor (photosensor PCB/
LED PCB), or waste full sensor (waste full photosen sor PCB/waste full LED PCB) has been replaced.
 (1) Shift bits 1 through 4 on the punch controller P CB as follows:
 Fig.3-130
(2) Press SW1002 or SW1003 on the punch controller P CB. A press will...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 ADJUSTMENT
3 - 97
3
3.13.3 Registering the number of punch hole (Electri cal system 
(Puncher unit; option))
Perform the following to register the type of punch er unit (number of holes) used to the IC on the pun ch 
controller PCB for identification by the finisher.  Be sure to register the type whenever you have replac ed 
the punch controller PCB. 
.
(1) Set bits of 1 through 4 on the DIPSW1001 on the  punch controller PCB as follows:...

e-STUDIO200L/202L/230/232/280/282 ADJUSTMENTJune 2004 © TOSHIBA TEC
3 - 98
3.13.4 After replacing the EEP-ROM (IC1002) (Electri
cal system 
(Puncher unit; option))

(1) Turn off the host machine. 
(2) Set bits 1 through 4 on the punch controller PCB  as follows:
 Fig.3-132
(3) Press SW1002 and SW1003 on the punch controller  PCB at the same time.
 The presses will initialize the EEP-ROM. At the en d, all LEDs (LED1001, LED1002, 
LED1003) will go ON.
(4) Adjust the sensor output, and store the number o f...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 ADJUSTMENT
3 - 99
3
3.14 Key Copy Counter (MU-8, MU-10)
To make a key copy counter available, the following  2 components must be installed to the equipment.
 Fig.3-133

(1) Remove the rear cover. 
(2) Remove the right upper cover-3, and cut  open the window for the key copy counter.
 Fig.3-134
(3) Pull out the harness connector from the hole 
of the machine frame, and cut the short har- 
ness of the connector. (Treat the cut harness 
properly to...

e-STUDIO200L/202L/230/232/280/282 ADJUSTMENTJune 2004 © TOSHIBA TEC
3 - 100
(4) Connect the connector of the counter socket  to the harness connector of the equipment  
side.
(5) Install the counter socket to the machine  frame with two screws.
(6) Reattach the cover.
 Fig.3-136
(7) Insert the key copy counter with its arrow  mark pointing the rear side of the equipment.
 Fig.3-137
(8) Enter the value “3” in the setting mode (08-202).
Screw
Counter socket
Harness connector
Key copy counter 

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 ADJUSTMENT
3 - 101
3
3.15 Adjustment of Dogleg
Dogleg is the name given to an image which is defor med approx. 48 mm of the trailing edge of the out-
put paper. 
Since adjustment has usually been performed when th e equipment was manufactured, dogleg image 
should not occur. However, if the following dogleg  image A or B does happen to occur, the following 
adjustment must be performed. An original with a li ne parallel to the feeding direction is...

e-STUDIO200L/202L/230/232/280/282 ADJUSTMENTJune 2004 © TOSHIBA TEC
3 - 102

(2) Remove the 2 adjustment screws.
(1) Check the position of the adjustment screws.
 Fig.3-141
06/01 

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 ADJUSTMENT
3 - 103
3
(3) Fix the adjustment screws in the position as sho wn in the figure.
 Dogleg image A Install the adjustment screws as shown in the figur e below so that the stay of the fuser unit 
can move upward.
 Fig.3-142
 Dogleg image B
Install the adjustment screws as shown in the figur e below so that the stay of the fuser unit 
can move downward.
 Fig.3-143
(4) Check the copied image. If further adjust- ment is needed, fix the...

e-STUDIO200L/202L/230/232/280/282 ADJUSTMENTJune 2004 © TOSHIBA TEC
3 - 104