Toshiba Estudio 162 Owners Manual

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 2 24 01 JAM total counter clear (JAM TTL CLR.)
04 ADF counter clear (ADF CLR.) (Disabled when set to 
OC) (Executable only when the ADF is installed.)
05 Duplex counter clear (DPLX CLR.) (Enabled when 
Duplex setting is ON)
06 Developer counter clear (DVLP CLR.)
07 Drum counter clear (DRUM CLR.)
08 Copy counter clear (COPIES CLR.)
09 Printer counter clear (PRT.CLR.)
10 FAX counter clear (FAX CLR.) (Executable only when the 
FAX is installed.)...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 3
4. Descriptions of various test commands
66 34 Communication time measurement (Executable only 
when the FAX is installed.)
37 Speaker sound volume setting (Executable only when 
the FAX is installed.)
38 Time setting/check (Executable only when the FAX is 
installed.)
41 CI signal check (Executable only when the FAX is 
installed.) Main 
codeSub 
codeContents
Main 
codeSub 
codeContents Details of function/operation
1 01 Mirror scan (SCAN...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 4 2 02 ADF sensor status display 
(ADF SENSOR) (Disabled 
when set to OC) (Executable 
only when the ADF is 
installed.)[Function]
The ON/OFF status of the ADF sensors can be checked with the LCD.
When a sensor is ON, the sensor name is displayed on the LCD. 
[Operation]
03 ADF motor operation check 
(ADF MOTOR CHK) 
(Disabled when set to OC) 
(Executable only when the 
ADF is installed.)[Function]
When [OK (ENTER)/START] key is pressed, the...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 5 5 01 Operation panel display 
check (LCD/LED CHK)[Function]

When [OK (ENTER)/START] key is pressed, all the LCDs on the operation panel are turned ON (all
pixels ON).
After 5sec of ON, the machine goes into the sub code entry standby mode.
When [MODE SWITCH] key is pressed under the all ON state,  the mode is shifted to the individual
ON mode, where the LEDs are turned on one by one from the left upper end to the left lower side
then from...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 6 6 01 Paper feed solenoid 
(CPFS1, CPFS2, MPFS) 
operation check (PSOL 
CHK)[Function]
When [OK (ENTER)/START] key is pressed, the selected paper feed solenoid repeats ON for 500ms
and OF for 500ms 20times.
When [
←/→/10KEY] is pressed, the paper feed solenoid setting is switched.
[Operation]
02 Resist roller solenoid (RRS) 
operation check (RES.R 
SOL CHK)[Function]
When [OK (ENTER)/START] key is pressed, the resist solenoid repeats ON for...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 7 8 01 Developing bias output 
(DVLP BIAS SET.)[Function]
When [OK (ENTER)/START] key is pressed, the developing bias signal is turned ON for 30sec.
When, however, an actual output value is measured, use test command 25-01.
After completion of this process, the machine goes into the sub code entry standby mode.
[Operation]
02 Main charger output (Grid 
HIGH) (MHV(H) SET.)[Function]
When [OK (ENTER)/START] key is pressed, the main charger is...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 8 10 00 Toner motor operation 
(TONER MOTOR)[Function]
When [OK (ENTER)/START] key is pressed, the toner motor is rotated for 30sec.
After completion of this process, the machine goes into the main code entry standby mode.
[Operation]
14 00 Cancel of trouble other than 
U2 (TRBL CANC.)[Function]
Used to cancel troubles other than U2.
∗Cancel troubles such as H trouble which writes data into EEPROM, and perform hardware reset. 
[Operation]
16 00...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 9 22 02 Maintenance preset display 
(M-CNT PRESET)[Function]
The quantity (25,000 sheets, etc.) corresponding to the code set with TC21-01 is displayed.
[Operation]
04 JAM total counter display 
(JAM TTL CNT)[Function]
The JAM total counter is displayed.
[Operation]
05 Total counter display (TTL 
CNT)[Function]
The total counter value is displayed.
[Operation]
06 Developer counter display 
(DVLP CNT)[Function]
The developer counter data is...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 10 22 14 ROM version display (ROM 
VER.)[Function]
The P-ROM version is displayed.
Press [
←/→/10KEY] to switch the display version.
[Operation]
16 Duplex counter display 
(DPLX CNT) (Enabled when 
Duplex setting is ON) 
(Executable only when the 
RADF is installed.)[Function]
The duplex counter is displayed.
[Operation]
17 Copy counter display 
(COPIES CNT)[Function]
The copy counter is displayed.
[Operation]
18 Printer counter display...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 11 22 21 Scanner counter display 
(SCAN CNT)[Function]
The scanner counter is displayed.
[Operation] 
22 ADF JAM counter display (S 
JAM CNT) (Disabled when 
set to OC) (Executable only 
when the ADF is installed.)[Function]
The ADF JAM counter is displayed.
[Operation]
24 01 JAM total counter clear (JAM 
TTL CLR.)[Function]
When [OK (ENTER)/START] key is pressed, the JAM total counter is cleared to 0 and 000,000 is
displayed on the LCD....