Toshiba Estudio 162 Owners Manual

e-STUDIO162/162D/151/151D UNPACKING AND INSTALLATION  5 - 2
4. Unpacking
Be sure to hold the handles on both sides of the machine to unpack the
machine and carry it to the installation location.
5. Removing protective packing materials
1) Remove all pieces of tape shown in the illustration below and then
open the ADF/RADF and remove the protective materials. Take out
the bag containing the toner cartridge.
2) Release the scan head locking switch.
3) Open the bypass tray, and then open the side cover...

e-STUDIO162/162D/151/151D UNPACKING AND INSTALLATION  5 - 3 9) Shake the aluminum bag to stir developer
10) Supply developer from the aluminum bag to the top of the MX
roller evenly.
Note: Be careful not to splash developer outside Developer unit.
11) Attach Upper developer unit and fix it with a screw.
12) Rotate the MG roller gear to distribute developer evenly.
Note: Never rotate the gear in the reverse direction.
Note: When carrying Developer unit, do not tilt it extremely as
shown with the arrow in...

e-STUDIO162/162D/151/151D UNPACKING AND INSTALLATION  5 - 4
8. Loading the paper tray
Note: Make sure that the paper is not torn, is free of dust, and has no
wrinkles or curled edges.
1) Raise the handle of the paper tray and pull the paper tray out until it
stops.
2) Remove the pressure plate lock. Rotate the pressure plate lock in
the direction of the arrow to remove it while pressing down on the
pressure plate of the paper tray.
3) Store the pressure plate lock which has been removed in step 2. To...

e-STUDIO162/162D/151/151D UNPACKING AND INSTALLATION  5 - 5
A. Before Installation
(1) Hardware and software requirements
Check the following hardware and software requirements in order to
install the software.
*
1The machines USB connector will transfer data at the speed speci-
fied by the USB 2.0 (Hi-Speed) only if the Microsoft USB 2.0 driver is
preinstalled in the computer, or if the USB 2.0 driver for Windows
2000 Professional/XP that Microsoft provides through its Windows
Update is installed.
*...

e-STUDIO162/162D/151/151D UNPACKING AND INSTALLATION  5 - 6 8) When the Finish screen appears, click the Close button.
A message will appear instructing you to connect the machine to
your computer. Click the OK button.
Caution: If you are running Windows 2000/XP and a warning message
appears regarding the Windows logo test or digital signature,
be sure to click Continue Anyway or Yes.
Note: After the installation, a message prompting you to restart your
computer may appear. In this case, click the Yes...

e-STUDIO162/162D/151/151D UNPACKING AND INSTALLATION  5 - 7
11) You will return to the window of step 8). If you wish to install Button Man-
ager or Desktop Document Manager, click the Utility Software button.
If you do not wish to install the Utility Software, click the Close
button and go to step 14).
Note: After the installation, a message prompting you to restart your
computer may appear. In this case, click the Yes button to
restart your computer.
Installing the Utility Software
12) Click the Button...

e-STUDIO162/162D/151/151D UNPACKING AND INSTALLATION  5 - 8 5) When you are asked how the printer is connected, select Con-
nected to this computer and click the Next button.
6) When the interface selection screen appears, select USB and
click the Next button.
If you are using the machine as a shared printer on a network,
select Connected via the network. For more information on this
setting, see Using the machine as a shared printer.
Follow the on-screen instructions.
Caution: If you are running Windows...

e-STUDIO162/162D/151/151D UNPACKING AND INSTALLATION  5 - 9 7) Select the printer port and whether the machine is to be used as the
default printer, make the selections and click the Next button.
Select LPT1 for the printer port.
Note:
•If LPT1 does not appear, another printer or peripheral device is
using LPT1. In this case continue the installation, and after the
installation is finished, change the port setting so that the machine
can use LPT1.
•The Add Network port button is used when the machine is...

e-STUDIO162/162D/151/151D UNPACKING AND INSTALLATION  5 - 10 6) Select the network printer that is shared and click the OK button.
Ask your network administrator for the server name and printer
name of the machine on the network.
7) In the printer port selection window, verify the network printer that is
shared and whether the machine is to be used as the default
printer, make the selections and click the Next button.
8) When you are asked to select the model name, select the model
that you are using and...

e-STUDIO162/162D/151/151D UNPACKING AND INSTALLATION  5 - 11 5) Select SC1: from the Scanner events pull-down menu.
6) Select TOSHIBA Button Manager E in Send to this application.
Note: If other applications are shown, deselect the checkboxes for the
other applications and leave only the Button Manager checkbox
selected.
7) Click the Apply button.
8) Repeat Steps 5) through 7) to link Button Manager to SC2:
through SC6:.
Select SC2: from the Scanner events pull-down menu. Select
TOSHIBA Button Manager E...