Toshiba Estudio 162 Owners Manual

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 22 46 29 Image contrast adjustment 
(600dpi) (GAMMA 600)[Function]
Contrast is set for each mode.
When this test command is executed, the current se value is displayed in 2 digits (Default: 50).
Change the set value and press [START] key to make a copy under the set value.
When the set value is increased, the contrast becomes higher. When the set value is decreased, the
contrast becomes lower.
In this case, only Exp.3 copy is made. When,...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 23 46 32 Copier color reproduction 
setting (COLOR 
REAPPEAR)[Function]
Used to set color reproduction in each mode. Colors easy to be copied and colors difficult to be copied
can be switched.
∗This setting has virtually no effect on black-and-white documents.
When this test command is executed, warm-up and shading are performed and the current set value
is displayed. (Default: 0)
Press [START] key to make a copy under the set conditions . At...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 24 48 01 Main scan/sub scan 
direction magnification ratio 
(COPY MAG.)[Function]
Used to adjust the magnification ratio in the main scan (front/rear) direction and sub scan direction.
Enter the adjustment value with [10KEY]. Press [START] key to save the set value and make a copy.
(When the adjustment value is increased by 1, the magnification ratio is increased by 0.1%.)
The adjustment mode can be changed by pressing [
←/→] key. (Adjustment...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 25 49 01 Download mode 
(DOWNLOAD MODE)[Function]
When this test command is executed, DLOWNLOAD MODE is displayed on the LCD and the
machine goes into the program writing mode from PC to Flash ROM.
Use the writing tool on the PC and write the program. 
During writing, the display shows as follows:
After completion of download, turn OFF/ON the power to reset.
In case of an error in download, the following message is displayed on the LCD.
To...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 26 50 01 Lead edge image position 
(LEAD EDGE)[Function]
Used to adjust the copy image position and the lead edge void amount on copy paper. The adjust-
ment is made by adjusting the image scan start position at 100% and the print start position (resist
roller ON timing). When this test command is executed, the current set value is displayed in 2 digits.
(Center value: 50)
When [
←/→] key is pressed, the setting mode and the display are...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 27 50 06 Copy lead edge position 
adjustment (ADF/RADF) 
(ADF/RADF EDGE) 
(Disabled when set to OC) 
(Executable only when the 
ADF/RADF is installed.)[Function]
Used to adjust the ADF copy lead edge.
When the adjustment value of the document scan position adjustment is increased by 1, the scan
start timing is advanced by 0.1mm. 
The print result is shifted to the opposite direction of the scan start position.
The adjustment mode can be changed...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 28 50 18 Memory reverse position 
adjustment in duplex copy 
(DPLX REVERSE) (Enabled 
when Duplex setting is ON 
with OC or ADF set) 
(Executable only when the 
RADF is installed.)[Function]
When this test command is executed, the current set correction value is displayed.
Enter the correction value and press [START] key to save the entered correction value. (Correction
value range; 1 – 99, Default: 50)
For S-D mode front surface print and...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 29 51 02 Resist amount adjustment 
(RESIST ADJ.)[Function]
Used to adjust the contact pressure of the main unit resist roller and the RADF resist roller onto paper.
When this test command is executed, the current set value is displayed. 
The adjustment modes can be selected by pressing [
←/→] key.
Enter the adjustment value with [10KEY] and press [START] key to save the set value and make a
copy.
(*): Support for the installation models. For...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 30 63 01 Shading check (SHADING 
CHK)[Function]
Used to display the detection level of white plate for shading.
When [OK (ENTER)/START] key is pressed, the mirror base unit moves to the white plate for shading
and the copy lamp is lighted.
When the light quantity is stabilized, revision is made for every second, and the level of one pixel at
the center of CCD which is not corrected is detected and the value is displayed in decimal values on
the...

e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 31 64 01 Self print (1by2 mode) 
(SELF PRT.)[Function]
The status of the optical section is ignored and printing of one page is made. Also when the print com-
mand is received from the host, printing is made.
When this test command is executed, warm-up is performed and the ready lamp is lighted. (Since,
however, the scanner is disabled, initializing is not made.)
Enter the code number and press [OK (ENTER)/START] key to start paper feed from...