Toshiba Dp5018ds Instruction Manual

5Headset and Handset Operation
The DP5000-series telephone come standard with a built-in headset interface.
Recommended Headsets
For an extensive list of recommended and supported headsets please visit Toshiba\qs 
website at www.telecom.toshiba.com
Important! If you experience any electrical interference when using a wireless 
headset, please follow headset manufacturer\qs recommendations or 
ensure the headset base unit is at least six inches from your telephone.
Headset and Handset Interactions
When...

AUTO or CARBON Setting
There exist two types of headsets: ECM and Carbon. The default setting on the tele-
phones is AUTO. When the headset is connected to the Headset Modular Connector 
of the telephone, the AUTO setting enables the headset I/F current detector to deter-
mine which headset type is connected (EMC or Carbon). If the current is marginal 
using a carbon headset (only) and performance is not good, change the setting to 
CARBON.
‰  To change the setting from Auto to Carbon
Telephones:  All...

‰ To change the headset transmit level to Low or Normal
Telephones:  All except Single Line Telephone
1.  Press 
3+6+9+Hold (simultaneously).
2.  Press 
Spdial.
3.  Press 
FB2 to toggle On/Off.
FB2, LED On: Low
FB2, LED Off: Normal (default)
4.  Press 
Hold to set the option.
5.  Go off-hook, then on-hook to exit program mode.
Telephones:  Single Line Telephone
1.  Press 
3+6+9+Hold (simultaneously).
2.  Press 
Spdial and press 2.
3.  Press 
Msg to toggle On/Off.
Msg LED On: Low
Msg LED Off: Normal...

Headset Transmit Level Adjustments
‰	 To	set	the	 level	 of	the	 Headset	 Transmitter 	for 	DP5000-series	 telephones
1.  Press 
3+6+9+Hold (simultaneously).
2.  Press 
#.
3.  Set the headset transmit level using FB1, FB2 and FB3. For Single Line 
Telephone (SLT), use 1,2,3 and Msg. See table below.
4.  Press 
Hold. 
5.  Go Off-hook, then on-hook to exit the program mode.
Strata CIX DP5000-series Telephone UG     01/08 

Handset Level Adjustments
Change the Carbon setting if a Carbon type handset or headset is connected to the 
handset jack. This feature is not available on the Single Line Telephone (SLT).
‰  To change the Carbon Setting
1. Press 
3+6+9+Hold (simultaneously).
2.  Press 
Spdial.
3.  Press 
FB1 to toggle On/Off.
FB1, LED On: Carbon type handset
FB1, LED Off: DP5000 ECM handset (default)
4.  Press 
Hold to set the option.
5.  Go off-hook, then on-hook to exit the program mode.
‰  To adjust the Handset...

‰ To adjust the Handset or Headset Receiver Level for DP5000-series telephones
1. Press 
3+6+9+Hold (simultaneously).
2.  Press 
Redial.
3.  Set the level using the buttons shown in the table below.
4.  Press 
Hold to set the option. 
5.  Go Off-hook, then on-hook to exit the program mode.
‰  To adjust the Handset Side Tone Level for DP5000-series telephones
Note  This feature is not supported on the Single Line Telephone.
1.  Press 
3+6+9+Hold (simultaneously).
2.  Press 
Redial.
3.  Set the level using...

Strata CIX DP5000-series Telephone UG     01/08
1. Press 3+6+9+      (Hold) (simultaneously).
2.  Press 
0.
3.  Press Feature Button 4 (FB4) to toggle On/Off.
FB4, LED On: Call Waiting tone
FB4, LED Off: No Call Waiting tone
4.  Press      
(Hold) to set the option.
5.  Go off-hook, then on-hook to exit the program mode.
1. Press 3+6+9+      (Hold) (simultaneously).
2.  Press 
Mode soft key.
3.  Press     
(Msg) button so that the     (Msg) LED is On. 
4.  Press      
(Hold). This sets the LCD...

Strata CIX DP5000-series Telephone UG     01/08
1. On the DKT3x00 telephone, press 3+6+9+      (Hold) (simultaneously).
2.  Press 
#.
3.  Press 
FB7. LED On = 2000 telephone. LED Off = 5000-series telephone.
4.  Press      
(Hold). 
5.  Lift the handset to exit programming mode. Wait a few seconds for the telephone 
to reset itself. 

Date and Time Setting
This operation is possible from the Administrator station or attendant consoles and 
enables you to set the date, time, and day.
‰  To set the date
1. With the handset on-hook, press a DN + the access code assigned in eManager.
A confirmation tone is heard.
2.  Enter the date (YYMMDD).
3.  Press 
Redial.
A confirmation tone is heard.
4.  Press 
Spkr.
The telephone returns to the idle mode.
‰  To set the time
1. Press DN + the access code assigned in eManager,
 with the handset...

Telephone Programming Mode
‰	 To	place	your	telephone	 in	Programming	 Mode	A
‰  Press 
3+6+9+Hold simultaneously. The LCD displays “DP PROGRAM 
MODE” and “SELECT=”. Your phone will not ring if it receives a call while in 
Programming Mode. 
‰  To exit from Programming Mode A
‰ Go Off-hook and On-hook or wait for 30 seconds for Programming Mode to 
automatically time out.
Initialize Telephone Settings
This function resets all Programming Mode option settings to their default setting.
1. Press 
3+6+9+Hold...