Toshiba Bex4t2g Manual

3. ONLINE MODE ENGLISH VERSION EO1-33094 
3.3 Operation Example 
E3- 5 
3.3  Operation Example (Cont.) 
„ Cancellation of Print Job 
 
  
Idling or normal issuing 
  
 
  
 
   
 
 
 
  
If an error occurs while 
printing: When [PAUSE] key is 
pressed while printing: 
Hold down [CANCEL] for 3 sec. or more. 
Hold down [CANCEL] for 3 sec. or more.
While [CANCEL] is held down, the received data is discarded. 
(Quick reset) 

3. ONLINE MODE ENGLISH VERSION EO1-33094 
3.4 Power Save Function 
E3- 6 
3.4  Power Save Function 
 
3.4.1  Entering the Power 
Saving Mode 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
3.4.2  Exiting the Power 
Saving Mode 
 
When the printer stays in any of the following statuses for the 
specified length of time, it enters the power saving mode.  
•  Online (Idle, communicating) 
• Pause 
• Error 
•  Waiting for label to be removed 
•  System mode (except for self-diagnosis, test print,...

4. MAINTENANCE ENGLISH VERSION EO1-33094  4.1 Cleaning
 
E4- 1 
4.  MAINTENANCE 
               
4.1  Cleaning      
4.1.1  Print Head/Platen/ 
  Sensors 
             
   
This chapter describes how to perform routine maint enance.  
To  ensure  the  continuous  high quality  operation of  the  printer,  you 
should  perform  a  regular  maintenance  routine.    For  high  usage  it 
should be done on a daily basis.  For low usage it  should be done 
on a weekly basis.                   
To maintain the...

4. MAINTENANCE ENGLISH VERSION EO1-33094  4.1 Cleaning
 
E4- 2 
   
  
4.1.1  Print Head/Platen/
  Sensors (Cont.)                   
4.1.2  Covers and Panels      
           
6.   Clean  the  Print  Head  Element  with  a  Print  Head  Cle aner  or  a 
cotton swab or soft cloth slightly moistened with a lcohol. 
                 
7.   Wipe the Platen, Feed Roller, and Pinch Roller wit h a soft cloth 
slightly  moistened  with  alcohol.    Remove  dust  or  fo reign 
substances from the internal parts...

4. MAINTENANCE ENGLISH VERSION EO1-33094  4.1 Cleaning
 
E4- 3 
 
4.1.3  Optional Cutter Module 
                                           
    The  disc  cutter  and  rotary  cutter  are  available  as 
an  option.    They 
are  both  cleaned  in  the  same  way.    When  removing  th e  Cutter 
Cover  of the  rotary  cutter  unit,  remove  the  screws  from the  bottom 
of the cover.   
1.   Loosen  the  two  Plastic  Head  Screws  to  remove  the  C utter 
Cover.  
2.   Remove the jammed paper. 
3....

5. TROUBLESHOOTING ENGLISH VERSION EO1-33094  5.1 Error Messages
 
E5- 1 
5.  TROUBLESHOOTING 
This chapter lists the error messages, possible pro blems, and their solutions. 
           
  
5.1  Error Messages       
  
  
Error Messages  Problems/Causes  Solutions 
The Print Head Block is opened in  
Online mode.  Close the Print Head Block.   HEAD OPEN 
Feeding or printing has been  
attempted with the Print Head Block 
open.  Close the Print Head Block.  Then 
press the 
[RESTART]  key. 
COMMS ERROR...

5. TROUBLESHOOTING ENGLISH VERSION EO1-33094  5.1 Error Messages
 
E5- 2 
5.1  Error Messages (Cont.) 
Error Messages  Problems/Cause  Solutions 
1.  The media is jammed in the  
cutter.  1.  Remove the jammed media.  Press 
the  [RESTART]  key.  If this does 
not solve the problem, turn off the  
printer, and call a TOSHIBA TEC  
authorised service representative. 
  Section 4.1.3 . CUTTER ERROR   
(Only when the cutter  
module is installed on  
the printer.) 
2.  The Cutter Cover is not attached...

5. TROUBLESHOOTING ENGLISH VERSION EO1-33094  5.1 Error Messages
 
E5- 3 
5.1  Error Messages (Cont.) 
Error Messages  Problems/Cause  Solutions 
1.  The printer is used in a location  where it is subject to noise or  
there are power cords from other  
electrical appliances near the  
printer or interface cables.  1.  Keep the printer and the interface 
cables away from the source of 
noise 
2.  The Power Cord of the printer is not grounded.   2.  Ground the Power Cord. 
3.  The printer shares the same...

5. TROUBLESHOOTING ENGLISH VERSION EO1-33094 5.2 Possible Problems
 
E5- 4 
5.2  Possible Problems  
This section describes problems that may occur when  using the printer, and their causes and solutions.  
 
Possible Problems  Causes  Solutions 
1.  The Power Cord is disconnected.  1.  Plug in the P ower Cord. 
2.  The AC outlet is not functioning 
correctly.  2.  Test with a power cord from 
another electrical appliance.  
The printer will not  
turn on. 
3.  The fuse has blown, or the circuit breaker...

5. TROUBLESHOOTING ENGLISH VERSION EO1-33094 5.3 Removing Jammed Media 
E5- 5 
5.3  Removing Jammed  Media  
                            This section describes, in detail, how to remove ja mmed media 
from the printer.       
1.   Turn off and unplug the printer. 
2.   Open the Top Cover. 
3.   Turn the Head Lever to  FREE position, then open the Ribbon 
Shaft Holder Plate. 
4.   Open the Print Head Block.  
5.   Remove the ribbon and media. 
              
6.   Remove the jammed media from the printer....