Tone Commander 7210, 7220 Ip Centrex Telephone User Manual

26Tone Commander 7210/7220 User Manual
If DHCP is currently enabled, select DISABLE.
Press the Done key to return to the IP Configuration Update
menu or the Setup key to exit Setup Mode.
Manual IP Configuration
DHCP should be disabled if manual IP configuration is used; IP
addresses configured via DHCP will overwrite manually entered values.
From the Installation Options menu, select IP.
(Setup → INSTL → IP)
Select PHONE, TFTP, GATEWY, iMERGE, SNTP, or
SUBNET.
Using the dial pad, enter the IP addresses....

Tone Commander 7210/7220 User Manual27
To test the phone, gateway/router, TFTP server, SNTP server,
or iMERGE address, select PING. If you have entered a new
phone IP address, the phone must be restarted before ping
will work properly.
If a response is received, indicating a valid address, PING
SUCCESSFUL will be displayed.
If no response is received, the entered address is invalid.
PING FAILED will be displayed.
Press any key to return to the previous menu.
Alias Entry   _____________________________
A...

28Tone Commander 7210/7220 User Manual
Using the dial pad, enter the alias supplied by your network
service provider.
If you need to make corrections, select 
ÅBKSP (backspace)
to delete the previous digit.
CLEAR removes all digits, allowing you to start over.
When all digits have been entered, press the Done key to
return to the Change Password menu or the Setup key to exit
Setup Mode.
SPID Entry   _____________________________
A unique SPID (Service Profile IDentifier) is required for operation of
the...

Tone Commander 7210/7220 User Manual29
IP Configuration and Software Updates   _____
Telephone operating software and configuration parameters can be
automatically updated daily from the TFTP server at a preset time,
manually updated from the phone using files on the TFTP server, or
updated from a client PC.
Automatic Update
A properly configured network TFTP server is required for automatic
updates. Please refer to the 7210/7220 Network Administration Guide.
From the Installation Options menu, select...

30Tone Commander 7210/7220 User Manual
simultaneously requesting updates. You may manually enter
the minutes digits, but it is recommended that you use the
default calculated value.
If you need to make corrections, select 
ÅBKSP (backspace)
to delete the previous character.
When all changes have been made, press the Done key to
return to the IP Configuration Update menu or the Setup key
to exit Setup Mode.
Manual Update
To perform a manual update, the phone must have the TFTP server’s
IP address entered...

Tone Commander 7210/7220 User Manual31
If a new version program is not found, the following screen will
be shown. Press any key to return to the previous menu.
If phone configuration files are missing from the TFTP server,
or the correct TFTP server address has not been entered or
set via DHCP, the following screen will be shown.
Select EDIT.
Enter the correct TFTP server address. You can verify the
address by selecting PING. When finished, press the Done
key.
If you need to make corrections, select...

32Tone Commander 7210/7220 User Manual
Select FLASH.
Select ENABLE.
After updating, you can disable flash updates to prevent inadvertent
changes to the phone configuration.
Telnet
This option allows a telnet client to connect to the phone for
troubleshooting purposes.
From the Installation Options menu, select UPDATE.
(Setup → INSTL → UPDATE)
Select TELNET.
Select ENABLE.
When telnet capability is no longer needed, disable it to prevent
inadvertent changes to the phone configuration.
FLASH...

Tone Commander 7210/7220 User Manual33
Configuring Keys   _______________________
If the network does not support ISDN Parameter Download, you must
assign call appearances, directory numbers and feature activators
using this option.
From the Installation Options menu, select KEYS.
(Setup → INSTL → KEYS)
The status indicator for each key will indicate the current
setting.
Green– Call Appearance or DSS.
Red– Feature Activator.
Off– Unused or Speed Dial.
On the phone or expansion module, press the...

34Tone Commander 7210/7220 User Manual
Call Appearance / Directory Number Keys
These “line” keys are used to place and answer calls. If you have
BASIC service, each directory number key is assigned a unique
directory number. If you have CACH EKTS service, one directory
number may be assigned to multiple Call Appearance keys; multiple
calls can be handled on one directory number.
Enter the assigned directory number with the dial pad.
If you need to make corrections while entering numbers,
select 
ÅBKSP...

Tone Commander 7210/7220 User Manual35
To change the Originating DN assignment:
Select ORIG.
Select YES or NO from the Originating DN menu.
Press the Done key to return to the CA/DN menu.
To change call appearance reservation:
Select RESERV.
Select the call appearance reservation for this CA/DN.
OUT– Originate (outgoing calls) only.
IN– Terminate (incoming calls) only.
PRI– Outgoing or priority incoming or calls only.
NOT– Not Reserved – default value for all keys.
Press the Done key to return to the...